Hey mate! Did you have to cut off this bucking side wing ? Or this chamber have special cut for it inside ? How does it work, I can't find any info about that
Maxx already squeezed the maximum from the AEG buckings with their M4A/P/E units. The M4G with GBB buckings just gives the chance for users to try their favorite sniper/GBB buckings. Someone may find the GBB setup to be more consistent and accurate compared to their AEG combo.
Ive been trying to get mine to work but it jams a lot and my nozzle stays stuck forward. Using a unicorn barrel, tried with 4UAD, ML silicone decepticon, Begadi, and LACC green bucking. All of them have done the same thing in my Kythera, my friends MCX kythera, and my KWA T10 AEG. Any tips?
I’ve bought the Maxx M4E and for me they are bad hop units, BBs are pushed too high into to the unit due to the wee concave space at the top they’ve made to keep the BBs in place, BBs are not sitting aligned with the nozzle that making a very inconsistent fps and side to side BBs flight. Tried to install it in different ways, AEG and HPA but still the same. You can hear the nozzle is struggling to push the BBs due to that concave hole design. Customer service seems to be dead as I’ve contacted them regarding this and no answer🤷🏻♂️.
Very strange. I've never experienced something like this in my tests. Quite opposite - i have very consistent bb placement in front of the nozzle and fps readings.
@@NikolayDimitrovFisher Thanks for your reply. Now I have fixed it, adding a stronger tappet plate spring from KOA made it very consistent 1-3 fps difference between shots.👍
Thanks for the footage. Do you have already an idea about Air consumption of the WOLF engine ? (How much Bbs at what PSI settings). Trying to compare to F2(Expecting that the WOLF will be lot better, since the nozzle is actuated by magnets and not by air), which yields +- 5500-6000 bb from 0.8l/3000 psi bottle @85 PSI with SFR regulator(until PSI in the tank drops below 85)
I don't have the exact numbers for bbs per PSI but noticed that WOLF is roughly 2 times more air efficient compared to my F2 all other things being equal.
Yes. Without cutting it you can't fit the bucking. And you need to sand a little from the X-Range lips so you can lock the C-clips. Modify bucking is ~16mm long. Maple Leaf buckings are 15.4 mm.
@@marcoviebrock1550 i wouldn't say it's noticeable that much to substantiate spending 90 EUR for it if you already have a good working combo. Definitely M4G shows more consistent FPS readings on chrono. Also with M4G and GBB buckings you have more predictable and flatter shots. IMHO the only AEG hopup combo that can compete with M4G is R-hoped barrel with flathoped Madbull 'red' in M4E. But R-hop is PITA for install and fine tuning.
No. It requires a unbridged barrel with AEG side cuts for the C-clip like Maple Leaf Crazy Jet, ML hybrid barrels or Stalker Morpheus. And it works only with GBB buckings.
@@danielarturodebernardogome832 in my MTW Maxx MGW with Stalker Morpheus and Stalker R-hop patch and sleeve bucking (or Flamingo) works better than any regular AEG bucking. I avoid recommending anything. I prefer to post my results and let everyone decide for themselves if they like them and would like to try something similar in their replica.
@@NikolayDimitrovFisher have been trying lately the 4UANTUM new aeg bucking. Getting pretty good results 7x7 cm grouping at 30M. Will be for sure trying what you told me, as I already have the m4g…