Mustang KEE Auto Top Convertible Top With Plastic Window One-Piece Vinyl 1994-2004 Installation

Подписаться 246 тыс.

Просмотров 523 тыс.

50% 1

🛠️ Download our free guide: The tools you need to work on your Mustang! bit.ly/465MGQT
Bill shows you how to install a KEE Auto Top One-Piece Vinyl Convertible Top with a Plastic Window on your 1994-2004 Mustang.
Purchase Product Here:
www.cjponyparts.com/kee-auto-...
Absolutely American made, this KEE Auto Top Convertible Top is for the 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 or 2004 Mustang. Owning a Mustang convertible can be great, especially on nice summer days. But one of the downsides is replacing the convertible top every 10-15 years. This was an install that was just a little too much for the average Mustang enthusiast. KEE understood this and released a one-piece convertible top that is much easier to install, and today, we're going to show you how to do it.
Check out more Focus RS Engine parts from CJ's here:
www.cjponyparts.com/focus-rs-e...
Check out more KEE parts from CJ's here:
www.cjponyparts.com/kee-auto-t...
Subscribe to CJ Pony Parts on RU-vid here:
ru-vid.com_c...

Авто/Мото

Опубликовано:

2 апр 2015

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 399

@blouderback 2 года назад

GREAT video! My wife and I could not have replaced the top on our 2001 Mustang without it. The one page instructions that came with the top are rather brief, and we would have been lost if we used only that. A couple of tips we found: 1. It's OK to cut away the old top to gain access to the nuts in the back. No reason to fold yourself into the back seat and fight the top you're going to throw away anyway. 2. Remove the 3 piece trim before removing the top, even though Bill says you don't need to. You have to remove it later in the install, so just do it during the removal. 3. lightly sand and paint the 3 piece metal body trim with a flat black paint after removal. It'll really look good next to the new top. 4. If you accidentally detach the OTHER end of the wire/spring that attaches to the brass grommet on the new top, you can remove the fake side triangular air intake body molding to gain access to where the other end clips into the body. 5. Take pictures as you remove trim, screws, weather stripping, put the screws/bolts into separate paper cups and label them. 6. Definitely use a power stapler. 7. Don't use spray adhesive, use some brush on contact adhesive. 8. Using a stubby torx ratchet is a must.

@dbrown4168 Год назад

Thank you

@kevinsmith4584 Год назад

Thanks for the tips. Especially the one about the glue - I saw the spray adhesive in the items needed at the beginning but only saw him use glue applied with a brush.

@arminteriors8590 8 лет назад

I guess you know by now, but for those who don't, you don't have to remove the interior quarter panels to remove the exterior trim. If you use a regular phillips screwdriver it will hold the beltline weatherstrip out of the way while you unscrew those two screws. Thanks for making the video. Really liked it.

@cjkeating1454 3 года назад

Did my first one today on my 95 Gt. This video is the best walk through. It is very tedious work but when it’s all done it’s well worth it. Took me 8 hours by myself. Thank you so much for making this video.

@poopytown9307 2 года назад

Ok his video is a hot turd n didn’t help at all

@bamcameback 2 года назад

@@poopytown9307 angles were pretty bad lol but should be enough to get the idea

@dbrown4168 Год назад

@@bamcameback and redundant info and he didn't go through and tell what mistakes he made bc he definitely made some things harder. I just wish he went through and added suggestions after like the fact that the inside near where the arms fold up has a deadly pit that you're going to lose all of your screws and bolts into if you're not careful And some of the tools list is wrong and not used and some not listed so that's unhelpful as well

@SEDONA525 9 лет назад

I installed an EZ ON Auto Top last night on a 2001 Mustang. I used this video and I'm very thankful to you for making it.

@Zerogivengarage 9 лет назад

We shot this over two days and probably worked on it for 7-8 hours total. Like I said I never installed one before so there were a few times I had to stand back and figure out the next step.

@malik16th 7 лет назад

Bill Tumas how do you bolt the liner back up to the bow?

@kenyabrown1463 7 лет назад

Bill Tumas will the plastic window fade with time do to exposure to the sun?

@Zerogivengarage 7 лет назад

Over several years if left in direct sun it will cloud up.

