Cody Do a burnout I built a k24 block k20 head Crx that i'm going to give to my dad on his birthday. He always loved the body of the CRX since it's light. I got one in awesome condition, Full interior stock and nothing broken or rattling .Going to throw on some ITB's and get it tuned.
Full Thottle He will gain HP and Torque with that turbo manifold because the collector is decent now, The one before the collectors were right aside eachother which is wrong.
I was watching some older videos and it sux how things change with fame. It was nice to see everyone enjoying working together and just doing the things they love. Seems like you're the only survivor through all this. I enjoy the videos and admire the things you have accomplished at such a young age. Keep up the great videos and I'll keep watching.
You’re 100% correct on that heat killing the stainless braided line. My oil feed line was around a MM away from the hot side of my turbo and burnt up from the inside out and had a nasty leak
just a little tip kyle, try use a different grade of stainless (like 316) as 304 ends to crack over time due to the heat cycles/work hardening and weight of the turbo. Just something to keep in mind for future manifolds, loving the fab youre doing just want to impart some wisdom. keep up the good work
MR KYLE YOU ARE A GREAT MAN THAT REALLY WORKS HARD ON YOUR VIDEOS AND ON TOP OF THAT YOU GO TO SCHOOL 2!! SO YOU HAVE A GREAT VALUE OF RESPECT FROM YOUR VIEWERS..KEEP UP THE GOOD WORK IN THIS CHANNEL..I LOVE YOUR WORK AND THE WAY YOU CONNECT YOUR SELF WITH THE AUTOMOTIVE WORK.....
I miss my Wago... But it saved my ass when i hit a cliff wall after swerving away from a moose. Also it was rusty as shit, and i still got the full 4wd setup (2 of them actually)
I would weld a tab on the side of the flange for the turbo on the collecter and then weld the other end to the exhaust flange that goes on the engine to help support the turbos weight
NICE! You need to hit up miller or Lincoln and get them to send you welders. As popular as you are I would bet they would send some awesome units to show on your channel.
You've cut a hole in everything else for exhaust! So just fucking send it and cut you a hole in the hood of 'er and let 'er rip tater chip!! Keep up the work man. I'm not an import guy and I really enjoy your videos. God bless
Damn Kyle, back at it again! Respect for finally clearing the air. Mad props on that turbo manifold. You should definitely tie it into the full exhaust.
Of course you didn't get any sugaring, you didn't get a full penetration weld, notice how you can still see the gap when looking at the joint, that means you didn't get a full penetration weld.
Just Drifting I doubt he would have too much issue with it cracking in the short term but in the long run he'll definitely be re-welding a few of those joints
I was about to go to sleep thinking “damn what’s the chance I sleep through a new boostedboiz upload” then I looked at my phone ready to stay a bit longer
Far better youtuber than anyone i follow. Always get cracking with bits and bobs and not just vlogging utterbullshit. Never stop and dont take your useless so called friend to heart. Much respect mate. 👍👍👍👍
I subbed to channel cause of how calm he talks and explains well and of course awsome fabricator thats what i love about this channel it makes me feel like i can do what he does but then realize shit never mind i cant
I would like to help ur channel, around the same time ur channel came around I was thinking of doing the same but just didn't have the motivation for it, so I just stuck to watching yours lol u keep it so simple it's the best. Great minds think alike.
a few suggestions for welding, possibly less of a bevel OR do a fill pass, the weld look like they have sunk in a bit, nothing major for the wago imo, but for the next one , other than that beautiful
I actually can't wait to get my own car and start showcasing my journey like Kyle and the other boys did, you guys encouraged me so much. I also love how you got working on the manifold straight away, keep it up broskee
Kyle, you should introduce us to your new camera man and helper! Even if he isn't permanent or something, would be nice to know who he is. Also would stop people from thinking it's Charlie. XD