Ya but who’s really gonna take that Lexus 550 off road that’s gonna be a pavement princess ….they’ll just get 4 runners and the gx470 Toyota FJ , or some off road midsize pick ups … only people who will try it is people who have money to Just blow cause they bored
As someone who works in the off road industry and on behalf of everyone I work with. Thank you for helping all of the forum geeks and RU-vid mechanics understand why they have no idea what they are talking about when it comes to suspension
The 3rd gen 4runner I bought had the worst set up. -Maxed out suspension lift -no rear sway bar -front sway bar Drove like dogshit. After watching Tinkerers swaybar videos I made the corrections and it made the BIGGEST difference. This is the best channel for this kind of stuff. Amazing, thank you
@@ananamusly removed strut spacers from front coilovers, put in a rear sway bar and removed the front sway bar. I also found out the front lift coils didn’t have the proper weight rating to handle arb bumper+winch so will be ordering proper coils eventually
@@kevinVersus adding back in the rear sway bar on my Xterra for some measurements has been on my list since he released that video. Awesome, technical content.
@@thomascarpenter5536 do it up. I have a 1st gen pathfinder and I run no sway bars. It’s lifted on 33’s but I have the clearance for full flex (required cutting)
@@thomascarpenter5536 Definitely worth trying. My stock 2nd gen Frontier seems to get all of it's articulation from the rear end currently. Removing the front swaybar and leaving the rear would probably perform very similarly to how the same setup performs on Toyotas, and a few anecdotes I've heard from other Frontier owners confirms that.
I've noticed this trend for a little while now. Rigs with 1.5" lift or less, only 32-33" tires, and lower total vehicle weight seem to walk over obstacles more easily than the incredibly overbuilt vehicles. Just my anecdotal observation.
Yep, I did 1.5” lift on my sequoia and have run 32” and 33” tires. Been a great setup for me for the last 5 years. That combined with a skinner tire and as minimal offset as needed to keep it from rubbing the frame.
I’m only going to go as big as I can fit in the spare tire area. Makes no sense to have to get a hitch carrier to hassle with every time I open the rear lift gate
Couldn't agree more. I originally had the front end of my 2nd gen set at 3" lift w/ 33s, but had maybe 20% down travel and poor handling, always topping down when articulating. I lowered it down over an inch and it is far more capable on high/low speeds, but still has plenty of clearance for most trails I hit.
@TobyCostaRica I had a dirtcom carrier on my GX460 for a minute and i sold it within 3 months. It sucked on a daily driver. I’m just glad my LX570 will fit a 315/70 underneath.
@@brianpeck697 not just numbers but the entire scientific method, he has theory, hypothesis, experimentation, analysis, conclusion and iterations, the videos are about as complete as they can be.
Getting a GX engineer on your channel is the ultimate flex! You know he is proud of his product and stands behind it. Toyota is lucky to have this man. Can’t say I’ll buy a GX. But your videos have me sold on Toyota as my next vehicle.
*"Not lifted" since day 1 in our Lexus GX460. Explaining the reasoning to the masses has been an exercise in futility. The low COG combined with articulation simply keeps things planted. The lifted counterpart already thinks it's in a ditch and starts to get tippy rather than conforming and building confidence. Lastly, all Toyota engineers know what a "lift kit" is and how the ultimate goal of a balanced suspension geometry is the actual aim. Sadly stock suspension geometry is never really put to the test by many buyers because "lift kit" has been pre-programmed in their mind as some sort of offroading prerequisite... or more accurately: they do it for looks*
I'm all for not running lifts, especially huge ones. I ran my GX460 for 3 years with the stock suspension, skids and 285/70's and it was fine. But usually lifts consist of better shocks and springs than stock and improve many aspects of the vehicle besides just lifting it. Obviously, Lexus didn't tune the GX460 suspension tuning with pure offroad performance in mind. At the end of the day its used as a grocery getter by 99.9% of first owners and its a compromise of on road comfort and handling with a little offroad sprinkled in. Additionally, most aftermarket shocks for a GX460 are extended travel, meaning you can gain about 1" of additional droop travel. As long as you do not go for a huge amount of lift while doing this, the truck will be improved in most respects. I went to Bilstein 6112's with the heavy rate springs and kept it as low as possible. Eibach medium rate load leveling springs in the rear with Bilstein 5160's. The truck rode better in all conditions than the factory setup. Since I used the GX to tow, the heavier rate springs were a big improvement there, but still very compliant offroad.