@kenyabrown1463 7 лет назад

Bill Tumas What care or protection products do you recommend?

@Zerogivengarage 7 лет назад

I always use products from Raggtopp

@shacoclone3299 4 года назад

Thanks for the video! Replaced the top on a 97 using this video and it turned out flawless! I was worried the aftermarket top would leave me with wrinkles, indents, or more problems. But after installing it and tightening everything down, it was smooth and looked good as new! Also, the large window has a much wider view than the original glass panel, minimizing the large blind-spots with the top up. Overall, great product and very helpful video showing how to install it.

@cphifer1029 6 лет назад

Never installed a top before and this video helped me to do my top perfectly, it took about 8 hours but it sure saved me a ton of money from doing it myself

@206guy7 3 года назад

Man, so far it's taken me a day of on and off work to get done what you got done in 11 minutes lol.

@kellybelew3340 5 лет назад

Oh yeah, When it came to the loopholes in the side with the spring loaded wire… Are used a coat hanger to loop through it before I tried to undo it so I didn’t lose it. It was very helpful because when I went to reattach the new top it also gave me something to hang onto while I Worked at putting the loop through the hole in the new top! Just a little helpful hint for anyone if it works

@jenniferbarnard4236 3 года назад

Thanks for this comment. I missed this step on the video in the removal process and we were confused. 👍🏼

@charliebriley7591 8 лет назад

Good video Bill and good top Kee ,ordered the top got it in 2 days, Took me 2hrs to remove the old leaky top and about 5 hrs to install it , I watched ur video a few times, very helpful ,the only rough spot I had was hooking that loop wire into the eye hole at the bottom of the rear side glass that was a booger, But I saved a lot of money doing it myself, Thanks CJ Pony Parts.

@kennyturner1228 4 года назад

Just finished my 2003 GT. Holy Hell!! That's a job I hope I never have to do again as long as I live! 12 hours to complete. But remove the bolts in the rear well FIRST! Don't wait until the point he did in the video. It'll just be easier on you.

@bengordon7635 3 года назад

I cut my top off before removing rear bolts ......... mine were all rusted plastic coming off bolts , 1 bolt broken off yes his video is on a like new mustang in reality most these cars with leaking tops for years are all rusted up and had too replace all tension cables they were rusted also .. I replace headliner with a insulated one much better and well liner also my car smells new again !!!!!! cheers all !!!!!!!!!!!!!!!!!!!!

@stevenfowler9120 7 лет назад

Excellent job on this video I purchased my keep one piece and spent my Sunday putting it on. I made a trip to harbor freight to pick up the listed tools I didn't already have. Finished mine in 9 hours and it came out perfectly wish I could post a picture here. Well worth the money. Keep up the good work CJ Pony parts and Kee top!!!

@datnigga529 6 лет назад

Literally just got done with my top this video is such a help thanks so much. I truly appreciate the time you took to make it. Im not even a mechanic at all either

@biggytupac 8 лет назад

Just finished, came out great. I had the luxury of a garage and time. Replaced tension springs as well and tack strips(all dried and cracked). Removed headliner as well , it was filthy. Thanks so much for posting!

@frankiebridges6279 4 года назад

Thanks Bill after watching your video twice,knowing I'll watch it again before I attempt putting the top on my 96 Mustang GT.Got a friend gonna help me,he's watching it too so we'll be on the same track doing this job.Watched your video on redoing the seats ordered the kits for my 1965 mustang. They turned out beautiful so thankful you took the time and video these things for people like my self.Thank you so much,

@cjponyparts 4 года назад

Glad to help! Good luck with your install!

@marcusspicer2676 7 лет назад

This video was a great help for me. I installed my one piece top 8-5-2017 myself. It took about 12 hours to install on my 03 Mustang. Thanks Bill!

@monetmalisham5341 3 года назад

What staple gun u used and staple

@andreww8881 8 лет назад

Awesome video, saved me $1000 roughly. Took about 8-10 hours but really worth it. If you have a 94, the 16 nuts at the back well take a 13mm deep well 12point socket.

@biggytupac 8 лет назад

That's exactly what i used. Great tip

@edwardprete 7 лет назад

Andrew W nice tip!

