Mustang Modified Flasher Install 

Thanks. Just got mine today, and wasn't sure how to get the old one off. Other tutorials say "remove the old one," but didn't say how to. Thanks to your post, I had this done in 5 minutes.

This video just saved me a huge headache and a lot of money. Such a simple replacement. THANK YOU SO MUCH!!!

Dude I wrestled that clip for 20 minutes until I found your video.. thank you.

Great video !! For those who are wondering if it will work with a 99-01 Cobra (Ambers) IT WILL ! I have a 01 Cobra when i put LED's in, it started to hyperflash it got annoying so i went to O'reillys and bought one for 15.99 & installed mine today and it brought it back to normal ! Dont pay 40 bucks for the raxium one at American Muscle, go to your local part store and get it for less than half that price its literally the same thing !

Thanks for the upload! I ordered the same kits from raxiom and was looking all over for that damn relay. It slowed the lightning fast speed of the blinker down, but its still pretty fast.

Install took less than 3 minutes thanks to your tutorial! I appreciate your help.

Thanks for this... that damn stock flasher is hard to get off until you know what direction to pull. lol

So take the stock yellow flasher and stick a small flathead screw driver on both sides and pry to get them between the yellow housing and black part. You can slide the flasher out of the yellow casing. Do the same on the raxiom flasher. The guts are on the board which has the prongs on it. Take the raxiom one and push it into the stock yellow housing and it will snap in. Make note that you have it installed the right way. So when you plug the flasher unit into the car, the clip secures the itself to yellow flasher just like how it was. Then you can slide it back on the metal tab under the dash and it will look factory. Only takes a minute to pry each flasher out of the housing. Super easy. Little chance of breakage.

For those with an SN95 model. Mine is a 97 the flasher is located behind the fuse box under the dash! Hope this helps!

Thanks for this, couldn't have done it with out it. Thezip tie and velcro were great ideas. Thaks

Thanks a lot man this was really simple to follow along with, hope you keep on making vids(:

You just helped me fix my broken blinkers, thanks brotha!

Thanks. Works on my 03 cobra

Funny that it's a better tutorial than the guys trying to sell these overpriced units. Thanks Bro

ITS SO KOOL TO WATCH YOU WORK ON UR BULLITT CUZ I HAVE THE SAME CAR BUT MINE IS BLACK THANKS FOR THE VIDEO

So you have the stock talights and the original wiring right? And once you installed Raxiom Modified Turn Signal Flasher V1 it will do that sequential?

You are very welcome

Thanks, I couldn't find the Flasher Unit. I still had trouble getting it out because my shoulders are too large.

What stock sequential flasher are you using? Are you just using another module to make it sequential or did you get a whole new tail light?

Thank for the video. I got my relay for 8 bucks on email.

They're $12.99 at autozone

thanks for the info and the how to video!

Thanks, found this helpful

all I wanted to know is how do I turn off my hazards on my 2010 Ford Mustang the switch do not work anymore to have it like I had to unplug the battery just to stop them hazard lights I cannot find nothing on his dog on RU-vid to tell me can anybody help me tell me where the fuse is or tell me what's going on with my problem

can someone explain to me where the hell this is located? i looked under my gas pedal and dont see anything. Trying to fix my turn signals

Is it impossible to mount it back in the stock position? I can't... for the life of me get mine back up there.

Is it located in same spot for newer mustangs ? 2011

Sexy mustang btw

Mine will not budge

I think you got ripped off.... American Muscle sells the exact one for $29.99

I NEEEEEED TO KNOW HOW HE TOOK THE CLIP OFF , important step and he skipped it