MK7 GTI VWR Lowering Spring DIY (How to) Install

Подписаться 395 тыс.

Просмотров 353 тыс.

50% 1

This video will walk you through the process of removing and install aftermarket lowering springs on your MK7 Golf or GTI. Due to technical difficulties we were unable to film the re-installation of the suspension, but it installs exactly inverse of the removal.
More info about MK7 GTI Springs
Items Featured in this video:
VWR (Racingline) Sport Springs for MK7 GTI:
www.shopdap.com/mk7-gti-vwr-s...
Neuspeed Sport Springs for MK7 GTI:
www.shopdap.com/55-70-07.html
APR Sport Springs for MK7 GTI:
www.shopdap.com/apr-roll-cont...
H&R Sport Springs for MK7 GTI:
www.shopdap.com/h-r-2015-2017...
Complete Suspension Install Kit for MK7
www.shopdap.com/complete-susp...
Ultimate Suspension Install Kit for MK7/MK8 (non DCC)
www.shopdap.com/ultimate-susp...
Ultimate Suspension Install Kit for MK7/MK8 (DCC)
www.shopdap.com/ultimate-susp...
Volkswagen Magnetic Bolt Tray:
www.shopdap.com/vw-magnetic-b...
Optional Replacement Parts (recommended for vehicles with higher mileage)
Replacement OEM Strut Mount
www.shopdap.com/5q0-412-331-e...
Replacement Aftermarket Strut Mount
www.shopdap.com/strut-mounts....
Replacement OEM Strut Bearing
www.shopdap.com/5q0-412-249-e...
Replacement OEM Front Bump Stops
www.shopdap.com/1k0-412-303-f...
Replacement OEM Front Dust Boot
www.shopdap.com/5q0-413-175-c...
Replacement OEM Front Spring Isolator
www.shopdap.com/5qm412545-vw-...
Replacement OEM Rear Upper Spring Isolator
www.shopdap.com/5q0-512-149-f...
Replacement OEM Rear Lower Spring Isolator
www.shopdap.com/5q0-512-297-d...
Shop for VW and Audi Parts Here
shopdap.com
----------------------------------------------------
VW AUDI Specialty Repair Cornelius NC
www.daprepair.com/vw-repair-c...
VW AUDI Specialty Repair Kent Ohio
www.daprepair.com/vw-repair-a...
----------------------------------------------------
More info on DAP Reward Credit
shopdap.com/store/rewardpoint...
Disclaimer: Please note all DIY are intended for basic information. Deutsche Auto Parts is not liable for any damage incurred during any attempt to follow the information shown in the video above.

Авто/Мото

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 317

@paulwiest8167 8 лет назад

To all DIY guys. When removing the spring on the the front of the car on the passenger side , the axle recedes quite a lot further under the car and is near impossible to reach without crawling underneath your car. Also, the axle limited how far down I could drops the breaks to pull out the strut assembly. It helps a lot if your remove the heat shield covering part of the axle where you removed the 10 mm triple square screws. Only by doing so did I free enough play to remove the strut. On the subject of replacing bolts and other parts of the strut assembly, I am nearing 15,000 miles on my car and replaced nothing but the old springs with the VWR's, not recommending this but I will report back for any issues, or if I die due to suspension failure I told my girlfriend that my only wish in death is for her to report back to this video and inform all my fellow VW enthusiasts of my demise.

@jasonvoorhees3666 8 лет назад

Why would bolts need to be replaced? Thanks

@paulwiest8167 8 лет назад

***** The bolts are torque to yield, when torqued down all the way the threads stretch, technically they are a one time use

@cdougyfresh 7 лет назад

going to attempt this install tomorrow with a lift, and a buddy who works at a subaru shop. Hopefully we won't run into too many issues. Will report back!

@allengonzalez2733 6 лет назад

Collin Douglas what happened

@anewto 5 лет назад

@@allengonzalez2733 If i had a dollar for every time someone said "will report back" haha

@recipioct 4 года назад

3 tips: 1. You can remove the strut without messing with the axle. You just need a good spring compressor to compress the spring while it's on the car. You may need to create spacers for it by cutting a pipe(I did). 2. You can make your own special tool to remove the strut by buying a large torx(45 or 55? I forget what I bought) bit and grinding it down. 3. make sure both sides of the front are on jacks or the sway bar won't come out. I just did this and am passing this info along because had I known the above I would have saved myself 7 hours of misery.