@rjunker 6 лет назад

Thanks Andrew W! This was definitely not a 9/16". Thanks for saving me a 2nd trip to the store.

@thatoneauthor 5 лет назад

Omg!!! This is what I was looking for. Hopefully it helps bc I'm losing my mind on them 😫😫

@206guy7 3 года назад

My gf's is a 98 and it was a 13 deep as well.

@jimieb01 8 лет назад

Did mine on the weekend, turned out great! Took me 8.5 hours . Not a job to be rushed. Recommend extra torn bits just in case you snap one. Highly recommend this roof !

@ScorpXM 8 лет назад

Did your's came with glass window? Mine has glass window i wonder if it will take longer. This weekend will try to install.

@CRUSHFACTORPC 7 лет назад

I believe your window will take longer to install I installed this one piece top Took me about 12 Hours as we did not have EVERY specific tool listed and well takes longer.. It looks fantastic BUT 1st try and find a video for your specific top IF possible I see your post was two months ago LOL sooo I hope it all went well...

@geraldriddle7984 7 лет назад

ScorpXM loop M mO

@kellybelew3340 5 лет назад

This was an exceptional Video! I have never had a convertible and I bought one used last week. I watch this video about three times, ordered a new top, and just finished with exceptional results! The video made me believe I could do it…! The best part is I did it and I am a girl! Thanks for your time and for posting the video! Your recommendations For where to get the top it fit perfect! And I would advise anyone that does this to watch the video and not think ahead. I tried to think ahead and it took more time than I wanted but again, excellent results! Here’s to you!

@ghostqueen798 2 года назад

My daughter and I need to do it.. this gave me more courage!! Thank u! She has a convertible for her birthday 💜

@bread50321 8 лет назад

If someone else is watching this on their phone and you can hear it, it sounds like Jimmy Kimmel is teaching you how to repair your convertible top.

@nsdnny 9 лет назад

i just did a two piece top on my 1997 mustang gt. this video was a life saver. it was my first time doing the roof. yes a two piece is a little different it basically is the same just more time consuming putting the rear part of the roof on. it staples in the same spots as this roof just you have to do it for the window then the roof. most new roofs come pre-marked and pre-cut. and now like the KEE one piece has the sleeves for the bow to make it easier to so you don't have to stretch each section then staple it down to the bow. If you are going to attempt to put a roof on your car. I do recommend the two piece roof as it is the original style and what the car was designed to have. However the one piece roof is just as good and if you prefer that style thats fine. the two piece roof takes just as long as the one piece with them being so much alike to put on which with no experience putting a roof on took me 5 hours over the course of 2 days in 105 degree heat. this video really does tell you basically how to put on both styles of roofs for this car. if you have any questions about the two piece roof id be glad to answer them. but the video pretty much tells you everything that you need to know for putting both roofs on other then the two piece roof you have to put the back window on starting at the top then staple it to the bottom tack strips that you bolt to your trunk and be sure to measure the distance of the top bow to the tack strip before you remove old roof so you put the new one on tight enough.

@abymondesir23 6 лет назад

Incredible video and saved me over 400 bucks just finished mine on my 96 gt thanks cj pony. Roll bar next

@Presidentgraham 4 года назад

For never installing one before, pretty good job. one of our biggest issues was putting in the bows. The top has NO premade holes. If you have a second set of bows that will help you alot! We are still working on this job, working slow and trying to not get too angry.

@jackwolff9534 3 года назад

We likewise found the Bows to be very frustrating since there are no holes in the sleeves in the top. All in all it took us 22 hours to install the new Top. The bows were the most frustrating all of the tension cables at the bottom on each side were also a challenge. The video skips what to do with the tension cables so we just cut the old top since it was coming out and left the tension cables attached at the front. I would strongly recommend other first time installers buy some extra parts because we had parts that failed as we did our installation. For example the rear tack strips those three aluminum plates, two of the plastic covered nuts crushed those in two spots without ever tightening, and one of the plastic covered nuts split and came off the nut before it tightened as well. Also be wary of dropping tools and parts into the frame/fender well at the rear window. Any items dropped in there are very difficult to retrieve.