Sadly you are restricting yourself to trails that only requires about 10 inch of ground clearance, which is common in CA where desert trails are usually not that demanding. There are tons of places in other states where stock height GX will immediately get destroyed.
After taking my LC250 out on the trail, it got me thinking that I may not need a lift. It handled everything with ease and comfort. Made it out unscathed. FYI: I did gain 1" of ground clearance running "33s"(32.8in).
This is by far the most informative channel on 4wd suspension. You're making me want to flex test my Pajero Evolution as I have 40mm lift and fixed swaybars... interesting to see how much flex I've lost!
I wanna see that. New Pajero SWB owner. My target is for corrugated roads, sand, and minor travels. All with easy maintenance and low price. Not interested in spending heaps for rock-crawling or river crossing, that is more a job for modified Nissan Patrol, Toyota Prado, and Lexus LX models.
Suspension droop is the un-sexy unsung hero in the offroad world. Jack the thing up, so you can put bigger tires on so it looks cool is unfortunately what way to many people are after vs actually performing well off road. Thanks for helping all of us data geeks get our numbers fix tinker!
I am on my fifth IFS ute (truck) now and this one I've left bog stock in the suspension both ends. Although it helps being a Ranger Raptor, I had a previous gen RR prior to this one with a 2" lift both ends and cannot believe how much better the new standard one performs over the "improved" one (and the other three lifted vehicles I had prior)... I agree with your point about the specific type of offroading you do being important to understand before modifying, or leaving standard, your 4x4. In my case, standard height causes no problems as never work it on rocky trails where clearance is critical. This is one of the best produced videos I have seen on this topic!!!! Well done to you and the crew that helped put it together
Just tried this with some wood blocks and Rhino ramps on my stock '21 Chevy Colorado ZR2 (sway bar connected). I still was making good contact with the ground (front and rear) so I did not get full flex but I measured 4.5 in the front and 14.75 in the rear. This channel certainly has done a good job of showing some very valuable 4x4 suspension information. Keep them coming.
Update: I built some taller ramps and disconnected the sway bar. Front Flex: 6.5 in. Rear Flex: 15.25 in. Total: 21.75 in. I was at the end of my ramps still so there might even be a little more flex yet.
This is why I would love to see you review the Bronco and similar mods. The stock Bronco flexes very well (with disconnect of course) because of the decent wheel travel and specifically the down travel. Ability to fully stuff the jounce tire is also pretty good. So many common mods really kill the flex and give IFS a bad reputation.
Agree! I haven't seen it in person, but I watched a lot of Bronco videos and they do seem to be quite impressive for IFS. I'd also be curious to see an LE3 or LR4 Land Rover with air suspension, the way they work is as one wheel goes up, the air forces the opposite wheel down, so it functions almost like a solid axle.
My friend took me on some mountain trails in Ouray, Colorado in a stock late 70's Jeep. There were lifted jeeps and fjs everywhere. I was completely blown away by what we could go up and down. I haven't modified my truck, and probably will only replace the shocks. I don't want to lift it and see no advantage to it. 4wd and a locker will get you very far. My gf test drive a bronco, with a factory lift kit and 35" tires. An extra $13k in value. It was stupid and didn't look good. A level bronco on 31-32" tires looks so much better and I'm sure performs at 95% of what a lifted one can, without the crappy on road experience.
