Low Water Pressure Kitchen Faucet? Delta Leland Fixed 

I watched this video twice and fixed my faucet! Thank you, thank you, thank you!!!

Wife was ready to call a plumber to uninstall the newly installed Delta Alpen due to little to no pressure. Your video and 3 minutes of work fixed everything and saved us about $150. Thank you!

It worked on a newly installed similar Delta faucet. Greatly appreciated!!!

I have a similar delta faucet that I just installed and it started doing this almost immediatly. Had a hard time getting the old one out and got distracted, forgot to flush the lines before connecting new faucet. Tried getting ahold of Delta customer service, unsuccessful. Watched this video, went and took mine apart and found debris, Boom ! Thanx for the video post.

Thank you.. you just saved me a $150 plumber charge, and it took less than 5 minutes. I had just changed a water filter and suspected a blockage in the aerator, but couldn't figure out how to unscrew the head. Your video was very helpful and clear.

Thank you for this video! I have had low water pressure on my Leland for a few months and thought I had to replace it. Searched for remedies and found your video. Thanks for saving me a couple hundred bucks! water comes out now like a power washer, like new! Thanks!

Thanks for the video. We had a delta 9183 installed with new countertops three months ago. Flow was so bad that I figured I would have to replace the $600 faucet with a cheap one just to get some flow. Found your video and was pretty sure that wasn't my problem since the faucet was new, but what the heck, I took the head off, cleaned out a very small amount of grit and flow is easily doubled. Thank You.

Thank you for the clear instruction on how to unlatch and unscrew the head. Wasted time on other videos which did not show this important detail. My faucet clogged after I flushed my water heater tank. This solved the problem. Thanks.

Worked for me! Crazy how dirty and cruddy this faucet is brand new. World of difference after watching this video, thanks!

Thank you! Installed a brand new Leland in our kitchen today and experienced low pressure. Removed the spray head just like you showed us, and it was clogged full of gritty, carbon-ish stuff. Cleaned it out, and works great! Something else that you should check: My cold water pressure was still only half that of the hot. I removed and inspected the water supply valve from underneath the sink. It was badly corroded inside. Replaced it with a new valve, and pressure is now equal for hot and cold.

Thank you so much for this!! We had the exact same issue with low pressure and there was the same debris inside. My husband is so happy that he was able to fix it in less than 5 minutes!

Quick and to the point. Worked perfectly!

Thanks so much for the video. Had very low water pressure on my similar Delta faucet and was going to get a plumber to fix it. Cleaned the filter as you described and problem is gone. Saved the cost of the plumber. MUCH APPRECIATED!

Just installed new Delta Charmaine. Debris had it clogged from the start. This video saved the day! Thanks.

Big thanks!!! My wife has been nagging me for months to fix the slow flow and what I thought would be an expensive replacement cost was no more than 5 minutes of following your instructions and voila...the same black gunk was clogging the faucet. I won't say a thing to her but just let her be surprised this morning that one of the honey-dos is done. Thanks again.

Thank you!!! My sanity has been restored. I definitely would have let loose of the hose thank you for pointing that out! I just had the smallest amount of debris but now I am getting 100% more pressure.

Just did exactly as you said, success! Thank you so much!

I have a Delta Ashton Faucet and had little to no flow. I unscrewed my main lines to ensure I was getting pressure/flow from my manablock (great flow). I narrowed it down to my faucet. Not knowing or how to troubleshoot my faucet I typed in Delta Ashton Faucet troubleshoot. Your video popped up right away. I followed your instructions in unscrewing the faucet head. I removed the small screen with needle nose pliers, I used some air to blow off not only the screen but also blew compressed air into the faucet head. SUCCESS! I have my flow back, I was over thinking but my process of elimination and your video I'm all dialed in brother 👊🏽

Thank you!!!! This worked just great. I'm not used to doing any household repairs by myself, and oh my I am so proud to have fixed this, it was driving me nuts!

Had this exact problem, easy fix. thanks for the quick how-to.

Thank you so much for your awesome video!! This was the exact problem with my faucet too!

Worked like a charm on our same Leland kitchen faucet. Turned a trickle into a torrent in two minutes flat. Much thanks, guy!

Thanks for your video. I have a similar faucet from Delta & wasn't sure how to disconnect the head. Sure enough there was debris in there, picked it out and it flows nicely once again.

Thank-you for the video! I was able to clear the debris in the faucet handle and it works great again!

Just used your tip. Worked like a charm. Thanks for sharing

Thanks very much. Non-pro tip: If you're having difficulty keeping the tab pressed in and unscrewing at the same time, hold the tab in with some pliers, and you get a little leverage that way too.

Thank you! We were thinking we had valve problems! We have the Delta Savile and this video saved us time and money!

Thank you. I have the same faucet. It was full of calcium chloride crystals. Saved me 279 dollars.

Really appreciate the help

Tremendous help. Saved me a trip to HD to return a brand new faucet. Thank you.

Good quality video. No shaking. You may want to keep a strainer in place to catch any parts or tools from dropping down the drain. Once again. Good video, nice steady voice and instructions.