@cmscms123456 5 лет назад

Great video as usual. One hint. leave the top lay out in the sun for a couple hours, maybe over another car roof, as you are disassembling the old top. This loosens the new top, and flattens out the folds and waves from being in a box for months.

@cjponyparts 5 лет назад

Thanks for the tip, this was my first time ever installing one so I am just happy it worked lol

@darrylvance5874 8 лет назад

Really a great video ! I followed step by step and installed my new KEE top with no issues .. Thanks !!!!

@sha-bobawatermonkey2398 3 года назад

Did you have any trouble puttin up the headliner

@clydepodvin5026 Год назад

Best video I've seen on replacing the convertible top. I have a 2003 mustang that needs the top replaced. Thanks for sharing this with us 😊

@kelvinstrickland7442 3 года назад

I am putting a new top on my 1999 mustang convertible And This Video Will Serve Me Well. Thank You From Niagara Falls Ontario Canada.

@PhoenixZong 7 лет назад

took me 18hours solo including breaks and eating

@rabbitmartinez4456 7 лет назад

PhoenixBHO how long were your breaks lol😂

@rabbitmartinez4456 7 лет назад

PhoenixBHO did u get frustrated ??. I'm thinking of doing this project on my 06 mustang

@kiellivingston7100 5 лет назад

Took me 10 days including getting sick in the middle :(

@DanielSloanMusic 5 лет назад

So we went with the plastic because our glass shattered in the NC heat sitting in workplace parking lot. I like the look and ours had also began separating from the glass. This makes an every 5 to 10 year replacement pretty simple.

@aceautoglass44053 7 лет назад

y'all can hate on Bill all you want to but that was a great job first time that's a lot of work and it looked great to me you the man Bill thanks for posting the video and all them staples was just to hold in place till you get the plate back on did you not see the plate that went over the staples with 500 screws in it thanks again Bill

@jason91205 3 года назад

Holy moly! Never knew how much work was involved in this. Now I know why people don’t want the verts haha

@donny042 8 лет назад

Great Video.. My Sons New Top Came Today "2001" After Watching This Video Can't Wait To Get Started In The Morning Thanks For Sharing It!! With All The Hidden Screws Great Job !!

@arturoahedo7067 6 лет назад

First of all, i am not a handy man at ALL, but my son and I followed your vid and after some good hours and couple stress moments we did replace it. Once we finished, it wouldn't lock all the way but i left it some hours under the sun and helped stretched the roof down. Got a lil tiny leak somewhere in the back inside,but i will disassemble the back retainer and check the cause. Other than that you helped us saving at least $350 labor. Thanks again man and thanks CJ Pony Parts.

@labandanp 8 лет назад

I just done mine. Perfect tutorial. Although in the front of the top, where the liner and the top unite it's tricky because the plastic that it was there was broken, so i glued back together. (top screws were so rusty, they wouldn't even come out). But I wish i could upload a picture of mine.

@john-t-bjohnb3588 3 года назад

Thank you for this video. Just finished putting one on my sons 03. Came out nice. I learned a lot.....like I'll never do another one haha!!!! There were instructions with it so this video was the instruction manual.

@sha-bobawatermonkey2398 3 года назад

I have a question sir

@onlysolutions6612 Год назад

Just bought 2001 , top has to be replaced, was gonna pay someone else , but after seeing your video, am confident ill be able to do the job my self and save few hundie , Thx for your videos, very informative and to the point

@joshtaylor2093 7 лет назад

I have a plastic rear window on my mustang I think it looks fine, also thanks for this video I have made a lot of money putting on convertable tops for other people

@ramansandurya6971 6 лет назад

Where abt r u im in Vancouver

@davidwiley8547 6 лет назад

Thanks so much for the video jus did our top cake out great

@CRUSHFACTORPC 7 лет назад

NOTE if you have a Mustang GT the roll bar will need to be negotiated when removing the rear interior quarter panels Outside of that... This video is very detailed .. I would recommend actually taking pics of your removal steps as well to be able to reference how things go back as the video isn't perfect BUT its pretty spot on. Use every tool they list we didn't and it cost us some aggravation and time and pre plan exactly where you will store the massive number of screws such as little envelopes with a description of where they came from and place them out of the way .. AVOID doing this around young kids .. they love to watch and well be kids... Not toddlers BUT the 8 - 15 year old crowd LOL ... we did manage and top looks great.