@@Alan-bm3ni Old jeeps are a lot different than modern Toyota's though. The GX460 in this video comes with pretty atrocious clearance stock. Mine was stock with 33's on it and still was smacking running boards and bumpers and the trailer hitch on mild forest service roads. A Bronco has much better approach and departure angles but the 4 door version has a pretty long wheelbase so breakover could be a concern.
Well done, as usual. When people can't understand why my raptor can often go where lifted vehicles can't, it's often the droop. I try explaining this and a large proportion of people simply look confused. Some totally get it. Lifts, body lifts... all have their place depending on people's budgets, needs (and wants). All good. Info like this video help people prioritize or plan their upgrades.
It depends on what kind of off-road driving you’re doing. For rock crawling down travel, but for fast dirt road or Baja style desert up travel is more important.
I simply removed my front sway bar from my 1st gen Sequoia, and when combined with the basic 2 inch lift the front articulation is pretty impressive for what it is. Plenty of droop, but also stuffs the front 33s into the fender. I personally think the fat tire and low offset craze is kind of ridiculous. Your videos have helped me get my Sequoia performing pretty well.
The smart people with GX's run 4Runner TRD Offroad wheels with +15mm offset that the 4Runner bro's sell to replace with Methods or SCS wheels. 🤣 We don't look that cool, but its cheap and functional and was able to fit 285/70's with minimal effort.
What an eye opener! I have a Westcott Designs Lexus GX 550 Preload Collar Lift Kit. I gained 2 1/2" of lift in the front and 3/4" in the back. It allows me to run Toyo Open Country AT III 35x12.5x17 tires on Method MR703 BeadGrip 17x8.5 wheels with a +35 offset. I was focused on improving the Approach & Departure angles and hadn't considered the flex ramifications. But it sure gives the 550 a great look!
Frank, please get rid of the spacer lift. Those things are garbage and don't listen to what Westcott says about it not affecting performance. With any type of spacer lift, performance will be worse in all aspects and they will ride like donkey shit. Just the facts.
@@Gazziza29 You do know that the factory Land Cruiser 200 series had the option of a 10mm spacer lift? The factory shocks still have plenty of uptravel available after the bump stops engage, so a small spacer only moves the shock down slightly but improves down travel and retains up travel without damage to shocks. Spacer lifts are not bad if you do it right and keep the shock protected by bump stops.
@@Jay-me7gw BIG difference between a 10mm spacer vs 60+mm. Pre-load spacers are the least desirable type, you're trading every mm of downtravel for every mm of lift. With strut spacers, at least some downtravel is retained, limited only by CV angle and upper control arm spring contact.
@@royj8549 the Westcott design spacer is not 60mm. They are like 10mm. I doubt anyone makes a 60mm spacer, that would lift the front like 5". Also, why would a pre-load spacer trade any travel. All its doing is compressing the spring a little more. The shock still has the same travel range. Yes it will be harder to fully compress, but thats how any lift works. And a preload spacer is the only way to help the suspension cope with heavier weight from winches, bumpers, skids, etc besides going to stiffer springs.
@@Jay-me7gw Usually, spacer height refers to effective height. Just like when we talk travel on a GX, we're not talking strut shaft travel, but effective wheel travel factoring in motion ratio. As shown by the GX460 in the video, factory spring rates are chosen so you're at bump stops under corner loading / articulation. You raise it 60mm (2.5"), and you won't use that extra bump travel, but you lose that in droop. A strut spacer maintains the bump / droop ratio within a couple % For weight compensation, sure. But not a 2.5" spacer. For GX460: 730 lb-in x 2 x .53 motion ratio = 774 lbs per inch of sag. How much weight you adding to the front end?
The principle is what I learned about 15 years ago called a “low center of gravity” lift, or “LCG” Suspensions built for prerunners also use this principle in their builds. Huge 35 BFG Baja TA with plenty of limitation of uptravel, but huge amounts of downtravel at each wheel.
