My $900 Predator 212cc Wont Run ~ Subscribers Engine Teardown

Подписаться 417 тыс.

Просмотров 406 тыс.

50% 1

Today we get in Jose's Predator 212cc that he built. He spent $900 on this build and when he was done it wouldn't run right. We go over the basic things you need to have a good running engine. Then we tear into it and find out some big signs that this engine build went bad.
Check Out Blaster Products - bit.ly/3e9KqO1
Parts Used On This Build -
Predator 212cc Hemi - bit.ly/2VBPOjW
Billet Flywheel - www.eccarburetors.com/arc-spe...
Billet Side Cover -
Billet Side Cover O Ring - amzn.to/46vyn7g
Billet Rod & Wisco Piston - amzn.to/47PX9A1
26LBS Valve Springs - amzn.to/3GhfNF7
Chromoly Pushrods -
1.2 Ratio Rockers -
Super X Cam -
Predator Carb Jet Kit - bit.ly/47uusca
MSD Coil Pack - bit.ly/3wn8uX2
Valve Cover Spacer - amzn.to/3GcPIHv
Stainless Valves -
Billet retainers -
Merch & Events - bit.ly/33YbmtO
Parts & Tools used on the channel - amazon.com/shop/redbeardsgarage
Quantum Machinery- Siegmund Welding Table - bit.ly/36PHm6G
- Nargesa CC60 Bender - bit.ly/2xWDVxj
Prime Weld Tig 225x - amzn.to/3L4U3MG
Prime Weld MIG180- amzn.to/3KVUPvn
Amsoil Affiliate - bit.ly/3TWtrmM
Benchmark Abrasives (cut-off wheels, flap discs..) bit.ly/2SENg4f save 10% REDBEARD10
Want to donate without the commitment? - paypal.me/redbeardsgarage
Want to send us something?
Red Beard's Garage
P.O. Box 572
Sweetwater, TN 37874
Facebook - redbeardsgarage
Instagram - redbeardsgarage
TikTok - redbeardsgarage0
Pinterest - redbeardsgarage
Twitter - redbeardsgarage
Instrumentals by Chuki Beats - / chukibeats
-------------------------------------------------------------------------------------------------------------
*********Disclaimer*********
Please do not try to re-enact or recreate anything you see in these videos. We are trained professionals. Red Beards Garage does not take any responsibility for injury's created by doing so.
#RBGKarts #RedBeardsGarage

Развлечения

Опубликовано:

26 ноя 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 530

@941GKFAMILY 5 месяцев назад

Yooo man Thank you so much Greg it’s truly a blessing for you to help me out man god bless 🙏 - Jose

@NubsWithGuns 5 месяцев назад

We need to see the machine that goes in when it's ready.

@941GKFAMILY 5 месяцев назад

For sure I’m working on a go kart frame it’s going on a Go Kart -Jose

@jerodTSI 5 месяцев назад

@@941GKFAMILY🙌

@NubsWithGuns 5 месяцев назад

@@941GKFAMILY Greg welds too so can you break that also so we can learn more? ROFL I am kidding, I wish you the besr of luck with it.

@941GKFAMILY 5 месяцев назад

@nubswithguns hmmm 🤔i just might… 😂 no I’m kidding red has helped me a lot already to me it’s more then enough

@mikesbarn1858 5 месяцев назад

Let he who is without oil throw the first rod. Lubricants 14:3.

@Savagegunner217 5 месяцев назад

No hate on Jose. Everyone starts somewhere, that's why we learn from our mistakes and don't give up on what you love to do

@941GKFAMILY 5 месяцев назад

Amen brother -Jose 🙏

@kwaaaa 5 месяцев назад

100%!! Learning and teaching is how this hobby keeps going. Never be ashamed to learn, but always be willing to teach.

@Savagegunner217 5 месяцев назад

10000000% in order to know things you need to learn if it means mistake are made

@chuckwalker4149 5 месяцев назад

When I watched this, I started remembering some of the mistakes I’ve made on cars and small engines over the years. A LOT of them.