@deetailing 6 лет назад

Thanks and well done for the torque settings. Exactly how it should be done and no one seems to point out how to professionally put these things back together again

@jonnybonny4193 3 месяца назад

that 100nm bolt should NOT be done to 100nm, check your workshop manual people! It's 40nm + 45 degrees

@TOOL1023 8 лет назад

Great Video! Thanks for these instructions. I honestly believe I could do this myself now. Thanks again.

@JacobFrey 10 лет назад

Excellent video - such a great service to DIY and VW enthusiasts. Thank you!

@williamstadelmann1643 3 года назад

Never worked on suspension before but I was able to do the whole job in a day! Thanks !!

@zosqq 3 года назад

i envy you, it’s taken me 6 hours my first day🤦🏽‍♂️ shooting for less than 2 hours tomorrow

@williamstadelmann1643 3 года назад

@@zosqq it’s definitely a challenge but you look so cool scraping over speed bumps 😂

@audiwankenobi361 4 года назад

Thanks! I just did Eibach lowering springs and a Eibach rear sway bar and your videos are what i followed.... I started out by myself but getting the front struts back into the hub is pretty much impossible by yourself.... My wife helped me,mission accomplished.

@NoisyIslands 2 года назад

Did you cut the bump stop? If not, were there any issues? I just ordered some Eibach springs

@audiwankenobi361 2 года назад

@@NoisyIslands didn't have to cut anything....the only issue was that my suspension got really noisy.... I think that the bushings need to be replaced now....I still have the car.

@mihaistefanescu1999 9 месяцев назад

In One hand i have the strut and with the other i put the 3 bolts on top,Easy but you Need to practice

@n3tfury Месяц назад

@@audiwankenobi361 sway bar bushings?

@audiwankenobi361 Месяц назад

@@n3tfury Yes. Those too.

@2of2DCH 8 лет назад

Appreciate your efforts on these videos, and it felt to good supporting by DAP by ordering my Driver Gear springs from you all today.

@Deutscheautoparts 8 лет назад

+2of2DCH thank you so much for watching, I'm so glad our videos are helpful. Also I really appreciate the purchase very much. I hope to continue to earn your business. Paul

@2of2DCH 8 лет назад

BTW is the 100Nm torque spec @ 12:46 accurate for the lower ball joint? On your Basic Suspension Install Kit for MK7 it shows 40 Nm + 45 °.

@xxslipknotxx555 2 года назад

Great info and vid unless ur ready to get down and dirty you can do it with a friend but make sure u have everything! a block of wood helped me squeeze it out along with a proper bracket spacer (1000%) and yea good luck everyone

@masonrobbie97 6 лет назад

Just did this myself not as easy as it looks but happy with the drop. Keep in mind you need to pry the nuckle with something to even be able to fit the ratchet in there and yeah passenger side is a bit harder to do. Took me 5 hours since i took my time on it. Now that ive done it i feel i can do it in about 2 hours. Thanks for the video man would not attept it without. You also dont need spring compressors i just impacted them off then done!!!

@jmccann6735 7 месяцев назад

Bro you just loosened the strut bolt?? Lucky you're still with us 😂

@john-henrycorbett2647 7 лет назад

Thanks for the awesome vid Paul. Did my VWR spring install on my S3 last night and turned out awesome. On the S3 and probably the G7R it's not necessary to loosen the axle, had just enough movement to remove the shock assembly.

@john-henrycorbett2647 7 лет назад

+Deutsche Auto Parts wanted some advice.. I have a knocking noise coming from the front of the car when driving at slow speeds and maneuvering (while parking). Initially thought it was the old strut bushings and bearings so replaced them (together with new bolts and buts, all OEM) but still get the noise. Any recommendations and thanks for all the great content.

@mr_shake4480 3 года назад

Ball joint nut torque is 40nm+45 degrees. I tried to do 100nm as this video instructed and sheered the bolt.