Thank you for the video. I had the same problem but it was not the same cause. I removed all the visible debris and it did not solve the problem. I watched several video and none of them tell how to get the in-side screen filter out. Mine had a little nipple sticking out in the middle of that screen so I used a pair of new needle nose pliers with good teeth. In my case the teeth were cross hatched. I grabbed the nipple and the screen came out easily. I couldn't see any daylight through the screen so I brushed it until daylight was visible. I replaced the screen and got perfection.

Worked perfectly. Thank you!

Simple fix, thank you for showing how to take off the head!

This worked for my Delta Charmaine. Thank you!

Quick and easy fix. Thank you so much!!!!

That totally fixed it! Thanks man!!! Awesome..

I love you! You just saved me $$$ by not having to call a plumber. THANK YOU!

Thanks so much! Super easy fix!

Huge help, for this non-plumber. Thank you.

Thank you for this vid! This was so easy to fix with your instructions. You got yourself a New subbie!

I viewed another video where the guy loosely tied the hose into a knot to make certain it didn't slip back. Good tip.

Thanks for the help!

Awesome...took 2 minut3s...THANK YOU!!

Thanks so much!!! This worked perfect for me!

Thank you Sir. This fixed my problem.

Yay!! Thank you!!! Your tip worked. I was so upset this new faucet less than a year old has already turned to garbage and I thought I needed a new one. I did exactly as you did and pulled out some black pieces of hard foam type material that was in 14 good sized pieces that I counted and some very small crumbs that I did not count. What is that ? Why is Delta putting those cheap pieces to break down so fast. Mine is no joke less than a year old the exact one pictured in your video. Anyway thank you it’s back to working and I’m happy we saved almost $400.00 having to replace it. Hopefully wherever those chunks came from doesn’t cause some secondary problems in the future. Thanks again and you had a new sub and 👍 from me.

Thank you so much! Your video was very helpful. Saved us a call to our plumber.

Thanks! I was able to fix mine!

fixed my problem in 5 minutes! thanks!

My hero. This solved my problem.

Oh, and even a fully-retracted hose can retract back on you... I usually loosely (but securely) tie the hose to the faucet itself with a piece of scrap towel or a rubber glove. At very least, drape a wet towel over the end of the hose to weigh it down to minimize the chance of it getting away from you.

That is it exactly! A big "thank you."

wow exactly my issue, MANY THANKS

Thanks for this awesome video, this helped me solve that exact problem.

You have just saved me hundreds of dollars by not having to call a plumber. THANK YOU!

Thanks a bunch

Thank you man!

Thanks for help on how to take off the head. Would like to know how to remove and clean the aerator due to hard water.

Thanks for the video - super helpful! I have a similar Delta model to yours that I installed a couple months ago, and it had nearly the EXACT same pieces of rubber inside it...same type and size...what are the odds? I am guessing this is could be a manufacturing issue with Delta if we experienced the exact same problem. In any case, thank you so much! Your video allowed me to fix my problem within a couple minutes.

How do you take apart the entire faucet head? My issue is that stuff got through that white screen and got stuck within the head. It never made it to the aerator in the front. So even when I take the head off and try and clean it the white piece on the inside it clean and the aerator on the opposite side is clean. But when I turn the water on when the head is off I get full pressure. When I put the head back on and turn the water on I get very low pressure. So the issue is something INSIDE the head. How do I take it apart?

I used a cloths pin to clamp on the hose to keep it from falling back under the sink

Thank you!!!!

Excellent video. Would you say that this also works on the delta VAROS kitchen faucet? We suddenly had the water pressure drop to just this Fossett in the house after someone has been working on the plumbing in the bathroom. Perhaps it’s a coincidence but hoping it’s an easy fix.

Thx man!

Saved my ass!!!! Thanks.

The black one with open hole ( looks like a part is missing in it?) looks different then the. Aerated one? How is it used for cleaning bowls? Which button to press to turn it on?

Was wondering if this is the same fix if only the hot water pressure is low. The water valves are both all the way on but only the hot water pressure is low

Tie a simple overhand knot in the hose and it won't slip down into the works. That's from the delta site tutorial.

What do I do if the hose went back up into the faucet???

Not the case. Remove nozzle and no presure on the hose, but we have good presure on the valves. Any other tip?

I installed a new one and the cold water pressure was fine but the hot water pressure is very weak. What could be the reason for this? Anybody experience this too?

Mine doesn’t have debris. Is there a slow flow filter inside on the Leland model?

My problem is that the cone around the power stream is clogged. You didn't go far enough.

wow

i always put a loose knot in my hose to keep from retracting

Not a fix for mine. Purged the lines before installing and still NO pressure until removing the head soon after install.

Dude! Kingpin Lounge T-shirt? Are you in New Orleans?

Kool like

Just saved me from calling a plumber. Good reminder to do the simple things first.

And what if that doesn't work? It helped a little bit, but not to full flow like yours did.

Thanks a bunch, worked like a charm. Please take my like + subscribe in thanks.

Thank you. The instructions I have don't say a thing about how to remove the spray head.

Thanks for the video. This faucet, unfortunately, is total junk! Worst I've ever owned.

Simple fix, thank you for showing how to take off the head!