@Savagegunner217 5 месяцев назад

@chuckwalker4149 same some were major some were minimal

@jhbrown53 5 месяцев назад

Greg you should do motors like this from time to time. We all could learn from mistakes and help with diagnostic . More power to Jose

@ianfairbanks1318 5 месяцев назад

LOVE THIS! "Fix a Fan" should be called this segment

@kirklarson116 5 месяцев назад

I loved this video!!! Not only are you teaching others but you're helping someone who has worked hard for something and can't find the answer. Thank you for doing this Red Beard.

@racerdude7149 2 месяца назад

Working hard would mean the person read at least SOMETHING about engine assembly. I think what you meant was helping others that spend hard after watching a RU-vid video

@Core-vu6mc 5 месяцев назад

Great video. Thanks to Jose for putting himself out there!

@941GKFAMILY 5 месяцев назад

Thanks to you to brother - Jose

@steventwiddy3402 4 месяца назад

Everyone makes mistakes and if they don’t it means there not doing anything, I work on multi million dollar aircraft and I can tell you mistakes are made all the time……….they just are a lot more costly when they do happen

@82lube 5 месяцев назад

Truely one of your BEST videos. Awesome to see the breakdown & your analysis of the engine & why it wasn't performing.

@charlesbroussard9289 5 месяцев назад

this is why i watch your videos helping this guy out and teaching others is all good

@gabecarmichael9072 5 месяцев назад

Awesome video, and kudos to you for donating the block and crank of the test bed. Hats off to you for taking the time to tear it down, explain, and making it right for the guy who sent it in.

@dirkdigler5332 5 месяцев назад

You are just an all around good guy Greg. Thinking of others and helping people out is where life is most rewarding.

@tinygaragepowersports0122 5 месяцев назад

Super cool of you to take on this guy's engine and investigate. Kudos for donating your own parts as well. God has blessed you, and now Jose's engine will be blessed with the ol' Red Beard touch!

@941GKFAMILY 5 месяцев назад

Amen to that sir 🙏

@petercasper224 5 месяцев назад

I have to say RB, OUTSTANDING channel! You guys are real mentors to the next generation of knuckle busting gear heads. This video should be shown to all the grease monkeys in school and I mean that in a very positive way. I can still remember when I was in shop class tearing down the old Briggs engines and the first time it fired up after putting it back together, very rewarding feeling. You have so much respect for this hobby. Over the top channel guys!

@kylewest100 5 месяцев назад

You should do this as a episode series. Get people’s projects that are new to engine building and having issues and go through it and show where they went wrong and how to address the issues. I think this is just as beneficial as showing how to build engines correctly. Reason I say that is we only see a guy having everything going right. Only time we see guys having issues is when something breaks.

@Threads1220 5 месяцев назад

You can definitely use a standard compression tester on these engines the compression release does not effect the results because most modern compression guages have a check valve and the engine still makes compression before the compression release releaves it I have checked compression before and after removing a compression release on my road to horse powers and it was the same useing a standard harbor freight compression guage

@bigbaby1177 5 месяцев назад

Good for you Jose for being open minded and ready for constructive criticism!

@941GKFAMILY 5 месяцев назад

Ofcourse my man there’s always room for new knowledge - Jose

@RedBeardsGarage 5 месяцев назад

I completely agree!

@towboatjeff 5 месяцев назад

This was a really great video. Nice to see the problems someone came across on a first build.

@elesjuan 5 месяцев назад

One con to the dingle berry ball hone is if the cylinder has uneven surfaces like pits from corrosion, the balls will follow those uneven surfaces. Generally I prefer to use the flat stone type as they’ve got a better chance of evening out the bore. Just my opinion from experience.