@alberthuynh 4 года назад

This video was very helpful. Thank you

@holloWmanVid01 9 лет назад

Nice video with good informations

@Deutscheautoparts 9 лет назад

@julian UK. Yes you should always align the vehicle after the suspension has been taken apart.

@berkburak 11 месяцев назад

Thanks for the video! It will come in handy soon, when i will be changing my rear shock absorbers and coils. I have a Skoda Octavia 4*4 , 2015 years model. According to workshop manual so the rear bottom control arm bolt should the toghtened to 70 Nm plus 180 degrees, same as the bottom shock absorber bolt. 130 Nm plus 180 degrees is for the upper control arm bolt.

@solobellimino2356 7 лет назад

your video was of great help thank you.

@JimMadden 6 лет назад

So on a mk7 golf r with 17,500KM on it, what hardware would you recommend replacing? Great video! I’m having my guys at work do it, but it’s an Audi dealership so they want to make sure everything is done and replaced as needed.

@davidheether1655 9 лет назад

The only question I have really is about the inner axle bolts. So there is 6 you pull and then gives you some room to drop the lower control arm from the strut. When those bolts are removed does the axle drop out of the transmission? When putting everything back together is there anything special to do to get the axle back in if it drops out? Also should those 6 bolts each side be replaced?

@kanathea Год назад

perfect diy, huge props

@xenyyrockkstar 7 лет назад

I have a mk7 GTI with 50k kms on. would you suggest me for replacing strut mounts and bearing upon replacing springs?

@RaytheonNublinski 8 лет назад

I'm amazed that people do this type of work in their driveway.

@cristianzaharia9702 8 лет назад

Was wondering if i can use these springs for 2016 golf golf sportwagen 1.8 tsi

@jacksonzhang5885 4 года назад

What is the size of the tripe square that you used, I think it will be great if you can make a list of tools. Thank you

@BufiniPinoy 8 лет назад

had a pair of Koni shocks installed. when up on a lift it looks as though same side front shocks were installed due to the asymmetrical attachment of the end links. Is this normal?

@NileshParmar 8 лет назад

Great video. Please could we see a video on how to get a parking sensor wire from the engine bay to the inside drivers side on a vw golf mk6.

@gauchegaucho 4 года назад

Do you have the torque spec for strut bolt or just torque it as much as you can? thanks

@onetobum 3 года назад

need some advice fitted my h&r springs and new bilstein shocks. got to the drivers side and can't get the shock to sit all the way to the bottom of the knuckle, got about 3mm to go, but can't fit the pinch bolt because of strut alignment bracket. I have used the strut splitter. the passengers side was the same but reversed off a kerb and the weight of the car drop it into place and I could fit pinch bolt. I cleaned all the knuckle out before fitting the shock? any advice would be great thankyou.

@berto371rr 5 лет назад

Will it be pretty much the same on 2016 VW GLI to install these. Just picked up same set

@TheMessyGiraffe 6 лет назад

Is this similar to an install on a mk7 TDI? Factoring in the rear beam axle?

@jackwilliams5483 3 года назад

Should a dsg car be in nuetral when turning drive shaft to remove the bolts?

@TheCipotemasloco 9 лет назад

After I watch this video I when to the VW dealer and ask if they could do it and they said yes and they have the parts too .. I'm just gonna let the professional do it for me.! 😄 thks for the video !!

@Deutscheautoparts 9 лет назад

El Chero We understand. Springs may not be a DIY for everyone, we are glad the video helped you make a decision on if this install was for you.

@TheCipotemasloco 9 лет назад

Awesome video thks for the tips.!!:)👍🏻

@Deutscheautoparts 9 лет назад

El Chero No problem thanks for check it out. Please let us know if we can ever help with any of your parts needs.

@robertshetsen8691 7 лет назад

hey question I have golf r 2015 no DCC will be springs be better for my golf or I already have good springs I mean better than gti mk7

@rmc5278 Год назад

for the rear bolt torque settings . Did you use vw's torque to yield or upgraded bolts ? thanks.

@jeffsan8343 5 лет назад

Wow it looks awesome, how does the drop affect your headlights?

