No video :(

MBMMLLC.com: Diesel powered rock crusher hammer mill crushing and grinding gold ore

Подписаться 314 тыс.

Просмотров 219 тыс.

50% 1

This is a demonstration for a client running a 12"x9" hammer mill dry with a 1 mm bar gap spacing. At the end of the video we show the results of the test using a screen sieve analysis. These mills are great for the small scale miner or prospector as they can be powered with gasoline or diesel motors for use in remote areas. They can process around 1000-1500 lbs/hr at 1 mm bar gap spacing and produce product which more than 50% passes a 50 mesh screen. This product is perfect for running directly onto a shaker table or sluice box for recovery. Check out some of our other videos on gold and precious metal recovery/processing on our RU-vid Channel here:
/ mbmmllc
Website: bit.ly/mbmmllc44
Thanks
** Video of a 16"x12" hammer mill running wet:
• Crushing And Grinding ...

Опубликовано:

23 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 85

@mbmmllc 10 лет назад

Ygmfmh- Under normal conditions we would use water and suggest it to all of our customers. This particular customer asked for a dry demonstration. If you stand up wind its not too bad, but would not recommend running like this for a long time. I have posted a link in the "about" section to a video of one of our hammer mills running wet and you will see there is no dust. It makes a great slurry to run directly on to a shaker table or down a sluice box! Thanks for the comment.

@gordonmccoy4537 5 лет назад

Glad you published this particular comment.... I WAS going to mention some severe lung problems in the future if not wearing a mask...

@edmondmkasian6173 5 лет назад

I am car mechanic, I have good suggestion for you If you wanna extended life of diesel or gasoline engine in such dusty working environment add two stage air cleaner that you can find on farm tractor first is dry separator with glass mushroom syclon and second is wet (oil) cleaner, Also its better you connect 3-4 inch flexible hose (like vacuum cleaner hose) and connect two stage air filter 2-3 yards away from engine, and you need to clean it each week,or 100 hours,

@mbmmllc 4 года назад

Great! Thanks!

@alexarriaza4016 3 дня назад

How long do your hammers last. What material are they made from?

@valkeren1 4 года назад

Gracias por mostrarnos su diseño . Es una excelente maquina. Solo veo una deficiencia en el diseño y es la cantidad de polvo que va directo al motor.

@mbmmllc 4 года назад

Thank you for your comment and for watching our videos!

@ricardomora692 4 месяца назад

Cuáles son las dimensiones del molino? Cuántas toneladas la hora puede triturar ?

@Teddy_Bass 7 лет назад

I bet you sell lots of these. Great product

@Moronicsmurf 7 лет назад

Would it be possible to construct one machine like this for breaking down not only pistons but engine heads, intake manifolds, parts of the block.. I need a way of recycling and breaking down aluminium to a 8-6 mesh powder before seperation and melting. =)

@mulengamulenga4197 2 года назад

This is great! How often to change the beaters?

@ronlewis2707 4 года назад

HOW much would like to purchase

@stevensamwel4854 3 года назад

Perfect

@jimmierturner3597 Год назад

Thanks!

@manusanthoshmanusanthosh8505 3 года назад

Sir is it possible to crush clam shell with this mill.if not could you suggest for any mill

@INFOWalla8805 Год назад

From which country is this machine can it be delivered in india

@abrahamventurajorge1940 18 дней назад

Hola, que precio tiene este equipo puesto puerto Santo Tomas de Castilla Guatemala..

@alexarriaza4016 3 дня назад

Nostros los fabricamos en Guatemala

@rogelioruiz9617 3 года назад

Good Day ! Please Do you can inform to me where I can get one of this and his cost? Thank you very much

@richardvincent7709 8 лет назад

Great product! However how did you break down or crush the initial stone sizes of approximately 150mm down to the 13 mm partical size that was crushed in this video?

@mbmmllc 8 лет назад

+Richard Vincent Thanks for the question. We used a jaw crusher. You can see a video of one of our jaw crushers here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-0bSmO9N25Yk.html Also please check out our website for more details: www.mbmmllc.com/

@minhtong5906 2 года назад

@@mbmmllc chào ngài tôi quan tâm sản phẩm này của ngài , tôi muốn đặt hàng bên ngài làm thế nào để liên lạc với ngài

@yhockievlog3733 Год назад

Magkanp pph yaan sir

@yassinmashautymashaury2734 2 года назад

Good. Could you give me the price of Engine powed hammer mill?.