NB: This applies only to IFS, not a solid axle. My XJ has 33" tires on a 4" lift and I cut back the wheel wells to make more room. Now I have lots of extra travel, up and down, both front and rear. IFS is great on road but I'll stick to solids off road for both travel and strength.
This is incredible. I’ve thought of lifts just moving the truck up the useable travel without actually adding more flex but never known of the science behind it. Great job explaining this, testing it, and visualizing this.
Very in-depth super-informative video bro! I'll stick with my stock GX460 for it's plush ride and the fact that it takes me anywhere I want to go in style.
This also reminds me of the Nissan world, Especially for F-alpha platform. We do "Titan swap" on front suspension for wider track width (3in wider on each side) This helps with better total travel distance both up and down. And with longer CV axles, it helps to eliminate binding when reach to full droop.
When I was planning my lift on my '18 GX, I probably watched your IFS videos about this 20 times or so. I went with the same extended travel coilovers, and achieved a tiny bit more articulation over stock while gaining a few inches from the suspension/fitting 33's. It's been nothing short of amazing out on the trails I like to go on. Thanks for sharing the testing and research!
@@AlexM-np1cx yeah, for sure. Ironman stage 2 foam cell pro kit (2.5” front which I backed off a tiny bit, and 2” rear which I also backed off a tiny bit, as the air bag delete kit I also got from them adds 1/2”), I’mprobably sitting at around 2.15” of suspension lift after settling. DrKDSS botck, KDSS spacers, kdss switch, SCS -10mm Ray10 17” wheels, 285/70R17 Load C Toyo RT Trails, body mount chop, lots of fender liner heating and reforming. JWOffroad single tire carrier to handle the oversized spare. OEM trans cooler, Redarc trailer brake controller.
It’s been a wonderful rig to get out on pretty gnarly trails, yet still drives nicely on-road. The setup really helped with approach and departure angles, which from time to time it still struggles with.
The one thing you miss by not lifting is extended travel shocks. Running extended travel shocks with minimal lift will be an improvement in terms of total articulation and still allow the truck to flex. Its when you start going 2.5, 3, or 3.5" of lift that things start to go sideways, but with the right shock and spring selection you could easily keep it to 1" lift.
@@toddmanning7844 Most any lift shock should be extended travel. Eibach, Bilstein, OME, Dobinsons, Ironman, Fox, Icon, King. Which ones just depend on your budget.
You could also put 1/2” spacers up front and 1” spacers in the rear for very little money and have the same effect. Check out some of the earlier Toyota suspension videos on this channel.
Everything in this video is why I support the use of bracket lifts on properly built rigs. Everyone out there is chasing bigger tires, so they crank their pre-load and lose down-travel. All that pre-load requires more weight to overcome it and compress that spring, so they lose up-travel as well. All that and they have a set-up that looks cool, but has 5" of total travel and 35" tires. Since a bracket lift moves the wheel travel range downwards relative to the frame and body, it increases the room for bigger tires without sacrificing up-travel or down-travel. For example, my truck has a 7" BDS bracket lift, and I reduced the pre-load on the coils to achieve 5.5" of total suspension lift over factory. I have ~12" of total wheel travel on my IFS, with half of that being down-travel. And I run 40" tires without rubbing at full compression. I use the bigger tires for increased ground clearance, which helps especially on the rear solid axle. I hope that Kai can one day make a video detailing the pros and cons of a bracket lift on IFS trucks. I feel like it's information that everyone should know even if they're not in the market for a bracket lift.
Congrats on the ONX sponsor! I've torn my Chevy suspesnion apart so many times to understand how suspension actually works. I have twice the suspension travel on my truck thats raised 2.5 inches than my buddies 6 inch lifted truck does. Its quite interesting how it works.
My tahoe has 5.5 inches of total front end travel, which isnt much. Its less than stock. But, most torsion bar chevys only travel 3 inches up front once theyre lifted... my rear axle uses GM stuff with a custom trackbar and longer shocks, and has 16 inches of travel in the back
People are eager to sacrfice down travel to gain clearance for larger tires. I am going to stick to lower lifts and properly clearancing for larger tires.