@Jeepyboyzoowap 3 года назад

Have you guys experienced any clunk noises after at full turn? Also suspension is creaking abit too when I go on the sidewalk side ways any advise will help me !

@ericmcfarland4228 6 лет назад

What springs would you recommend with 19 inch wheels and 40 series tire?

@slayednpked1 4 года назад

When removing the axle on the mk7s, are you supposed to re use, or replace the bolts?

@joshuagreen9666 6 лет назад

Did you have to replace any of the bolts? I have heard that they are stretch bolts..

@jasonvoorhees3666 8 лет назад

Do you have to torque the top three nuts on the front? And does anyone know what the torque spec is for the axle bolt? Thanks

@audiwankenobi361 4 года назад

Just wondering: why wouldn't taking the hub bolt off be the better option instead of the rear axle bolts?

@s4ur950 9 лет назад

How much do you think labor is for this? And don't you need alignment afterwards?

@ivanvega2821 6 лет назад

Would his he the same for a 2018 Passat R line??

@julianuk3266 9 лет назад

Hi again, I'm about to do this install this weekend. Should I be replacing any bolts or am i ok to reuse everything? My MKVII Gti only has 200miles on it.

@mustafahussaini2714 6 лет назад

how much lower did it bring the car down and did it affect the ride comfort much? i'm a bit concerned with ride comfort :/ But it 100% looks better (Y)

@thomaschung7377 8 лет назад

what is the torque spec on the 13mm strut tower bolts?

@luisrc.3637 3 года назад

My MK7 is currently at 75k miles and I will be installing VWRS should I replace my Strout mount/ strout bearings? Thanks

@alanbolanon2635 8 лет назад

man... did this today. was alot harder for me than how you made it look... lol

@Deutscheautoparts 8 лет назад

+Alan Bolanon Glad it was helpful. Its not as easy for sure.

@marksaltpaw3194 8 лет назад

Great video, very informative! When you pulled the axle from the engine, did you have to spline anything back in?

@prs314 4 года назад

I am not sure 14:27 is correct. Transverse Link, Multi-Link Suspension, FWD and AWD pages in the repair manual for Golf 2015+ specify this bolt as 70 Nm +180° not as 130 Nm +180°. Did they change the specs?

@dBsdecibels 7 лет назад

Would there be an extra step or two for DCC equipped vehicles? Does the DCC damper plug into the car and need to be un/plugged?

@erikwahr8454 4 года назад

dBsdecibels unplug the little sensors and made sure the leveler arm things are not connected (little green arm that attaches with a ball joint)

@goyparlearntorideschool3233 Год назад

My 2017 gti, has a stability sensor attached to the left rear control arm. If you have that, make sure to disconnect that before you drop it.

@fernandohurtado2940 4 года назад

good video thanks guy after doing the lowering springs swap I took it for a drive around the block the epc light came would you guys know why. 2018 gti with 13000 miles on it

@coreytelfer4566 4 года назад

Do you have adjustable suspension?

@brianwilhelm9464 3 года назад

Can you confirm the front 3 ball joint 16mm torque specs? Video says 100nm, shopDap site has 40nm plus 45degree. Vw golf repair doc seems to line up with the 40nm plus 45 degree. Don’t want to snap anything going to 100nm, but don’t want anything severely undertorqued

@jasonvoorhees3666 8 лет назад

Great video but when you reinstall the front strut assembly how do you get it back in the knuckle if it's such a tight squeeze and how do you know when it's in far enough? Thanks

@iiiDrum 8 лет назад

Shit sucks. I actually stopped the install when I was doing it because it took me an hour just to pry the knuckle off the strut. I cant imagine putting it back on.

@johnk5003 8 лет назад

Is the process the same for a MK7 R? e.g. same equipment, torque specs, procedure etc. Thanks for the video, really helpful!

@araxtypesh 8 лет назад

The torque specs noted here are different than those listed on your website (for the suspension bolt kit). Which one is accurate?

@nofaithjusthope8714 6 лет назад

Drew Skez...He asked a legitimate question and you give smart ass reply, what's wrong with people like you? I see this same sort of smart ass commenting on vwvortex ALL the time. DAP web site does indeed have differing torque specs for some of these stretch bolts the question still is unanswered.

