Mcculloch Chainsaw spark and oiler problems: Update

Подписаться 136 тыс.

Просмотров 56 тыс.

50% 1

goo.gl/wYri2L Click on link to order the PET-4000 intelligent spark tester. In this video, I give an update on a chainsaw that had a weak spark and would not run right. I also found the oiler did not work, so we take a look at that as well. Disclaimer:
Doublewide6 has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’s videos. Use this information at your own risk. Doublewide6 recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6. Please support Doublewide6 by donating to his Patreon Account / doublewide6

Опубликовано:

13 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@goodisnipr Год назад

This looks exactly like my saw. Mine isn't oiling either and I suspect a broken line in the oil tank. RU-vid is like being able to talk to Grandpa who knows absolutely everything about absolutely anything. Uploaders need to be protected at all costs. Thank you for your service.

@Garwood900 8 лет назад

Many thanks doublewide6 for this video. I have the same problem w/ my McCulloch 3216 not supplying oil to the chain. I followed your instruction, and it's working again. I also replaced all the fuel lines as they were brittle from age & the crappy 10% ethanol gas that's only available today. Have a great day!

@roycagle3646 6 лет назад

Heat and ethanol will destroy those tygon fuel lines like no tomorrow!

@buckwheat7424 8 лет назад

that's just so weird, I got a bunch of mccullochs saws. and the little one 3214 I changed the clutch gear, and new chain and bar, the fuel lines were toast so I changed those, and the oiler is working but kind of weak and bar oil leaks around the bottom. So went on youtube to see if I could find where the oil pump is. This video was the one to do the trick, at the same strange time, the kill button only works sometimes and sometimes it doesn't at all. This video is the one!

@thebrond2 8 лет назад

Hi, thanks for the video, I've been searching the web for info on the oiler and where it is on the mac cat 389. This helped a lot.

@jameslundy70 6 лет назад

Good video, I have the 2014 eager beaver saw and could not find a good video on the oil tank, I had a bad leak. But thanks to your video I found out what was wrong.

@Geordo1960 9 лет назад

Thanks for all you videos, good stuff.

@beechwood619 9 лет назад

Timber Wolf is correct, you explained the coil issue exactly in reverse. The spade lug on the coil should connect to the coil inside, not the ground.

@doublewide6 9 лет назад

beechwood619 Thanks for the tip. I usually don't check coils with a multimeter (either there is spark or there is not). This coil has spark, so I put the multimeter to it since it would not kill. Sounds like I may have been testing wrong with the meter. The kill wire goes to the switch and the switch goes to ground. I have continuity through all wires and the switch, so I don't know why it is not killing the engine. Any ideas?

@timfarris7704 8 лет назад

where did you get the line puller? Also what is it called exactly? Thanks!

@jimsworthow531 6 лет назад

Great video; it just helped me; thanks!

@flixyfn2454 4 года назад

I have a McCullough mini Mac not firing the call Will shock me when I put my finger in it but spark plug will not fire what is up with that I mean it shocked me real good but it won't spark a plug

@RobtJude 4 года назад

I Microwaved the lines for 10 seconds, they came out like spaghetti. Slipped right through the hole and right on to the fitting. Careful you don't burn them up 5-10 seconds in the Microwave is plenty.

@LRCohen1961 9 лет назад

Good video....thanks.

@ken4334 7 лет назад

mcculloch 480 chainsaw wont start at all .Can you give me some help please.

@Smalltechguy 7 лет назад

First thing is does the saw have spark? Does the saw have compression? Id the fuel making it from the tank into the carburetor?

@wtimber 9 лет назад

If the kill wire is connected to the grounded screws what is the other side of the kill switch connected to? is it possible that's backwards?

@doublewide6 9 лет назад

Timber Wolf Sounds like I may have been testing wrong with the meter. The kill wire goes to the switch and the switch goes to ground. I have continuity through all wires and the switch, so I don't know why it is not killing the engine.

@Geordo1960 9 лет назад

Those plastic lines are always a problem even on other appliances.

@mferrarorace 4 года назад

I have no luck with these saws. Coils, carbs, constantly repairing mine to the point where I spend more time repairing them than cutting wood. Should have just bought a stihl from the get go.