@babymikey6732 2 года назад

thanks for the tip. i just made up a bunch of envelopes. waiting for a clear day to do mine.

@angelov5709 2 года назад

Bill thanks to you and your company I did my first top for a needy family who was running out of duct tape. I did it for free and showed them the video and the rewind video that was refreshing and spurred me on. Thanks again Angelo

@brettholt6277 4 года назад

About finished with mine. Took a damn day to get the damn thing off. Been working on it a few hours hear and there at night time, my apartment complex don’t want us fixing cars... Those plastic bolts are 14 millimeter splined socket... Broke one of the plastic nuts, took it to Home Depot, it’s a M6.1 replacer that with a wingnut and a washer... They should make a bolt on replacement for the whole top headliner shit would save hours and frustration. But like anybody else I’m not going to pay some dude a $1000.00 to put on a $195.00 part.

@rosscoyer7611 3 года назад

That stapler needs a little more oomph. I'm about halfway through this job, loving every minute, thanks CJ Pony!

@rosscoyer7611 3 года назад

Update, I finished the job this morning, but am having trouble closing the top. It's coming up short/tight about an inch. I glued and stapled the front of the top the length that was recommended in the video. I am wondering if anyone else has had a similar issue and if the top will stretch? Side note, I am in Northern MN and it is currently 20 degrees outside. Unheated garage. Obviously this probably has something to do with it, but just wondering if I will have to shorten the connection in the front to make up the difference or if the top does stretch when it warms up? Otherwise, the job went well. A few takeaways for anyone thinking about trying this. It is a VERY tedious job. Lots of tight spaces, pieces, parts, places to lose screws and tools... You will need a variety of tools, wrenches, a big work space and extra hardware likely. The little ratchet he uses in the video, or something similar, is imperative. Also make sure to order a set of clips and a clip tool if you don't have one. You will need it as well. One recommendation I would make, if you could center the top properly I would have attached the middle bow first. Getting the small screws started that hold the headliner on after the window flap is stapled on is a BEAR. I could be overlooking something, but it would have been much easy to attach that bow had the window flap not been stapled on the rear bow yet. The clip spring tensioners are a challenge as well. I found that once I got the clip undone with a set of very long shafted needle nose pliers and a slotted screw driver, I bent the clip wide open which made it long enough to reach through the hole in the new top. I then bent it back into shape which tightened it up nicely. I stripped several of the nuts that hold the tack strip on and had to use vice grips to tighten them. Shame on them for using a plastic housing. I used 3/8" staples on the rear bow, and 1/4" staples on the front. As I read in an earlier comment. It is easier to take out the back seat and inside quarter panels right off the bat. Thank you to the guy who recommended that. Anyway, by myself, it was about a 12 hour job. Very fun, the car looks great. Thanks again Bill and CJ Pony Parts! -Ross

@TheHandsOnGang561 6 лет назад

You did a awesome job, finish result looked real nice. Think I’m missing some weather strip or something cause theirs a gap right in the back corner by the small back side windows. Also wish you guys had a headliner installation video 😏

@Lealtad87 6 лет назад

Very good detailed explained video... I had a guy install it on my car and was not very satisfied with the results... With this video I managed to fix the faults.. thanks!!

@martincabanillas7484 7 лет назад

best video ever!!! THANKS BRO.

@cc9z 8 лет назад

wish you could work on my mustang hereI enjoy they video's you make very helpful when I work on my fox

@playboyh415 7 лет назад

Bill you are the best man👍🏼

@Zerogivengarage 7 лет назад

I try

@taylorrichter1320 2 года назад

Just used this video yesterday on my 01 vert looks so much better with the black top

@hectorterrazas8415 6 лет назад

Great video !

@redlinemustangs7963 8 лет назад

I just want to say thank you for putting this video up I have been looking for sum one to show how to do tops and never found one so again thanks but after seeing its complexity Im just going to get a professional to install it cause Damn its going to eat up my Saturday lol !