@RJYOUNG396 Год назад

I've only found one video that shows the passenger side being taken out and he was doing a different method. Is the passenger side really hard or really easy, why is it left out? I need to know how to do ALL four corners!

@dvandentop 2 года назад

what size triple squares needed?

@GOODSATIVA 4 года назад

Why were mine grey not blue I got the same exact ones but they just came in a different color

@bobtroutman 8 лет назад

Are there any additional parts (control arms, endlinks, etc...) needed to straighten the alignment of the car out once it has been lowered?

@Deutscheautoparts 8 лет назад

no you will not need anything like that when installing these springs.

@kentowers2802 5 лет назад

Hi - thanks for the video - very useful Is it worth replacing the top mounts and bearings on a 9000 mile car? If so Is it worth upgrading to Audi TT items? Thanks

@lory001 8 лет назад

Hi, great video. In a few days I'm trying to change the original springs on my car with an Eibach Pro-kit springs. I've only a few question: I don't have an air impact wrench so I've to do everything with a torque wrench, is it possible in your opinion? Which is the correct torque to tighten the upper bolt of front suspension? And the last one: which is the right measure of the triple square set that you use to unlock the six screws of the drive shaft? I'm sorry for my poor english, hope you understand. Thanks a lot!

@Deutscheautoparts 8 лет назад

+Lorenzo Longo Take a look here for the strut top hand tool info. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hR0MmvogT2A.html

@lory001 8 лет назад

+Deutsche Auto Parts Thank you very much again. I've one other question: wich is the size of XZN (triple square) that you use to unscrew the six screws of the drive shaft? Is possibile to unmount the front suspension without unlock the drive shaft?

@benjaminvisbeen5113 3 года назад

what kinda torque wrench do you need

@s4alexis 9 лет назад

Think this would be the same for an e-Golf install? Also, I what is the torque setting for the nut on the top strut mount on the front? You just did a few runs with the air wrench and didn't torque it.

@Deutscheautoparts 9 лет назад

Alex Moreno Probably so but we have not gotten under an e-Golf yet

@G37Samer 9 лет назад

Hey guys at Deutsche, I installed these springs a couple of weeks ago and I've been hearing a lot of squeaking noise. It's coming from my front passengers side whenever I drive and when I make right turns. I brought it into my friends garage and we checked to make sure everything was tightened down properly and that it was safe to drive. Everything checked out fine but the noise still persists. Any thoughts?

@Deutscheautoparts 9 лет назад

***** Sounds like its probably the strut bushings but its tough to be sure. You can try to lubricate the bushing to see if that helps. deutscheautoparts.com/5q0-412-331-d.html

@RCFunTime 3 года назад

Do you need re-alignment?

@MrCRios 7 лет назад

Is this the same on all cars

@thaDamester101 9 лет назад

7:05 Is there a tool that can be used to remove that clip on that screw there right above the wiring far left of the screen??

@Deutscheautoparts 9 лет назад

All you should need is a screw driver or your fingers.

@joshlowe670 7 лет назад

been looking between these and the h&r springs. wondering which will work better for a dcc car.

@erikwahr8454 4 года назад

check out Emmanuel design I have heard good things about them

@ElmoMac3000 9 лет назад

I have recently lowered my car using H&R springs. All was fine, but about a week or two later I now have a creaking noise when turning out of a parking space at slow speed. Any ideas? Would it be the upper strut mounts need replacing?

@Deutscheautoparts 9 лет назад

ElmoMac3000 You should likely consider replacing your strut bushings and bearings deutscheautoparts.com/make-model-year/volkswagen/gti/mk7-2015-present/steering-and-suspension/bushings.html

@xstretchthatmothax 8 лет назад

Is the installing for a golf the same? Looking at the golf, I didnt see the bolts holding the axel in, are they tucked behind the cb boot? Havent

@Deutscheautoparts 8 лет назад

+Justin Saxton Im sorry we are not sure

@Rtiffany0466 8 лет назад

Hey guys, love your videos. At what mileage would you recommend replacing the strut mount and/or bearing? Thanks and keep up the good work!

