Microwave Turntable Not Spinning - How to Troubleshoot and Repair

Подписаться 813

Просмотров 28 тыс.

50% 1

Troubleshoot and repair a broken microwave turntable that is not spinning
21V Microwave Motor - amzn.to/3NHuRxM
Handheld Oscilloscope - amzn.to/3PLOnuv
Hand Held Multi meter: amzn.to/31oWWUm
Impact Driver: amzn.to/3lKfGb7
Do not run a microwave without any covers off as they might be providing protection from microwave radiation!
I am not a licensed electrician. If you are not qualified, take great care when testing something that is powered on . Try to test object while they are off and make sure you test everything to make sure it is off before touching it. Injury or death can result from touching household power. This video is for entertainment to show you how I fixed my problem.
This is the model number of my microwave: JVM6175SF1SS. However, this process should work for other microwaves.
Super useful things in my toolbox:
Thermal Camera: amzn.to/2O1ThZr
Best 5 min epoxy - I use it a lot: amzn.to/3flU8iU
Recording Gear:
Main Camera: amzn.to/3sUkixN
External Mic: amzn.to/2Y5YMYk
Mic Adapter: amzn.to/3iyGrg6
Case to hold external Mic and Phone: amzn.to/3iB6zH5
Check out my website: www.stephenofalltrades.com/
DISCLAIMER Most of the product links are Amazon affiliate links, where I earn a small commission if you decide to purchase an item at no cost to you. Thanks for watching!

Хобби

Опубликовано:

26 май 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 8

@sofroniocarranza6064 2 месяца назад

Thank you sir

@tedlofland3446 5 месяцев назад

Those synchronous motors can be taken apart. The low voltage one you have has plastic gears in it that could be broken or the shaft that goes through the magnet could be corroded and just needs cleaned and re-lubed.

@paulthompson1216 2 месяца назад

So I tested the lead and it was about 24 volts ac. I put the continuity tester leads on and got nothing on both old and new motor. My understanding is that it should beep for continuity. New motor also bad maybe?

@jbird0713 3 месяца назад

I have this same microwave and I'm struggling to get the door off the hinges to clean some condensation streaks/stains between the glass panels. It's the same model as yours. When I try to lift the door up, there is resistance and the pins don't clear their holes. It looks like there is a black plastic piece below the top hinge on the door preventing me from being able to lift it straight up like other models (I've watched a lot of RU-vid videos on this). Can you help me? Do I need to remove that piece, or that entire plastic frame, first - before attempting to lift the door off? Or am I just not giving it enough muscle?

@jimprior5700 18 дней назад

Ossillascope is little bit of overkill don't yo think.?

@rogerfaust2239 Месяц назад

My spindle that turns the table has gotten loose. How to tighten it

@justinchang2601 6 месяцев назад

My whirlpool microwave has the 120v motor, I purchaseed this 21 V motor,, it started turning again. but after 30 seconds of turning it fully stopped again.. do you happeend to know the reason?

@stephenofalltrades1422 6 месяцев назад

If the original motor is a 120V motor, that means that 120 Volts is going to that motor for operation. If you put a motor that is rated for only 21 volt operation, it is not surprising that it blew the motor. You need a motor that is designed for 120 volts.