@bobc8694 5 месяцев назад

A ball hone is meant for deglazing the cylinder. It's not meant to use to get cross hatching back.. The correct way is to use a straight hone, like a Amco, Sunen,ect but a straight hone is what you want. Otherwise if your cylinder is out of round it will show where it's has low spots and when you are done you know it's perfect.. even after boring out a cylinder you always take the last few thousands out with a straight hone... NEVER A CHEAP BALL HONE... Those are about 35 to 70 dollars and a good straight hone is around 5 to 6 hundred dollars...not trying to be a smart ass but like you said after doing something wrong and then figure it out you learn... so hopefully you will do some research and you will find out what I have Said is correct.. you will never see a good machine shop ues a ball hone and then put it together. We use a ball hone first to clean the cylinder and deglazing a cylinder before assembly you use a straight hone to get proper clearance and a good cross hatch.... and if you do it your way or how I explained. And do a leak down test on the cylinder your way and it will have more blow by a lot sooner than if you used a straight hone.. this is a fact and thousands of engine builders will back it up... take care and have a great day....Bob....

@BurnoutSmoke1776 5 месяцев назад

This has been one of my favorite videos, super enjoyable. There are some things that Jose has done that I have also missed in the past. Really think this should be a regular thing or video series. Especially if you’re helping younger people with engines and parts. Amazing video series that I would definitely watch. God bless you and prayers for Jose’s engine block… lol

@twatdidusay304 5 месяцев назад

Sir, you have earned my utmost respect 👍💯. Thank you for helping Jose out. We need more people like you to teach these skills . Alot of guys are very selfish about sharing their mechanical knowledge. Just an awesome job man.

@Imarookieatthis 5 месяцев назад

I was told at a really young ages that Knowledge is useless if you don’t share it. I Appreciate your honesty and understanding but mostly your honest intentions to help a fellow young builder.

@koreywilliams4570 5 месяцев назад

I had to change from that stock carb. The genuine mikuni was a game changer. That thing is amazing.

@tradesmithedc 5 месяцев назад

I used to work for ARC racing in the machine shop and you wouldn't believe how awesome it is to see all those machines running at once.Theres a great group of guys that make those parts for everyone. Shout out to PJ, Swayze, and Brian! You should do a shop tour of their facility down here in Albany Ga soon

@samsnephew3209 5 месяцев назад

Res Beard, that is the nicest thing, giving him a block. I hope you hit the lottery for being so nice.

@ol-man-duffyj688 5 месяцев назад

We love Red beard and his beautiful wife we never see that’s holding the camera so so steady for all us viewers! 🤙🏼

@tmonster2247 5 месяцев назад

Much Respect Red Beard & Mrs Red Beard for helping Jose’ out!!! This channel is educational & Fun My 12 year old is inspired by y’all also

@robertjohnston4554 5 месяцев назад

When I seen the bore after the first pass I was just screaming noooo.... I just knew the dingle dangle hone wasn't gonna get it. But Jose I give you credit must ppl wouldn't even try to build a stage one kit

@AyGrom 5 месяцев назад

So nice of u to look over his engine for him. Show's what kind of person u are. Redbeard is the mini bike king!!! Stay blessed bud!!!

@kevinsellsit5584 5 месяцев назад

You're a class act Mr. Red. Mr. Beard is pretty cool too.

@LudasGarage 5 месяцев назад

I went down a road like this kind of similar. I can't 100% tell, but that piston looks like a mono ring piston. I also ran one of those and had severe blow by in no time. The next rebuild i did on mine i switched to a dual scraper ring Wiseco piston and haven't had any issues since. Hope this gets to ya in time Red Beard!! I do believe between a mono and dual scrapper ring Wiseco piston; pin heights are different. if I remember correctly from a 3.707 to a 3.595 length rod, factory crank. Happy Building !!

@3lbtrigger 5 месяцев назад

To be honest, it's best to make mistakes on these engines. Yes it's money, but not expensive. I had a Pro engine builder explain the roles and reasons for when to use the ball hone vs the "puck" style. If the cylinders have been checked and verified parallel and true round, the ball hone is best. The "puck" style hone is best to check the cylinders for waves. There's more to this, those are just a couple examples he gave me.

@JSparrowist 5 месяцев назад

Big Bearded Dude doing Jose a solid! Much respect, brother!