@Deutscheautoparts 8 лет назад

+Ryan Tiffany If or when they start making noise or whenever you have the suspension apart. We would say anything over 10k miles you should consider replacing them.

@Rtiffany0466 8 лет назад

+Deutsche Auto Parts Awesome. Thanks for the quick reply!

@slow8r 8 лет назад

Have you guys done a Golf R yet? I assume the front should be the same but are there any extra steps I need to do with the rear because I have the rear axle?

@Deutscheautoparts 8 лет назад

+Bradd Kordenbrock We have not but it should be pretty similar. Be sure to take a look at this video before you install the springs. People often break this. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-RZRcxIWg-7U.html

@bluepanther99 2 года назад

How did you manage to measure the torque when putting the bolts back? I don't have torque wrench and if putting as much man power as possible is enough?

@Joe_Jenkins404 2 года назад

I’d say if your going to tackle a job like this in your driveway you should at least have a torque wrench

@Smoovindecat 7 лет назад

Please could you do a video on the creaking suspension issues on the mk7 golf ??? 🙏🏼

@MR-lq4zv 4 года назад

Yesssss lot of click clacks / Ricketie ride at 10 to 50 MPH it's a sport Sunday special aggressive driving ride . It's not for the Daily driver YOU WILL GIVE UP COMFORT to NOISE CLICK CLACKS this is an inherant known trade off .

@Deutscheautoparts 3 года назад

- We appreciate your Support and Purchases! VWR (Racingline) Sport Springs for MK7 GTI: www.shopdap.com/mk7-gti-vwr-sport-lowering-springs-1.html Neuspeed Sport Springs for MK7 GTI: www.shopdap.com/55-70-07.html APR Sport Springs for MK7 GTI: www.shopdap.com/apr-roll-control-lowering-springs.html H&R Sport Springs for MK7 GTI: www.shopdap.com/h-r-2015-2017-volkswagen-golf-vii-gti-ow-sport-spring-5478755.html Complete Suspension Install Kit for MK7 www.shopdap.com/complete-suspension-install-kit-for-mk7-5g0498331bgrp.html Ultimate Suspension Install Kit for MK7/MK8 (non DCC) www.shopdap.com/ultimate-suspension-install-kit-for-mk7-non-dcc-5g0498331dgrp.html Ultimate Suspension Install Kit for MK7/MK8 (DCC) www.shopdap.com/ultimate-suspension-install-kit-for-mk7-dcc.html Volkswagen Magnetic Bolt Tray: www.shopdap.com/vw-magnetic-bolt-tray.html Optional Replacement Parts (recommended for vehicles with higher mileage) Replacement OEM Strut Mount www.shopdap.com/5q0-412-331-e-vw-audi.html Replacement Aftermarket Strut Mount www.shopdap.com/strut-mounts.html Replacement OEM Strut Bearing www.shopdap.com/5q0-412-249-e.html Replacement OEM Front Bump Stops www.shopdap.com/1k0-412-303-f.html Replacement OEM Front Dust Boot www.shopdap.com/5q0-413-175-c.html Replacement OEM Front Spring Isolator www.shopdap.com/5qm412545-vw-audi.html Replacement OEM Rear Upper Spring Isolator www.shopdap.com/5q0-512-149-f-vw-audi.html Replacement OEM Rear Lower Spring Isolator www.shopdap.com/5q0-512-297-d.html

@bwheeler111775 9 лет назад

Could you tell me more about the inner axle bolts? I am going to have a shop install the springs, but I don't want them to cut corners. So, I would like to get new bolts beforehand. Do you sell them or can you give me a part number? Thanks for the video!

@Deutscheautoparts 9 лет назад

Here are the inner axle bolts www.deutscheautoparts.com/View/N-909-911-02/N-105-234-01/0/15362 There are a total of 12 (6 per side)

@chavvyboy69 6 лет назад

I'm considering fitting these on my mk6 gti, would you recommend replacing the top mounts and bearings at the same time? Many thanks!

@dumbeezy5480 6 лет назад

Charlie Miskelly might as well

@coolvans1988 8 лет назад

No new camber arms needed for front or rear? I come from a 370z and that required changing those after dropping the vehicle with only changing the springs.

