I was writing a comment to flip the washer around right as you said “... you can flip the washer around to the other side...” Ha ha that was good. I had been tapping on the solenoid for weeks before it stopped doing “the trick” When I finally had to take the starter apart, I was quite pleasantly surprised to see that washer, knowing what an easy fix it was going to be. I also cleaned up the burnt side with a wire brush and emery cloth so I would have another good side for later. This was on a 1978 Dodge Power Wagon 360 gas engine, so who knows how many starters are out there with this easy fix... Great job, Thanks.
I don't think people understand what goes into making videos, answering questions from youtube and facebook, and all the other stuff Garrett does for absolutely free for the sake of the hobby. I sure wish he had been making videos 8 years ago when I bought my truck, back then you had to spend hours on steelsoldiers and if you ask a question that had already been asked get ready for a bunch of smart a## remarks.
I looked on your past videos and didn't see anything on the tires, I have a m35a2 and want to put bigger tires on it. I noticed that you kept the stock rims but did you keep the same size 9.00x 20. Would hope you make a video on the many options available and why you stayed with stock rims. Thanks, love you videos
My tires are 11.00R20 Goodyear G177 radials. Much better tire and a good bit larger. You can also fit 12.00R20 tires, and 365/85/20 fits well. I suggest staying away from 395s. Lots of people do run them, but they are too much tire for the truck. Very hard on the drivetrain components.
I bought a 24 volt delco style gear reduction starter and the bolt holes are 1/2" I have read a post on the steel soldiers forum that the starter studs are 5/8" just wanted to make sure. Thanks
Hi I have a M35A2 the problem I am haveing wen I am driving the speedo Gauge is only going up to, 15-20 mph even wen I am driving at 50 it just stays at that speed I have put the speedo cable on a drill and it's going up on the drill put it back on the Gearbox run the truck and it's running at 15-20 can any give me any advice wot could be doing this pleace
Same thing I told you on Facebook. It's more than likely that the cable liner is worn. You can remove the drive unit and take it apart to inspect it if you want, but they don't fail often. It's usually the cable or the speedometer itself.
Do you want it? I'll sell it cheap without the injector pump and turbo. If you do want it complete, there are a few options but I'm not giving it away. I can even include two new style headgaskets.
Hi . Mine works perfectly until engine gets warm , when it gets warm it dies without running rough or something . Do you know what could be the reason?
@@tacticalrepair installed a brake light switch on the air pack on air side after the pedal would get rock hard and lights would stay on wouldn't build any air pressure went over everything for air leaks found none then after about 2 hours of looking and checking the master cylinder pushed the fluid out of reservoir after that I had nothing filled and bled the hydro side of air pack but then found that it was letting air bypass to vent line with or without pressing the peddle with peddle not pressed less air/ with more I just bought the truck never owned on always wanted one so between my kids being into the whole monster big truck stuff and military truck I got it so I'm a little new to some of this 1970 Kaiser need some little stuff put back on and some replaced but from what I can tell nothing big
@@jamescain1306 so your air pack has failed and will need to be rebuilt or replaced. The smoke is because it is idling too much and not being driven. Cylinder temps are not high enough to completely burn the fuel.
Awesome yeah I drove it a good bit today it's actually building air today and holding to an extent where regulator is working for the first time since I bought the truck brake pedal is almost to floor when stopping but seems to be ok till I can get the rebuild kit looks like the short air pack for the clutch I'm probably going to change out when you put your foot on the peddle then push it about 4 to 6 inches it's released is that normal sorry I'm being a pest like I said I'm new and don't really know the norm of the truck I plan on redoing it just trying to get a list up so I can start picking things up any info and knowledge will be greatly appreciated thank you
Hey this might sound dumb, I want to get one of these as my first car.... any major engine problems I should be aware of. I'm pretty handy a starter is no big deal to me, but I hear head gaskets blow allot and they have runaway problems?
They're not too bad if you don't abuse them. Re- torque of the head studs helps avoid blowing headgaskets, and they don't run away unless you go into the injection pump and reassemble it improperly, or the turbo fails.
@@tacticalrepair hey, thanks for the reply what's a good rpm to keep them below and as far as top speed any way to regear them. Lots seem to put bigger wheels on but what about diff. Replacements or somthing
Run a taller tire like 11.00R20 or 12.00R20 radials. You can even step into singles like 14.5R20 or 365R20, however I advise against 395s as they damage the trucks. Too big. I also advise against single rear tires in general, but that is a personal choice most people make.