@Zerogivengarage 8 лет назад

+Redline Mustangs Our videos always seems to do one of two things. They either show you how, or convince you to pay someone else lol

@angiepena4681 8 лет назад

+Bill Tumas great video it was a big help got my New Top on Wednesday and my Husband is putting in on Right Now big help thanks to ur Video Great Job

@markusmcschallenburger4151 Год назад

I replaced my top 2 years ago and this video was invaluable!! My top and headliner got slashed by some punk about a month ago so I am putting the same top on. I love this video but wish there was a similar video to replace the headliner.

@prauwnsauce Год назад

In those two years before the incident did it hold up, also did you use any kinda convertible top sealer or conditioner or anything on it after you installed it?

@benjaminsevilla9794 4 месяца назад

i’ve never replaced a convertible top,i had one of my friends help me out and we knocked it out in 4 hours.Definitely tedious but the one piece top made it much easier i’m sure.

@mykobrafp79 8 лет назад

awesome job, wish me luck with my 94 mustang lol.

@tomwilderbuer8337 5 лет назад

Fabian Pulido hey I'm installing a new one on my 94. Did you have an issue with the 16 bolts around the well liner? (9:11) The 9/16 socket fits but they are plastic, and in so tight that I'm just rounding them off.

@Enoughinfo7026 3 года назад

I appreciate all the step by step help you have give, if you more videos concerning convertible tops free to send me a few. I have a 1970 convertible Pontiac Catalina. Would love to hear any insight into helping me with my project, yours truly PC Man

@johnk3734 4 года назад

bills like oh thats how that works lol. good video thanks alot

@johnnyblair9237 8 лет назад

thank you for a great video

@dorphotography6670 7 месяцев назад

Looks great!

@Elmo_Fuddleputt 3 месяца назад

I replaced my top about 10 years ago and something I learned. When you are removing the retention spring on the side, use a pair of VISEGRIP needle nose pliers because if you use regular needle nose they may slip off resulting in you punching yourself in the face, breaking your nose and having a whistling snot-locker for a month. Ask me how I learned that.

@BryanBlaz 6 лет назад

Man this saved me so much...replaced my top in 2 days...Thanks

@CHIVIRICO-GAME 5 лет назад

Increíble video man, lo vi un par de veces y me ahorre 1000$ dolares. Yo mismo instale el top a mi mustang GT.. Thx..

@cousinsautomotivedetailing1660 22 дня назад

This video really helped. Thank you.

@risky3923 4 года назад

If you have a 2000 mustang GT convertible there are 19 nuts in the back well

@lyingdogfacedponyboysoldie6479 3 года назад

This is tremendous work. Question. If you had needed to make adjustments to the top frame (due to improper closing) does removing this top facilitate those adjustments?

@connorbuss7884 2 года назад

did this by myself and it took me a little over 10 hours to do removal and install, keep in mind i’m an 18 year old kid with no experience with anything like this at all

@guyd37 9 лет назад

Thanks Bill but I will leave this to a pro...

@superwintebow1595 7 лет назад

thank you so much you helped me out a f****** lot just did my top and it looks perfect just like your top

@rabbitmartinez4456 7 лет назад

Super Wintebow hi , how long it took u? .. I think I'm going to do this project

@superwintebow1595 7 лет назад

rabbit Martinez 5 hours but it was worth it

@jfrankie80 6 лет назад

Where are located?

@BenFoilHat 3 года назад

How important is that cable behind the rear quarter panel? When I removed the convertible it wasn’t attached at the bottom and I’m wondering if I could just not worry about it or is it important to figure out how to re attach it at the base

@ayleslove4710 9 лет назад

awesome, thank you!

@arinder7 4 года назад

What size staples do I use to put the top back on with?

@b_man3179 4 года назад

Does the plastic back window develop a crease in it when being folded up ?

@luisaviles8359 6 месяцев назад

Excellent job 👏

@azulmillonario78 5 лет назад

Thanks I'll do it myself 👍✌️👏

@UnknownSlappaa 8 лет назад

can you please do one for the fox body mustangs?

@felipemiranda5873 5 лет назад

2019 and still the best video ive found thanks from brazil

@work101work9 4 года назад

@Build a Reef Aquatics he's the best. I mostly follow him on how to.