@Deutscheautoparts 8 лет назад

+coolvans1988 Nope the camber would not be terribly changed with a very mild drop like the VWR springs.

@Hubscharber 8 лет назад

What mileage should you replace the strut mounts and bearings? Do you need to replace the hardware as well? (bolts, nuts, etc.) I'm at 19,200 on mine and I'm looking at installing the VWR springs.

@Deutscheautoparts 8 лет назад

+Hubscharber I would say anything over 10-15k most due to the amount of work to get them back out. You can always roll without replacing them but the potential for noise from the old tops is there. As far as bolts take a look here we have the kits. deutscheautoparts.com/make-model-year/volkswagen/gti/mk7-2015-present/steering-and-suspension/install-kits.html

@paulwiest8167 8 лет назад

Hey guys, I was wondering how much psi are you approx using to loosen the upper strut mount? Received your springs last night!

@Deutscheautoparts 8 лет назад

+Paul Wiest most shop air is around 90psi. Thanks for the order, we appreciate it very much. You support allows us to make videos just like this.

@audiwankenobi361 4 года назад

One more thing: my 2016 Golf Sportwagen didn't have the type of axles that bolt to the transmission....i had to remove the hub bolt instead but i didn't have to remove the tie rod.

@Wamuwi382 2 года назад

I replace my OEM springs with Eibach Pro Kit on my Jetta 6,but there's a funny noisy when I turn left or right the steering wheel what can be wrong

@mihaistefanescu1999 9 месяцев назад

Even when you aren't moving?if yes,check the strut top bushing

@jeisonfernandez2414 9 лет назад

After installing the springs and getting an alignment how much negative camber did the wheels have?

@Deutscheautoparts 9 лет назад

We did not get an alignment after installing these as we were removing these springs to put coilovers on.

@libaichen8794 7 лет назад

Hello. If I use VWR springs do I need to change sway bar end links too?

@dopiaza2006 5 лет назад

So is there actually any difference in the suspension between a 2003 Mk5 and a 2019 mk7?

@aaronfrey 4 года назад

yes. not a lot, process wise, but they components aren't interchangable. the rear is very different.

@TheCraveFeeds 2 года назад

BE CAREFUL GUYS: The bottom three nuts on the ball joint is NOT 100nm, this is ~74 ft pound and this WILL strip and break the bolt on the ball joint(I broke 2 now) It should be 44ft pound.

@jmccann6735 7 месяцев назад

Correction: 44 nm equals to 30 ft-lbs, so even less than that. I'm getting my specs directly from the 300+ page VW technical service manual they distribute to dealerships. It also says the strut pinch bolt is torqued an additional 180º, not 90º.

@mercurialman23 9 лет назад

Would I need all these tools for a vw gti mkv 08 like are all the bolts all the same as my car to this car?

@Deutscheautoparts 9 лет назад

Yes this would be very similar to an install on a MK5. This kit should make up what you need for special tools, other than the spring compressor www.deutscheautoparts.com/View/1K0-498-101/0/533728

@KyleAndersonSkates 7 лет назад

This is probably a really silly question, but would putting these on my car void the warranty? Obviously if my shocks go bad I'm not going to go claim those on warranty, but they shouldn't mess with the engine warranty right? Also, for the 6 triple square bolts, any issues doing this method as long as the bolts are properly torqued? Lastly, my car only has 3000 miles, purchased on Oct 31st 2016, Would it be okay to reuse the knuckle bolt? Thanks Paul!

@JackTheTool 7 лет назад

i have been told before that modifications can void warranty if they are related to you problem.

@GabrielLimau 9 лет назад

Please i want a tuto to change commom daytime running lamp to led in Golf MKVII with headlights without xenon. Sorry for bad english

@Deutscheautoparts 9 лет назад

We will be going a Xenon retrofit in the near future.

