My Shop Vac Cyclone combo changed my life!

Подписаться 18 тыс.

Просмотров 12 тыс.

50% 1

Here you can see how to combine a shop vac with a cyclone. It is a KÄRCHER WD6 shop vac I combined with a small cyclone. It truly changed the way I clean my workspace, a must-have!
You can get all my plans here!
www.etsy.com/se-en/shop/Desir...
Chapters
0:00 The reason for this idea
1:22 Taking the shop vac apart
4:22 Building the upper part
15:00 The shop vac intake
15:45 Modifying top
17:30 Fitting the cyclone
20:23 Starting to assembly it
20:56 This is what I have improved
30:40 I BROKE IT!
31:11 I fix it!
32:32 Some final words

Наука

Опубликовано:

11 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@DesireToInspire1 2 года назад

I need good some suggestions on how to make it more stable to prevent it flipping over because of the added hight. How would you fix it?

@Isarwinklermartl Год назад

Hi, first of all: I just came to this video and think, it is a great approach! Thanks a lot. To reduce the danger of flipping, you might increase the weight of the bottom parts. A thick metal ring around the collection bucket, some stone between the four rolls below the collection bucket... This of course will make it heavier, however, this machine is primarily not meant to be carried, right? Thanks again and best regards from Bavaria 🙂

@JustinShands Год назад

Easy, use it for sanding concrete and it will naturally get much heavier on the bottom :)

@kurtbilinski1723 2 месяца назад

How about adding weight to the base, like maybe a 1cm plate under the bottom? Another option - and a lot more work and expense - would be to make a new version that uses a low-profile separator. That would allow collapsing down the assembly by quite a bit and helping with the balance issue. That said, if you're happy with it as-is, I vote for the plate weight solution.

@kurtbilinski1723 2 месяца назад

@nateb4543 Год назад

For the first time in my life, someone made something more complicated than i did. Yours definitely looks better

@KMvrtr 2 года назад

I really like the small footprint.

@ynot3575 2 года назад

To prevent damage when you flip it over by accident, you could make a wooden ring that sits around the four legs in the middle. So it will flip on the ring and wont break the engine part

@DesireToInspire1 2 года назад

Thanks for the advice!

@awt 2 года назад

It looks like it is full of sawdust, but you said you were originally inspired to make it after sucking up concrete dust. How well does your design work on finer dusts like concrete, plaster etc?

@DesireToInspire1 2 года назад

It work very very well. Only a weak ago i had to cut up my concrete floor and it just sucked it up like a champ :)

@nateb4543 Год назад

Ive got a similar setup, and the fine stuff still gets through and eventually fill up your filter. The difference between my 1st and second versions was easy access to both chambers. It's still worth it 3X. Just dont expect the cyclone to get everything

@brileyroe456 8 месяцев назад

Do anyone know the cost of materials for this build?

@andersbystrom3421 2 года назад

Kanonvideo! En fråga angående dammsugaren.. Har du upplevt att du fått stötar (statisk elektricitet) av det rostfria röret när du använder dammsugaren?

@DesireToInspire1 2 года назад

Oh ja! Riktigt otrevliga sådana, så pass att hjärtat hoppar till, de smäller till högt! Dammsuger jag mycket blir jag nästan rätt för att ta i röret för att jag vet vad som kommer hända.

@andersbystrom3421 2 года назад

@@DesireToInspire1 Jag funderar, kan det hjälpa att jorda röret på något sätt? Tänker kabel till element eller så. Som du skriver, det blir obehagligt efter ett långt användande.

@DesireToInspire1 2 года назад

@@andersbystrom3421 Jag har testat det och satt kabeln i jorden på maskinens uttag, det gjorde ingen skillnad, kanske jag inte gjorde de nog bra...

@niklasfransson5606 2 года назад

Vart köper du så tjock plywood i Sverige? 😊

@DesireToInspire1 2 года назад

De var 5 år sedan jag köpte det och jag vet att jag inte hade köpt en hel skiva. Jag tror det var ifrån snickeriet på Beijer bygg, en så kallat spill bit, kan rent av ha fått den gratis :) Var tvungen å mäta den nu av nyfikenhet, 20mm !!