@jesseshelby4383 5 месяцев назад

They all have a little bit of metal in them. Right? 😂

@dodgeme1986truck 5 месяцев назад

A little in the oil yes alot I the oil no

@charlesgraham9954 5 месяцев назад

good on u for helping Jose out. yes, we all are ignorant our first time.

@koreywilliams4570 5 месяцев назад

The magic school bus has taught us it needs 3 things. Fuel, air and a spark.

@rossdelauro6908 5 месяцев назад

Forged pistons, such as Wiseco, require extra bore clearance for the expansion of the piston. Factory hyperuetectic pistons do not expand at the rate of a forged piston. Wiseco pistons tend to have a lot of taper from the skirt to the top ring land; I would measure to ensure that most of the aluminum didn't come from the piston. More than likely, the bore is tapered, and piston clearance was not checked during assembly. Oil rings intersecting the pin bore are typically used in long rod or stroker applications.

@jamesseddon4829 5 месяцев назад

Hey bud, just started watching your vids, found you through Cars n Cameras vids. I think it's awesome you included your subscriber and helped the guy out with his engine. That's a great personal touch that I think is missing from RU-vid. Shows you genuinely care and go out of your way to spread the fellowship beyond just being a mouthpiece on the net. Much respect, you earned a subscriber here. God Bless.

@acurarl9929 5 месяцев назад

Totally awesome you guys are helping out a subscriber with his failed engine build. Great wrk and super great to see ppl helping ppl

@anthony1113 5 месяцев назад

Excellent video…absolutely love the level of detail and explanation. Cant wait for part 2…maybe you can Jose to do a follow up video when he gets it back.

@941GKFAMILY 5 месяцев назад

I’ll will dropping a vid when Mr Red sends it back - Jose

@danielfalcon7148 5 месяцев назад

Now I’m vested in this build great video

@StaticSift 5 месяцев назад

you never learn if you dont try. hopefully this encourages him to learn more. need more people willing to teach and help rather than put others down. subscribed to this channel for sure.

@quevicular 5 месяцев назад

cleanliness is godliness. If the carb was lean because of the jet/emulsion tube plus the possible vacuum leak, could it have possibly ran lean this way and done damage to the piston as well. So hopefully the rod didnt get slightly pounded and bent.

@tmonster2247 5 месяцев назад

CONGRATULATIONS ON 400,000 Subs

@RedBeardsGarage 5 месяцев назад

Thank you! Couldn't do it without all of you!!

@migs610 5 месяцев назад

Wow! You’re awesome for helping Jose out! God bless you

@SeanSteggs 5 месяцев назад

Excellent Vlog. 100% should be doing more of these. Learning way way more with this engine over a perfect build.

@matersworkshop6123 5 месяцев назад

Not only do you show what needs to be done when building an engine but also what not to do. Thank you for all of the information that you put out

@trashandtrail 5 месяцев назад

I appreciate the tear down and lessons learned here. Nice job and do more!

@robertdillon4491 4 месяца назад

Hey, good on Jose for doing as much as he did. Thank you for taking this engine on. It’s great content and shows us how detailed you can be on a build like this. Also how easy it is to miss these things. All my best.

@robsdeviceunknown 5 месяцев назад

This is a wonderful video. God Bless you brother for helping this young man out. If more men were like you just think of how good this world would be. Lets all look out for eachother.

@Brad26843 5 месяцев назад

Jose, we all learn. This is a learning experience, please dont let the little things stop you. Learn from this and keep going

@941GKFAMILY 5 месяцев назад

It definitely lit a fire under me to keep going and start my own group here in my area to help others that’s Forsure - Jose

@inventivemachinist8747 5 месяцев назад

Excellent and high quality videos! These are great sources of information and family friendly! Much respect to Greg and his entire family

@CODOutdoors 5 месяцев назад

Wow, you the best Greg, taking your time to help Jose with his engine! Can’t wait for the next video!