@cdawg2413 9 лет назад

How is the alignment possibility of a MK7 Golf after lowering in regards to tire wear? I have owned cars that can be lowered 2" without alignment and does not affect tire wear (97 Pontiac Sunfire) as well as cars that had some major difficulty with just a 1.2" drop ( 05 Volvo V50) that would eat the inner side like crazy. Ideally I would love to drop my MK7 Golf, but do not want to lower the tire life from 4 yrs to a few months for just an inch drop like I had in the Volvo. Please honestly tell me, can MK7 Golfs be properly aligned with moderate lowering (1-2") . I don't mind a shortened tire life of say 1-50% but the 75% plus really cut into the wallet.

@Deutscheautoparts 9 лет назад

This should not affect tire wear in an outrageous manner. You will want to be sure that the vehicle is properly aligned after the install

@tomepp7760 9 лет назад

How come you didn't loosen the bolts holding the a-arm to the chassis? The problem is, those bolts are torqued with bushings inside and with the car set to an existing ride height (stock springs) at the time the vehicle was made. When you drop the car down with the new springs, you will in essence be over torquing the bushings in the a-arm assembly which will lead to premature failure of the bushing. I learned this the hardway lowering my 03' GLI and for the most part it's overlooked on these sorts of diy's.

@jasonvoorhees3666 8 лет назад

What exactly do you mean by "loosen" them? Are you saying they need to be loosened during the install and torqued back to spec after the install or that they need to be torqued to a lower spec after the install? Thanks

@tomepp7760 8 лет назад

+Chili Dog correct, they need to be loosened during install and retorqued back to spec with the car under load. Ie at the resting ride height. You can do this by putting a separate jack under the control arm and lifting it up to the correct height.

@jasonvoorhees3666 8 лет назад

Tom Epp Thanks a lot, man!

@jasonvoorhees3666 8 лет назад

Tom Epp Where exactly are these bolts located and how many of them are there? Thanks again

@tomepp7760 8 лет назад

eugh..it's been a year since I did it, but you can figure it out by watching where the a-arms articulate through. This time I actually took my car back to the dealership after installing the springs, the alignment was way out and the torques were all wrong since I couldn't get the torque specs. This is a small detail but super important, those bushing will torque out and you'll end up with all kinds of slop in the suspension after a while.

@csta92 6 лет назад

Lowering springs can afect the performance of the dcc shocks and damaged it? nice video

@hansdynasty 8 лет назад

How difficult is it to reattach the inner axle? I've been eyeing your DIY and been snooping around on the MK7 international page for a while, and finally pulled the trigger on some VWRs for black friday. About to order the Strut Knuckle spreader tool from you guys as well.. that's the only part of this install that scares me a bit. As always, keep up the good work Paul!

@Deutscheautoparts 8 лет назад

+Hans Son Thank you so much for the Spring purchase we appreciate it very much. Your support allows us to continue to make videos just like this one. As for this inner axle you might want to check out the coil over install video. Its a little more complete as we had some technical difficult while shooting this video. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-4vaZyJlrf2A.html

@ALE5six1 5 лет назад

Any differences when working on a car with DCC?

@villebergh9454 3 года назад

Little late, weird aswell. Did you gett an anwser on this? Im really curious myself.

@markbla3645 3 года назад

Just put H&R springs on my DCC car. There are ride height sensors you will need to unbolt and the connector that plugs into the struts. Other than that it’s the same.

@ALE5six1 3 года назад

@@markbla3645 awesome good to know! We're you able to reconnect those two sensors?

@villebergh9454 3 года назад

@@markbla3645 Thanks for the respont! Really great help. Ty so much!!

@kouroshgolban 8 лет назад

how long would it take a VW/Audi shop to install the springs. Or how much should I be paying. They wanted to charge me $550-600.

@Deutscheautoparts 8 лет назад

+Kourosh Golban Roughly 4-5 hours labor plus alignment.

@danydany5088 9 лет назад

where can I buy VWR spring for my GTI MK7?

@Deutscheautoparts 9 лет назад

Right here www.deutscheautoparts.com/View/VWR31G7GT/0/531815

@gavinschunick8857 4 года назад

Why does no one show the install on the harder side (Passenger side)? Every single video only show the drive side. The backs are easy as ever and the two rears take literally 30 mins. But the passenger side I’ve been working on for a few days as still it’s so close . But the strut won’t go ALL the way down into the Pinch bolt assembly. Not sure what to do ? HELP!