Buy this Metal shed today at www.ilikesheds.com Twitter: / ilikesheds Facebook: / ilikesheds Google Plus: plus.google.com/1000246728586... Leave a review: www.google.co.uk/search?q=iLi...
For me, the ideas in ru-vid.comUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.
Is the slightly raised OSB boards sufficient to prevent condensation inside the shed due to the concrete underneath being wet, presumably not having a Damp Proof Membrane underneath? Also worth pointing out that the base should be sealed along the bottom (before fixing to the concrete) to prevent water seeping in at the bottom
What's best flooring for comfortable heat and avoid mould, damp and water residue/dripping... What can I put on wallsand roof to keep warm and dry? Best amount of vents in the shed?
You guys are the only ones who visually show each step clearly! With the other videos, the parts are suddenly & magically there without seeing how it got there, lol! Anyway, Thank You🌹!!!
This video was exactly what I needed! We got our shed second-hand with no instructions at all. Not even sure what brand or model it is. But your video instructions were perfect, and we successfully assembled our shed.
I wish I'd watched this a few hours ago. Now I can spend an hour tomorrow morning undoing my mistakes then finish building it properly. (In my defense the instructions provided with the shed are appalling) Thanks for the upload, it's brilliantly clear.
I’ve just done one of these and what a nightmare working from the manual, I’ve completed it and all is fine until I close the doors! There is a gap at the bottom, if I hold them closed all is fine, and I guess if a padlock is in place all is ok, depending on the type of padlock, any suggestions?
I've just ordered a metal shed (Different Model) as the one I got also has a metal bottom fram like this one, is it ok to put wood on top When it's just on a concrete base like in the video? That's what I'm planning to do. Any advice will be great thanks.
Hello, thank you for your comment. As long as the concrete base is flat and level, you would be able to put a wooden base on the concrete. We would recommend that the wood is on bearers to elevate the base slightly and allow airflow underneath to prevent issues with rot or mould in the wood. We hope this helps - N
Thanks for the tutorial, much better than the silent one with the canned folk music. I like the way you used the needle noses to hold the nut. If only someone would invent a tool specifically for that purpose...... A sort of screwdriver for nuts or "nut-driver" (for lack of a better word) 😅
anyone else had issues with the back and side wall panels? Each panel has like a flat edge and a cornered edge so the one can overlap the other and prevent water coming in. There is no other way to mount them on the base frame bc of the predrilled holes. So now the back side has flat edges on both back panels, and the side panels both have cornered edges. For the side panels it doesnt matter but for the back you now have to connect 2 panels on that flat edge and thus water can come in. its just stupid!
3 hours between 2 people yeah right! Believe me unless you have built this one on numerous occasions you will be lucky to get it done in 5-6 hours and that’s a big if allow yourself and a friend 8 hours minimum
Interesting fact about this shed, remember the story of the 3 little pigs? it was actually meant to be the 4 Little Pigs, but the 4th younger pig built his house using one of these cheap Chinese sheds and the the wolf had him eaten before he had it assembled, obviously not suitable for children so they cut the story to the 3 Little Pigs, not to the mention the part about the wolf farting and blowing what the misfortune of a pig had managed to assembly a mile down the road leaving a large gaping hole in Little Red Riding Hood's head.
Started building my today with 2 helpers 6 hrs later still not complete The Instructions are not very clear, we also watched the video and stil couldnt fathom out some of the instructions .... We go again tomorrow to try and do the roof and doors. You need plenty of Patience (which i dont have)
I’m with you on this. Full day on Saturday and an hour out tonight and do you think I know how to put the bars up for the doors because the parts I gave don’t have holes for screwing it up…. Argh!!!!
So maybe I'm missing something? Why would you not build the base totally before you put the walls up? It makes more sense to because you can square it, Level it and not fight putting the lumber through the doors? Anyone know why it wouldn't work?
Hey I build these shed for a living 10 to 20 a week and that exactly what I do every time. I build the base with the floor kit and then put the plywood on before I attached the sheets. This stops the sheets from falling so you don't need someone holding them as you are screwing them in the frame. Provided no wind
Thanks for the video it helped me a lot because the instructions in the carton or not clear. The problem is the product I think they could do it much simple and they should for example assemble the door already in the factory. The edges are very sharp and you cannot have the gloves always because you don’t feel the little pieces ( screws and other little parts) in your hands and with your fingers. If I knew I would buy the same thing but in wood maybe or another ecological material because it this product is using very poor materials and too difficult to assemble.
@@iLikeSheds thanks for your reply but if I lock the handles together this makes no affect because you can slide the both doors to either the far left or far right .
@@Paul-mm9bq If the doors are on the runners correctly, it will not be possible to completely slide the doors to either side and therefore the doors will be secured - Natalie
Winner of a video, been searching for "how many foundation piers are needed?" for a while now, and I think this has helped. Ever heard of - Damkietor Nonpareil Dominion - (search on google ) ? It is an awesome one of a kind guide for building better sheds and woodworking minus the normal expense. Ive heard some amazing things about it and my mate got cool results with it.
Great video content! Excuse me for chiming in, I would love your initial thoughts. Have you ever tried - Mahorrla Wooden Paradise Method (should be on google have a look)? It is an awesome one off product for building better sheds and woodworking without the hard work. Ive heard some unbelievable things about it and my friend Sam at last got amazing success with it.
Well where do I start with this 1 🤔🤔🤔 o yes . Horrific . Spent 2 days with 3 people trying Yes trying to build this bearing in mind I’m an Ex royal engineer . This was just totally shite . Took it down and sent it back ., and it was there 14x 11 . Never Ever again. Sorry Billy oh .
@@SctonThrtn I don't know.you need 2 people. Can't do it on a windy day either. Have t done mine yet as I live in the Mediterranean and it's been far too hot......it's bloody raining today
This is a Lego for adults. £265 price of this paper metal shed on Wayfair but please don't buy this horrible metal box. This shed should come with a little guy for installation. 2 people job and 6 hours of hard labour ... not joking, next time when someone calls me to install this type of shed I will charge X2 the price of the shed. 1000 screws and the holes are not aligned properly.
I will advised you please don’t do it you will be disappointed ☹️ if you can return it do it as fast as you can this product is nothing but garbage 🗑 I’m very handy when it comes to problems like this shed main problem should be done with one person no two but the engineers never thought about this little issue so the rest of problems are due to lock of imagination
If what you say is true, is that really enough for such an atrocity? Maybe his license and privileges should be taken away and forced to pay restitution to everyone he has harmed.; his children and children's children should be shunned by society and must agree to verbally rebuke him to even purchase basic necessities. The headstones of his ancestors should be removed and their grave plots left unattended to. We should also forbid his name to be uttered and place a prohibition on giving an infant the name. Those that presently share the name shall be given new identity and if the name is insinuated the speaker shall follow up by spitting. That enough?
Agreed... I've just had to fix up a £500+ outsunny ! For this price they could of put an electric screwdriver in with that pack but no! The shed is structurally weak it could be cut with a tin opener with ease. Also had to work on unleveled ground 😭
what a rip-off. a tin shed so thin you can almost see through it. it.s a joke out of a Christmas cracker. people are so gullible these days. these sheds are cold wet and noisy Metal shed used to be three times as thick, you could use them as bomb shelters and a fraction of the price. I will never buy another one of these pretty painted lumps of scrap ever again.
