MF135 6 Speed Restoration #44 How to Remove Your Hydraulic Lift Cover 

Excellent, this was exactly what I needed and covered all the steps from the shop manual that had me scratching my head. Thanks

Thank you for this great video series. It has been a fantastic resource and help tinkering with my MF 148.

This is easier to watch, than to try and read the manual for the disassembly process. With the problem I have(mentioned in my recent email about my 230) I believe I first need to drain the oil down far enough to remove the right side cover, with the response control, to see if my roller is in place properly. Thanks for your videos and help.

What a wonderful teacher you are Lance I have a 6 speed 135 which I use for road runs & shows.I may be 74 but I am learning more from you than out of a manual. I also enjoy your machining. I used to have access to a lathe & milling machine. THANKS.

Very good I have to free up the levers on my mf 230, nice to know about that roller, thanks for that one!

Excellent video! Keep up the good work!

thanks for ur video sir.

It's nice to know about that roller and how easy it is to remove to avoid bending the rod. I sometimes tug on things that don't move like I think they should and would have bent that rod for sure.

I have the correct tool for removing these covers and, in fact, they hinge over backwards and have a leg bolted onto the seat studs, all works very nicely.

Great video. I have a lift issue where the lower lift arms won't go down far enough on a 66 UK 135, otherwise lift is raising and lowering ok. Can I adjust the bottom screw at 9:12 to make the lift arms go down further? Lift needs to drop maybe another 6 inches. I have no pressure control, just draft & position.

Muito bom

Lift works when tractor gets warm lift slow raising back to up position

Mr. Bundy...in the first segment of this video I see your draft and position control and I just noticed that your position control plate is backwards...at least compared to my MF 20 Industrial. Even the label on the plate seems to indicate this with the up position being labeled as down. Shouldn't the two concave sides face each other? Thanks for the video...I'm about to tackle this myself!

Lance, I have a UK 135 that when I use the hydraulics the pump is pulsating even shakes the tractor while it has a load on it. Any Ideas, thanks

HI, great video series. I have an MF250. The rear lift arms are not responding to the controls. They lift when I first start the tractor (in the transport postion), but if I lower them, they will not lift again until I switch off the tractor, wait a few minutes, then start it again in the transport position. If I put an implement on the back, the lift is very slow and juddery but still will not respond to the lift control. What could be the cause?

WTF Lance, First time I've seen you use a rattle gun. Are you in a hurry or trying to hide the creaking shed noise. Love your vids and safety thongs. All the best and keep up the excellent work. Huey

Audio level issues. 11:00 Levels jump up (to where I believe they should be). 12:00 Drop back down (to levels that I believe are lower than they should). I've noticed on the last few videos the levels all seem to be to low. At that 11:00 minute mark I can hear the details of the shop, but nothing is obnoxious. I expect to hear the shed, foot steps, etc. Hope that helps so you have some specific spots to see the differences in those levels.

Wondering if you have any idea why my Massey 245 lift arms stutter when lifting. They lift fast and strong and go down smooth but they just have this tremble while going up. I removed the Lift Pump, stripped it down completely, immaculately cleaned it, replaced all oring's and back up washers, new piston rings, new pressure relief valve, fresh new Permatran 3 oil in the sump and it made no difference at all. All the pump parts that I didn't replace looked to be in great shape. The tractor only has 1000 hrs and has been always stored inside. No rust on anything. Now I'm unsure where to go from here. I feel like it should lift buttery smooth. Could it be the lift cover? Also the lift arms do not leak down when left overnight or longer. I'm stumped Sir. Wondering if you have any ideas? Any help would be greatly appreciated.

HELLO BY MR BUNDY BEARS SHET USE PLOW..WHICH ARM SHOULD BE USED? SLOW OR FAST ARM

Does anyone know what size allen wrench works for the screw on the right side cover?

hello my lift of my mf 135 does not want to drop just if it is weight. anyone have an idea??

Primo una pregunta

Must be early gray types of ferguson that..

Hi lance I think you need to normalise the audio take a look at ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Rj7sbBng-T8.html otherwise good start 🤛