@brandonsaunders6551 3 года назад

Is it spinning counter clockwise? Most I've seen spin clockwise and it creates a vacuum so no dust in your face it pumps it out the bottom

@douglaspohl1827 2 года назад

More important is the pulverized rock is being slug into the screen rather than armor hence the screen will prematurely wear to failure. Only a combo wet/dry hammer mill is a must. Dont forget armor wear plates unless you want the body to fail early.

@cabdulqaadir_cirro 2 года назад

Can it be used to grind sea salt??

@enterowilmer6213 4 года назад

How Mach the price of thet machine?

@Lexdex1111 4 года назад

wondering what to do with dust throw away sell may be .???? Fine sand dust material is it usable for any thing ???? Thank you in advance

@mbmmllc 4 года назад

dust is worth nothing

@FakhrurraziJasminur 3 месяца назад

how much cost ?

@daz41262010 2 года назад

super demo :)

@bryant5293 10 лет назад

What is the avg cost on this machine. Same setup? Is the -50 mesh equivalent to fine flour?

@mbmmllc 10 лет назад

Hi Bryan, If you can send me an email at MBMMLLC@gmail.com I can send you a full price list and info sheet on all our equipment and hammer mills. The 50 mesh minus was the smallest screen I had at the time of the test. There is a lot of material that is smaller than 50 mesh, too. Fine cooking flour is between 100 and 200 mesh for comparison. Thanks for posting.

@mohammedsaid1795 5 лет назад

Hello I want to know if we can grind the sand to obtain a very fine powder, and if you can make it to obtain a small quantity 50 to 100 kg.

@mbmmllc 4 года назад

Thank you for your comment and for watching our videos!

@jabbarshaikh509 Год назад

Price and how can we buy

@mauriciocampues9346 5 лет назад

Exelente trabajo se puede acer con material humedo y en viar los planos de esa maquina

@mbmmllc 4 года назад

Thank you for your comment and for watching our videos!

@murtazantimba4270 3 года назад

Were i can get it

@hcmv9433 4 года назад

this is exactly what im looking for!!! same size, same power, same use. International shipping? I want to export it to Mexico. Price? thx.

@mbmmllc 4 года назад

For pricing, please send us an email at Info@mbmmllc.com or call 360-595-4445 You can also visit our website here: mbmmllc.com/

@skeets6060 7 лет назад

Do we have a price on this little beast?

@mbmmllc 7 лет назад

Please email us at info@mbmmllc.com for more information on pricing and specifications.

@BadutA12 Месяц назад

Boleh juga

@iglianbilbili5816 7 лет назад

Mama mia perfeto

@carlosarielrodriguezferre9205 4 года назад

Hola, como lo tamizan para los distinos granos ???

@mbmmllc 4 года назад

Our mills are designed for rocks

@harrickvharrick3957 Год назад

Very impressive, although some other impressions are also hard to miss: That this is not an environmentally friendly method with regards to it producing dust as a final product AND as loads of fine particles in the air, and that it is not quite wise of the dudes operating the mill to not wear breathing protection..

@subconch7560 8 лет назад

bagaimana caranya agar saya dapat membeli alat tersebut?

@mbmmllc 8 лет назад

If you can send me an email at MBMMLLC@gmail.com I can send you a full price list and info sheet on all our equipment and hammer mills.

@anukoolminerals734 4 года назад

How much mesh it could make in hour sir...

@anukoolminerals734 4 года назад

Plz share Ur mobile number...

@mbmmllc 4 года назад

For pricing, please send us an email at Info@mbmmllc.com or call 360-595-4445 You can also visit our website here: mbmmllc.com/

@shivdutt4869 4 года назад

Whate is praise

@user-cx6qy1ei4p 3 года назад

Supper

@sugandairawan844 2 года назад

❤️

@madelgadod 10 лет назад

Tienes un representante en Perú, necesito uno

@mbmmllc 10 лет назад

Hello Cayajo- Please send us an email at MBMMLLC@gmail.com and we can discuss the details of getting you a machine shipped to Peru. I have a past customer / importer in Ecuador who may be able to handle all the shipping for you on the machine. Thanks, Jason