This. And not run 12.5" wide tires with -38mm offset SCS wheels because they look dope. Get some skinnier tires with appropriate offset so you can continue to stuff them.
@@Jay-me7gwon the gx with a simple preload you can very easily run a 35x12.5 on a 17x8.5 but that is a massive off set. IDE recommend a+35 and you still are able to get full articulation on the gx550.
Hey, great video. Love how technical you are. I would love to see an analysis like that for a Rivian R1S to understand better how it perform/work. I own one, but we are probably too far for a quick test.
Great video, as someone that has always had solid axle off-road rigs I would have never thought of how the IFS rigs geometry would end up functioning like this.
Exactly, Kai!!! As always!!! The question for IFS lifters should always be, “do you even downtravel, bro?” Downtravel is 60% of off-road suspension capability … when you lose down travel, you lose vehicle capability. 👍👍
As a smug stock 3rd gen Tacoma owner, I did a bunch of research and came to the same conclusions. This is the first vehicle, after many modified ones, that I’ve decided to leave completely stock and I am loving it.
My stock 200 Series has always done just fine off road. Tin Cup, Engineer Pass ect. The only thing I have added are K2’s over the OEM tires, and Bud Built Rock Sliders and Skid Plates. Granted I’m not hitting crazy truck breaking trails, but most people aren’t. You need to upgrade to meet your needs and remember that every pound you add to the rig should be well thought out.
Basically if it has KDSS leave it alone. Get some shocks for ride quality and get a portal axle lift. Leaves all the factory specs in place and will help with clearance.
After watching the previous sway bar video, on my 3rd gen 4Runner, i: - took off the front sway bar, left rear in place - went from 700 lb front springs to 600 So far? Well, with no front sway, it's more ponderous on pavement, amplified by a switch to 'pizza cutter' sized KM3 tires. But off road? Way more balanced articulation. Previously I'd say that the body did about 90% of what the front wheels were doing, which isn't always a good thing. After? It's still somewhat front biased, but as a totally subjective guess, I'd call it 60/40. But I can really feel how the car is splitting the difference now, instead of making the rear axle do all the work. (1" body lift, 33" tires, 3" suspension lift, double locked, crawl box, manual trans '99) Love it, and it's not the sort of thing I would ever have thought up to try on my own. PS: I'm keeping the lift, I use the skid plates enough as is!
It really depends entirely on the environment in which you are wheeling in. In rocks, you will need clearance. In mud and water as well. Some times you want wide tires, in others, narrow. Various setups accel in different conditions.
This is a great video. Most people don't understand the physics, engineering and mechanics of this. I've never been a fan of lifts, especially really big and expensive ones. They usually cause more problems than they solve.
Thank you for making this video follow up to your original Toyota suspension series. I had lowered my 4Runner from a 3” to a 1” lift but my ego was starting to crave a higher lift again… putting those skid plates to work!
Ideally a 1" lift with 1" longer shocks/coilovers and a proper bracket diff drop kit is ideal setup. Then fit as big a tyre as can fit, regear and lockers, underbody protection and youll go almost anywhere. Here in Oz, the smart offroaders keep em as low as possible.
I don't "wheel" per se but do take a '16 F150 out into the Mojave to a couple of my favorite "fishin' holes". We fish for tin cans, paper, AR500 alloy, that kind of thing. Meanwhile, I wanted a little more ground clearance for my rig. 2" is the generally accepted limit to "level" a stock truck; after that you can get into the problems Tinkerer's Adventure describes here, and from lack of "droop", or, suspension downtravel. And since I carry gear in the bed of the truck and sometimes hang a small trailer's tongue weight on the hitch receiver, I did not level the front of my truck to 2" but instead opted for 1.5" front lift via the Bilstein 6112 (also, Bilstein 5100s offer a similar, 5-postition spring saddle placement before assembly), knowing that I was preserving some downtravel by not topping out my lift height. The compromise, there, payed dividends, as Tinkerer's Adventure illustrates so well in this video. I recently ditched the zero-offset 17 X 8.5 wheels I was running in favor of a +25 Method 705, which when wearing a new, NARROWER tire (Toyo's ATIII 34 X 10.50 X R17LT D Load Range), has eliminated the rubbing issues at full steering lock that I was having when using the zero offset. And the new tire is also TALLER. Win/win. Great vid, as always.