@arcane2827 5 месяцев назад

You truly are an amazing builder. I just finished this build off of the 224 full stage 4 build and it was a true relief to see it run. If i have any issues i will be refering directly to these videos. Thank you so much for the time and effort you invest in what you do. Next is a V-Twin full billet build

@jeeper426 5 месяцев назад

classic hotrodding, "build it, blow it up, and build it back faster than it was before" otherwise known as "Trial And Error" you learn from your mistakes, no shame in trying and failing, the issue occurs when you fail to Try, Jose you tried something new, and you put yourself out there, no shame brother this is how you learn, thank you Greg for showing us all what items to keep an eye on and out for, and as a wise man once said "you don't know what you don't know" i hope Jose enjoys a fun hobby and isn't disheartened by failed parts, trying and failing has no shame, thats a valuable learning tool, stay safe out there y'all

@OGTtom 5 месяцев назад

That's great Greg sharing knowledge to a person new in the hobby , we all learn .

@chuckwalker4149 5 месяцев назад

Only a minute into the video and I’m seeing an expensive billet side cover and a stock carb. Money spent in the wrong place. You gotta start simple and with priorities. I sometimes judge the FFA small engine repair competition and it always boils down to compression, fuel/air, and spark, in the right amount, at the right time.

@jerrywilcox9890 5 месяцев назад

No he didn't lol.

@victorbellan8357 5 месяцев назад

Nice dissection & commentary!, thanks for sharing !

@KD16288 5 месяцев назад

Loved this video. I’d like to see more like it. Great job Greg.

@terryharleyrides6109 5 месяцев назад

Thanks for sharing,…..your positive input means so much to so many. You are a great teacher,…Good Stuff 👍😎🙏

@TrulyUnfortunate 5 месяцев назад

Good vid!!! Nice to see you help a dude out. Looking forward to seeing how it runs when you're done.

@timkern462 3 месяца назад

Really decent of you to help Jose, it's great for us that you agreed to do the autopsy and share it with us. With all this work, I'm surprised that he's using the weenie little carb. Even the fake 22 Mikuni would be a huge improvement, particularly if he matched the ports (a 40% increase!) and then spent some time tuning it. Watching #2 now...

@bigpermsgarage6290 5 месяцев назад

Awesome video! Thanks for giving back.

@jondavidmcnabb 5 месяцев назад

Excellent video, I love how you are teaching attention to detail. Many times that is what trips people up when doing projects. Showing all of your steps was a great way to teach.

@MFU.team.4367 5 месяцев назад

Crazy how a simple problem can get a nice build hung up. My hemi had a valve piston make out session and still ran with a bent valve. I tried for hours to re-tune it before deciding it was time to strip it down and start building it from the ground up again. Sometimes when thing don’t work you gotta just admit that something’s wrong and restart. Saves you a lot of frustration at the expense of some effort

@danielrheaume3072 5 месяцев назад

Great video! Looking forward to the 2nd part.

@chrishughes9223 5 месяцев назад

Awesome. My son and I are just getting into this hobby together. I love to see videos that help others learn things to do and not to do. We all learn from each other. Thanks for posting all of your videos. Can’t wait to see the outcome.

@aarongrabowski3775 5 месяцев назад

You were close Jose. Don’t give up brother. You got this.

@941GKFAMILY 5 месяцев назад

Thanks man Gregs blessing and all you guys comments it’s most deff a huge motivation to push further - Jose

@sammylisasmith2104 5 месяцев назад

This is nice of you RBG thanks for your time

@bryduhbikeguy 5 месяцев назад

Because I've been watching you for years,and have seen what you do with it,I have 5 different cans of PB Blaster products,and you're right about them being good. Thanks for showing this 'tear down and checklist' for our builds.Jose did do some pretty good work on it,and yes,we all forget something along the way.We don't forget twice after the lesson's learned.Some of the metal crumbs are probably cylinder lining and the skirt.

@slimyelbow 5 месяцев назад

Love this type of video. Hope there are more to come.

@randyharden5149 5 месяцев назад

Cannot thank you enough for making these videos !! my son and myself have gotten into kart racing in my Five-year-old grandson is our driver. We have just about completed our first season of racing, and I am wanting to get into building his motors. I am extremely thankful that I found your channel. I have gone back and watched a couple of your videos, but I am most definitely starting at the beginning of the road to horsepower. Thank you again and PLEASE keep the videos coming !!👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻

@SHFlameHead1 5 месяцев назад

Great video! Currently building my 212 and I can’t wait to finish it.

