MERCEDES E CLASS W211/212 OUTER AND INNER TIE ROD REPLACEMENT!

Подписаться 7 тыс.

Просмотров 15 тыс.

50% 1

HELLO EVERYONE AND WELCOME TO A NEW HOW TO DO EPISODE.
IN TODAY'S EPISODE I WILL SHOW YOU HOW TO REPLACE THE INTERIOR AND EXTERIOR TIE RODS OF A MERCEDES E CLASS BETWEEN THE YEARS 2000/2015.
Disclaimer:
Due to factors beyond the control of HOWTODO, I cannot guarantee against improper use or unauthorized modifications of this information. HOWTODO assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. HOWTODO recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of HOWTODO, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not HOWTODO.

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@iglibleta2354 Месяц назад

Very good video and your explanation are perfect. Thanks for sharing

@HOWTODO0828 Месяц назад

Glad it was helpful!✌️

@BionicRusty 9 дней назад

Awesome video. 👍 Thank you for sharing 😊🙏

@HOWTODO0828 8 дней назад

Thanks for visiting🙏

@bofasofa9399 14 дней назад

Important point to remember: The torque spec for the nut on the ball-joint end of the outer tie rod is 50nm + 90 degrees after.

@HOWTODO0828 14 дней назад

Thank you for feedback 🙏

@jonnyboy2504 11 месяцев назад

I like your car. Good job on your video 👍

@HOWTODO0828 11 месяцев назад

Thank you! 👍🙏

@glennjones4723 Месяц назад

Thank you

@HOWTODO0828 Месяц назад

You're welcome✌️

@LH17578 10 месяцев назад

Great job

@HOWTODO0828 10 месяцев назад

Thank you 🙏

@TheSveinOlav 17 дней назад

Hello, and thank you for the great video. Can i ask, is it possible to do this job with the car in a normal garage, or do i need the canal/well to have enough space to get under the car?

@HOWTODO0828 17 дней назад

You can do it even în the parking lot. You just need a good jack and something to support the weight of the vehicle and that's it. Just follow my steps and you will be able to do it very easy. Good luck 🙏💪

@TheSveinOlav 16 дней назад

Can i ask another newbie question? How to jack the car up, and then place jackstands? The car have only one jack point on each side, and when i’ve jacked it up, there is no space for the jackstand, as the jack is taking up the point :p

@HOWTODO0828 16 дней назад

Good question. I always lift it from the nearest point to the jack point. And the. I have enough space to pus my jack right on the jack point made for this. In some cases you can bend some metal parts from underneath the car or you could brake the plastics from underneath due to heavy weight of the car. That's the risk of doing it yourself. Just be careful.

@TheSveinOlav 16 дней назад

Thanx! Yes, last time i jacked it up on stands i put the jack as close to the jack point as i could. It did some damage to the dust cover and the metal seam underneath. I just hope this wont induce rust problems or hurt the canals.

@HOWTODO0828 11 дней назад

You'll be fine sir.

@mygoalcrash8077 2 месяца назад

nice video! i have clicking noise when turning wheels is tie rod?

@HOWTODO0828 2 месяца назад

Yes it's the tire rod. My recommendation it's to replace the inner and outer tie rod just to be safe and just to make a verry good job on your car. Good luck mate 🙏

@mygoalcrash8077 2 месяца назад

@@HOWTODO0828 can it cose wheel shaking when braking? i already change discs and pads. .i think my wheel hubs is not straight to.

@HOWTODO0828 2 месяца назад

Yes it's can cause them to shake during braking and on heavy terrain

@DutchOrbit Месяц назад

Have you done the cross strut (forward control arm) I can’t get it back in the steering knuckle.

@HOWTODO0828 Месяц назад

Yes I did.

@DutchOrbit Месяц назад

@@HOWTODO0828 video?

@grygarek 7 месяцев назад

Hi, can I ask you, how did you jack up car ? middle jack point (rubber brick) you couldn`t use due to canal. So how did you placed jack stand on one side :-). I`m asking, because I have similar garage

@HOWTODO0828 7 месяцев назад

I have enough space for the Jack's on the sides, the canal it's not as wide as the car so I have atleast 25 cm on each side for the Jack's to be places under the car, and if you use a low profile hidraulic jack you could also place it at an angle and you'll fit it perfectly under any car. Hope it's helps 🙏

@johnparkerzabala 4 месяца назад

Very much obliged 🙏🫡

@HOWTODO0828 4 месяца назад

You're welcome 🙏

@esesmash7149 6 месяцев назад

How much did the parts cost you? I hit a curb last night and snapped from passenger side inner rod. Hoping I can fix it

@HOWTODO0828 6 месяцев назад

The parts are not so expensive, around 50 buck on both sides,you cand fix it very easy if you are able to do it yourself. Follow me and good luck

@Dnasty1 Год назад

Hey great vid. I just purchased some new tie rods off amazon from some no name company and they don't come with those little round metal discs that sit between the ball joint and the wheel hub. My oem ones had this and I was wondering do I need to put this ring on the new ones I ordered or do I just put the new tie rods on without that thing? I am not sure whta the ring does.

@HOWTODO0828 Год назад

You could put the old ones from the old tie rods just to be sure, some manufacturers don't put the entire kit with all the necessary parts and because of that you have to reuse some of the old parts wich you removed from the car.

@Dnasty1 Год назад

@@HOWTODO0828 oh ok I was not sure what these rings did so I left them off. Do you know what they do?