Experimenting on the lowly Jimny, day and night and then day again, this is what we got: 1. On solid axles the flex is fixed. Meaning you can cross flex it all you want, you can go all the way up the ramp with lockers and lift 2 wheels, you will still get the same amount of flex as stock. Whether you are lifted or not. It is restricted by the flex of the stock bushings, and if you upgrade to solid ones, you get even less. 2. Wheel - axle travel does not translate in flex. your whole axle might have 12" of travel (on the lift), if your flex is 9", you are not getting over a 9" obstacle (ramp) without a locker. So compressing the suspension, you will first get the 9" of flex, then the whole axle (both sides) will move upwards 3 more inches. 3. Sway bar is a killer of flex. Just completely unhook it for off roading. 4. Looser bushings, work better. More than that some people go as far as to unbolt one of the two bushings on one side of the axle (usually the outer most ones). This does result in more flex and better overall ride quality off road. 5. On the road - tarmac, ALWAYS have a connected sway and properly bolted and torqued bushings. Front end on 3rd and 4th gen Tritons, independent suspension, every thing is pretty much the same but one thing. You do get the whole wheel travel as flex, and that is pretty much it. So adding a long travel kit at the front while having a restrained back end will not help that much, given the fact that the rear is what pushes the car uphill, and this is where you need most of your traction. At that point, you 'd be better off with a 4 link setup on the back (where the pivot point is the center of the axle) and stock front. I will say I again and end my sheet, on public roads NEVER run your car on any setup that is NOT STOCK or state - country APPROVED.
Been off roading my entire life from atvs jeeps trucks sxs heavy machinery at work. In my experience ground clearance is king flex is important obviously but can be overcome to an extent with front and rear lockers. Most times I've been stuck I've been hung up on something either rocks deep ruts high centered. Also high clearance vehicles are better at river crossings especially swift water in Rockies like snow melt combined with storms flooding can happen quick. Snorkel doesn't help much if your washed down the river. When done right in most circumstances the higher vehicle will do better.
As a wheeler of full independent suspension vehicles, yes you are correct, and for most 'overlanders' and softroaders flex is more helpful than clearance. But for me and most people/places i wheel, clearance is more important as flex doesn't help you get un-turtled from large rocks. But you don't see many people talking about this though it seems common sense...stiffer suspension means less flex.
I have a 200 with long travel arms. I'm getting 13in of travel with stock AHC shocks. I added 1.25" strut spacers to change the range of motion (sacrificing compression for droop) making my wheel travel more usable. I did have to cut 2 in out the fender. It is a happy compromise to run 35s and not have to limit travel. Great videos keep it up
In the end of the day it depends on the case. Different off-roading requires or at least favours different suspension (and not only) setups. Furthermore, a thing you said yourself, it matters how you lift the vehicle. A proper lift means all the parts can work with each other - longer shocks, longer control arms, adjusted bump stops, maybe limit straps, removing the anti roll bar altogether, a lot of factors depending on your particular setup and needs. There's a difference between changing the ride height and putting a lift kit.
In Thailand, since factory rear locker come as standard in 4x4, we don't lift that high like in rigid axel era. Stock IFS with few lifted saves $$$ and capable enough on most terrain except rock climbing & water crossing. My 4x4 is 1.5" lifted on stock IFS and trim the fender to put 35" tire. Easy to drive and not easy to rollover. And on extreme 4x4 trip, I just left my sway bar at home.