@cjjernigan3276 5 месяцев назад

Such a great vid and good deed you did for the young man. Very lucky have ur engine rebuilt by RBG

@goldCrystalhaze 2 месяца назад

You've got one more subscriber, just because you are a decent guy and helped this kid! Congrats to you!

@paulbudford 5 месяцев назад

Great video. Great to help out guys that are struggling. Jose will be learning a great deal from this. as well as many others.

@RedBeardsGarage 5 месяцев назад

Hopefully it fuels him to continue on!

@cldiver-nickgajowski2092 5 месяцев назад

Thanx for sharing your know how and tips!

@dv7431 5 месяцев назад

Good on you, Greg .

@MCscarfacematt 5 месяцев назад

nothing wrong with making mistakes thats how you learn. in high school my first year in shop class we toredown a 212 we had to take it completely apart like you did here and put it back together. now i had an upper hand there because i had years of building racecar engines by then. but when it came to building a 420 for my golfcart ive screwed a few things up. my excuse now is that im now working with one hand. the way i save money building small engines is to play the market and bulk buy parts when the usd is low and cad is nigh

@jewberg7729 4 месяца назад

i love tbe road to hp series so much. youve got me inspired enough to start building. my own cart and bike. im building a 212 swap rt100 frame. i always come to your channel for advice on things im tryin to do

@72151 Месяц назад

Awesome job helping people out like this!!!

@nicholasmarshall3881 5 месяцев назад

This is the best video I have seen in a long time. It’s awesome to see you guys go above and beyond for one of your followers. I’m now a fan!

@edwardfoist5776 5 месяцев назад

Love the videos man I've learned so much from your videos I've rebuilt my dirtbike go cart etc from your tips keep it up!!!

@greggdsciotto8952 5 месяцев назад

Thank you Blaster!

@jaredmcquiniff6174 5 месяцев назад

This is why I have so much respect for you! God bless!

@amandarego9684 5 месяцев назад

That's cool you're helping this dude out

@Skiridr22 5 месяцев назад

I appreciate you for this, it’s why I keep watching this channel because this is someone just like me that you inspired

@ratoneJR 5 месяцев назад

Thanks for helping this guy out. You da man.

@derekkennedy7346 2 месяца назад

You are an awesome person it's great to see that you give back and you help people out for free keep up the great work and I'm going to keep watching your videos

@carlr.2322 5 месяцев назад

Greg you are a good man for all you did to help just subscribed keep it up!!

@Swoliecanoli 5 месяцев назад

Always informative. God bless

@RATTL3R186 5 месяцев назад

Cool of you to help homey out. 👍

@d.b.2812 5 месяцев назад

Teaching others is a great thing.

@jeffbrown8292 3 месяца назад

Just surfing and ran across your video and have to say, hat's off to you Sir! You now have a new fan and keep the educational videos going. Thank you

@ianellithorpe5918 5 месяцев назад

This is a great video! A good path. God bless RBG!

@scootergem 4 месяца назад

Lots of facts, information, and knowledgeable advice. Thanks for sharing.

@RedBeardsGarage 3 месяца назад

Glad it was helpful!

@bluntz_for_4206 5 месяцев назад

Great detail wouldn't mind watching more!

@georgehill6569 5 месяцев назад

You are doing a great job helping him out like that

@Sim_racer_40oz 5 месяцев назад

Nice 👍 thx helping a bro out .

@justinwilson4860 5 месяцев назад

Awesome video thanks for doing this. Really liked seeing your troubleshooting process. And thank you Jose, I know it was probably frustrating for you but we all get to learn from your experience.

@941GKFAMILY 5 месяцев назад

It truly was but hey you get threw things sometimes all you need is a little push , glad my troubleshoots can lead someone else in the right path thanks to RedBeard and his wife 🙏 - Jose