@marcostorrens6849 8 лет назад

great video

@Malo515 3 года назад

What can I use as a window defroster for my plastic back window?

@bobeech9728 8 лет назад

Hey Bill! I've seen you carry the 03-04 Cobra convertible cloth top, and was wondering if could get and install that top on my 00 GT. and will I need a new rear window or can I re-use my heated window?

@BenFoilHat 3 года назад

What size are the plastic 12 star bolts that hold the tack strip in? 9/16 or 7/16? The tool list says 7 but you said 9. Also what kind of adhesive did you use for the front edge? What size staples did you use? Thanks, great video I appreciate it.

@Thumb_Coast_Aerial_fpv 3 года назад

It’s a good walk through, I Installed one of these before RU-vid, lol That staple job doesn’t look to strong though, lol did you have to hammer them in farther? Nice video .

@dominicbavaro3043 4 года назад

84 people watching this video own Camaros

@ajgriffin87 4 года назад

Dominic Bavaro 🤦🏽‍♂️😂

@Panchitoisdead714 4 года назад

*85 😅

@nim22rodshadetree72 3 года назад

Thanks for the video Bill, very helpful. It appears you did not staple the rear edge of the fabric top @ the trunk, to the long 3-piece rectangle shaped staple bar. You only used the nuts to squish the bar against the top material. Why is that? Was that staple bar only used (with staples) in conjunction with the 2-piece top with glass window? The only staples you used were at the rear crossbar ( I read other comments 3/8" Stainless Staples), and you stapled the very end at the front of the vehicle (1/4" Stainless staples). Others beware when removing old top to take time and remove each staple, as you can easily break that 1/4" thick plastic staple strip, which is only riveted every foot or so to the metal frame. I also noticed you did not use any glue for the fabric, under those vertical molding pieces that get screwed in, as it appeared when I removed my top, there was remnants of glue there. Do you suggest using glue at the trunk behind the fabric top? Or just squish it under the many nut/ bolt connections? Thanks again.

@georgelassier9337 2 года назад

i like the way they spin right off mine strip before they turn using a 9/16 racket

@dorphotography6670 7 месяцев назад

I'm gonna tackle one during the break!

@nappidevi4049 4 года назад

Is there a way to get the bolts inside the drunk off if you don't have a 9/16 socket? Or if the bolts are alil scratched up?

@korbenelements 8 лет назад

Help at 18:55 if you pause it. See that rubber seal that has the studs going threw it thats attached to the metal of the car. then the top goes on and then the tack metal strip. What is that rubber piece called and where can I get a new one?

@PhoenixZong 7 лет назад

doin my 98gt n there are surprisingly more differences than the new edge in vid.

@Indica_Clark 7 лет назад

Hey Bill, anyway to tint the plastic? Would standard window film stick?

@331SVTCobra 6 лет назад

13mm socket also works on well-liner nuts. You didn't really address removing the tension cable from the existing roof. I shot mine with lubricant and pulled it out. It was hard getting started, but then it came right out.

@justincarrillo9228 8 лет назад

27:54 thats what she said...

@MZHAMRICK1 8 лет назад

+Justin Carrillo i didnt even have to go back to it lol

@ricksfoodhacks 11 месяцев назад

Im about to take my 1999 Mustang cov. to get the top replaced! will this one your showing us should fit perfectly?? Thanks!

@adamn1371 4 года назад

do a video on replacing seats and interior

@Mrd9960 6 лет назад

Hey Bill, I have a plastic rear window on my Mustang, would it be safe, if I go through an automatic car wash you think?

@nijagaradavidson7834 7 лет назад

Tension cable got loose on passenger side :( How do I get it back on?

@robertconde4064 4 года назад

Unfortunately I need to replace the plastic trim where you staple the top to. Can’t seem to find it anywhere online or know the name.

@reneebouye8014 6 лет назад

Where can one buy the weatherstrip/gasket behind the rear tack rail? The old one is crumbly. I can't find it.

@romantorrano2355 10 месяцев назад

Excellent work thank you so.much

@cjponyparts 10 месяцев назад

Welcome!

@kckk7027 3 года назад

Very nice video, I have a 2003 mustang and I'm getting ready to do it....thank god for youtube, because they give you crappy instructions when you buy one....