You should do a special video on Ford Bronco, Explorers, Rangers, and F150s of the 1990s with TTB Front Suspension. That's an eye opening option that people haven't heard about much in the past 2 decades.
Thanks Kai. Super informative. I'd always go back to watching your videos for reference whenever I'm unsure about lifting my '10 Hilux. Keep 'em videos coming!!!!
I wish I new more, I got my first truck - fj-80 95 and it came with some lift, think it's 3" not sure, but I have to work on it and give it basic care before I can really take it off-road. Definitely a fun world to explore
Looking forward to the gx550 full review. Im hoping you will cover things like axle and differential size and strength, etc! Also curious what a rear seat delete would ultimately look like!
this is a super cool video! so many people throw parts and upgrades at a truck and don't think of what the big picture will be or have any real goals for the vehicle's capabilities. It's just "upgrade this" "upgrade that". some parts you "upgrade" make the vehicle worse in some other way and it all adds up! The real question is "how much ground clearance is enough" how much ground clearence makes you feel comfortable to take on any / most trails?
Not all lifts are dond at tgd expense of teavel. On my lift (not a toyota) the lower control arm is repositioned with add on crosmembers and a longer knuckle and modified upper A arm move compensate for the larger distance between upper and lower A arms.
Your channel is excellent. It has changed how I look at suspension setup. I am interested in RC crawlers as well. My most recent RC build was definitely inspired by your "lessons" about balance and making all four corners working more harmoniously. Without going into detail on the setup, the end result is a chassis that stays very level while going through it's articulation cycle It has the ability to "float" a tire across a gap without dropping the tire too fast, which keeps the chassis much more planted and less prone to rocking. I always look forward to your videos, as they are of the highest quality and are very intelligent. Keep up the good work.
Droop travel setups has been popular in the RC crawler world for a while. Some guys will run their RC's with the shocks basically bottomed out at normal ride height so the tires can only drop down. It lowers the center of gravity and also makes it so that, when the truck is on a side hill or climbing, the downhill shocks are already bottomed out and wont cause the truck to lean and roll. I had a TRX4 that I put extended shock towers on, and ran 120mm shocks at stock ride height. All the added shock length was in droop only and the thing was like a damn spider. The tires almost never left the ground ever.
Rollover!! I owned "Opel Frontera Sport B" (Isuzu Amigo based Vauxhall). It was considered crappy due to low lift and "only" LSD in rear differential. However it was a blast in mountains!!! 20° traverse was like nothing for that car! (Manufacturer claimed 40° but I didn't have the guts). Meanwhile my friend totaled "superior" Land Cruiser due to roll over 🤷
It's all about balancing the trade-off. That's the big takeaway. Lots of wheelers are forced into trading IFS articulation for approach/departure, breakover, and center-line clearance because of longer wheelbase. I run 31s and no lift on a Gen1 SWB Montero which is the max I'll ever go. The short wheelbase guys have it a lot easier but, in scenario's like your ramp test they get very tippy really quickly. And that's the trade-off I've made.
I just bought ( my bank did) a 214 Runner TRD offroad. and I happen to think its the perfect height. All I want to change up is the wheels/tires. And maybe a few LED mods. other than that, It's perfect.
Seriously excellent video and analysis, man. Keep up the great work! If I end up buying a GX550, I will keep this video in mind when thinking about modifications!
thank you for all your videos and information. Because of all your unbiased information I sold my 2023 tacoma trd off-road and bought a new jeep rubicon. Looking at all the heavily modified toyotas and offroad racing ultra 4 cars that use solid axle, I wanted to start my build with solid axles so i went with the wrangler rubicon. very happy and you helped make it happen thank you
Can you please do a review on the Nissan’s? Both the newer frontier and the older suv model. They’ve been picking up in sales since the Toyota recalls and I’d love to see newer makes on your channel.