Mercedes Vito Fuel Feed Line Replacement

Подписаться 986

Просмотров 38 тыс.

50% 1

In this video the fuel feed line coming from the fuel pump to the filter is replaced. You can see; the replacement to the line, removal of the engine mount and the changing of the fuel filter.
Disclaimer:
Due to factors beyond the control of Box’s CarFix, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Box’s CarFix assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video's. Due to factors beyond the control of Box’s CarFix, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Box’s CarFix.

Опубликовано:

18 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@kev5847ify 3 года назад

Top video pal 👍Thanks

@CryptoMindsets07 3 года назад

Great video, very helpful. I have a question about fuel pump. My 2003 vito w638 doesn't have electric pump in fuel pump assembly. Is that normal, does vito 2003 come with Electric fuel pump in fuel tank. Thanks

@ahmedagha5605 3 года назад

Very good info.. thanks

@stephenwelby3618 4 года назад

If you save the fuel line you have taken off if the Clip is ok you can fill your filter put it on the too draw fuel into your filter

@terryjoker7655 7 лет назад

Thank you for the video. compared to others I have watched your focus is much better and clearer. I have just replaced the diesel filter on mine becuase my mechanic was worried he might break the clip on the hose you replaced. I used diesel from old filter to fill up new filter but due to slight spillages it did not fill to the top. Therefore I am guessing I now have air in the system and wondering how to bleed it. Cannot find a lift pump anywhere. Any quick ways to bleed it? Looks like there is a bleeding screw on the top of the filter, I have tried removing it and cranking the engine hoping to see diesel pump out but no luck with that so far. Not sure which of the hoses is the best one to release for bleeding. The one most left seems the obvious one as it will be the easiest and is probably also the highest point for air to escape. Any advice will be appreciated.

@BoxsCarFix 7 лет назад

Hi, I need a bit more info: what is the van currently doing? Is it not starting?

@terryjoker7655 7 лет назад

The van was running fine. I just removed the diesel filter and replaced it, but realise in hindsight I should have properly filled the diesel filter. After replacement, it started normally, then cut out about two seconds later. I continued cranking but no luck starting (yet). Dont want to over crank it Today I filled the filter to the top on the left side hose (the one that is like a metal a pipe extending out of the filter if there is nothing connected to the filter. Anyhow the battery has now started running flat so I need to put it on charge but cannot find my chargert anywhere. I have a jump box I have put on charge and will use instead until I find my chargert. So in short, yet is it not starting at the moment.

@terryjoker7655 7 лет назад

Was not starting, but after a bit more effort managed to get it running. Ran the battery flat and struggled to find my battery charger. Just when I found it and wanted to connect it up, I cranked it one more time giving full throttle and hey presto!! it started.

@BoxsCarFix 7 лет назад

Nice one, glad the problem is solved. Thanks for watching.

@abdulhakeemmwai5875 4 года назад

Thanks a lot good video... Really need help my w638 v230 wount rave at all.you start but it can't rave it in idling mode... I've computer box new.,fuel peddle, throttle all new nothing changed ideas

@BoxsCarFix 4 года назад

Hi Many Thanks for watching. Unfortunately, I don't have a clue, Ive seen ones that go into limp mode and wont rev over 3000rpm. Diagnostics might be the way to go. Thanks again.

@larkhill2119 4 года назад

They won't rev over 3000 if the clutch is depressed or the clutch switch faulty. Had me panic one day.

@zerocool6167 6 лет назад

Hi great video. Just a question would you be able just to change to plastic clip that goes into filter. Will bit of heat release clip and allow new one to ne fitted.

@BoxsCarFix 6 лет назад

Hi, No I dont think that you can, and I wouldnt do that. The lines are sold by merc altogether. And I would not be using heat on a fuel line. Thanks for watching.

@zerocool6167 6 лет назад

Hi, how long did job take you. Iv asked for price in garage and wanted to gauge for myself. Cheers

@BoxsCarFix 6 лет назад

Hi It took about an hour. Its not a complicated job. Thanks for watching.

@albertol.abrisqueta4324 6 лет назад

hey hi! first many thanks for the tutorial i just replace the line and all the orings and started first attemp awesome! I just wanted to ask u about the grinding noise when start the engine after the repair, i have the exact same noise and freaked out! is it normal? why is this happening? MAny thanks!

@BoxsCarFix 6 лет назад

Hi, Im not sure what noise you mean? Do you mean the starter motor noise? If so that is normal. Thanks for watching.

@albertol.abrisqueta4324 6 лет назад

Never mind.. i think it was just the engine mount settle in place The van still have some air after changing the feed line and the other 4 orings on the fuel lines, regulator orings, just missing the oring on the pressure sensor but someone told me this one would be leaking fuel if the seal was bad.. any suggestion? thanks!

@BoxsCarFix 6 лет назад

Hi. Yes I would expect to see a leak , but, if something is not in good order, needs replacing, is missing, is due for service or you see it as not fit for purpose, then it needs changing. Thanks for watching.

@jasonputtock4428 4 года назад

how to remove the filler neck please.???

@stephenwelby3618 4 года назад

I have replaced my filter and middle fuel line but still getting air in ??

@stephenwelby3618 4 года назад

By the way your video was brilliant

@jonesPossibly 5 лет назад

Hey - hows it going - great video. When you mention about a manual, which one do you use? I need a copy of a manual for the W638 CDI110

@BoxsCarFix 5 лет назад

Hi, I don't remember using a manual for this job, it was a while ago. There are some manuals available on eBay. Sorry, not to be much help. Thanks for watching.

@jonesPossibly 5 лет назад

@@BoxsCarFix how did you get the part number for the fuel line? I need the number for the other line that goes into the fuel pump. the one to the right and above the one you remove.

@BoxsCarFix 5 лет назад

@@jonesPossibly Hi I got the part number from the Merc Commercials Dealer, get them to send you a diagram of the fuel lines, they are normally very help full.

@dantheman3815 7 лет назад

hi, appreciate your video! what was the reason for changing the feed line? was it because the clip on the fuel filter was broken or did you have a problem starting the car? asking because my fuel filter clip is also broken thinking it may be the reason its hard to start its also quite loose on the fuel pump maybe air gets in the line?

@BoxsCarFix 7 лет назад

Hi It was replaced just because the clip was broken. The vehicle had no starting problems. I would not think that is your issue as I would expect a leak to be present. But with all vehicles you have to methodically diagnose what is wrong, not just swap parts. Starting issues - could be a number of things electrical, fuel, air, egr. Good luck finding issue, thanks for watching.

@philzambo 7 лет назад

That' some hassle to change a diesel pipe! Great video, very informative

@BoxsCarFix 7 лет назад

Its a Merc. Thanks very much for watching.

@glenfordspencer2373 7 лет назад

Hi there thanks for the Vid. What's the reason for changing this other than it was broken? Was the performance any different due to it breaking? Only asking as I've just purchased a Vito and mine a few times the engine has just dropped when I came to a halt at a junction. Turned back over after a couple attempts. Thinking Fuel Filter from research?

@BoxsCarFix 7 лет назад

Hi only reason was that it was broken. Yes it could be fuel, but also a number of other things; EGR for instance. Only way is to methodically diagnose it, but if you are gonna try a quick parts swap; fuel filters are cheap and wont hurt. But if it doesn't work, start diagnosing. Thanks very much for watching and good luck.