NISSAN 350Z AUTO TO MANUAL TRANSMISSION SWAP HOW TO!! PART 1 THE TRANSMISSION PART

Подписаться 28 тыс.

Просмотров 46 тыс.

50% 1

Ive been asked to do automatic to manual swap on Nissan 350z and G35 and so, HERE YOU GO!! Part 1 The transmission part. Ive decided since the videos are roughly over 20 mins, viewers like you can now more easily find the exact part you need answers to by searching the category. Either transmission or Part 2 will be the pedal assembly and hydraulic side!! CHECK IT OUT!!!! And for those who have inquired, 🤙
PARTS LIST NECESSARY:
-Cd00x Transmission -Manual Driveshaft -Pivot Ball for Shift Fork -Shift Fork -Throwout Bearing -Slave Cylinder -Clutch Pressure Plate -Clutch Disc -Flywheel - Flywheel bolts (8x) -Pilot bearing FOR manual -Slave Stainless braided line to hardline - Hard line from Master Cylinder to slave line (on drivers side front wheel well) -Clutch Master Cylinder -Clutch Pedal -Manual brake Pedal -Shifter WITH spring and plate to bolt to transmission w/3 bolts -Rubber shift boot to cover trans tunnel -Cloth shift boot -Shift Knob -Manual Shifter trim
G35 WITH FOOT PEDAL E BRAKE ALSO NEEDS:
-Removal of Foot brake -Hand ebrake - Ebrake cable for hand brake (from manual G35)
-Center Console for Hand brake (from manual G35)
My Instagram: @the_crooked_king

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 228

@lucasferreira9648 3 года назад

Literally dm'ed him less than a week ago about tips and tricks for a swap and he drops this video, actually mind blowing. thanks aaron, hope u droop part 2 soon. i appreciate it

@Thecrookedking15 3 года назад

❤❤👊🏻 PART 2 out tomorrow🔥 Thank you my dude, and thank you for the love and support💪 Im sorry if I lagged on getting back on a DM I try to get back to everyone, just busy lol all love brotha

@gregorybraylen343 3 года назад

Sorry to be offtopic but does any of you know a way to log back into an instagram account..? I was stupid forgot my password. I love any tips you can offer me.

@geraldwesley2617 3 года назад

@Gregory Braylen instablaster =)

@gregorybraylen343 3 года назад

@Gerald Wesley I really appreciate your reply. I got to the site on google and I'm in the hacking process now. I see it takes quite some time so I will reply here later with my results.

@chaseholliday9509 3 года назад

You just relieved so much stress off my shoulders bro! Iv been trying to find a video that’s this specific and helps me just like this! Haven’t found a single video where they tell me exactly what I need and then the install!

@Thecrookedking15 3 года назад

Haha HELL YEA!!! Glad I could help!!!! ❤🙏💯💪Get it my dude and if you got other questions hit me up on my Instagram DM me!!!!

@zerohourdrift 3 года назад

Isn’t that Gustavo’s car?😂 never mind you said it right after the intro 😂

@Thecrookedking15 3 года назад

Lol Yessir it is🤙

@dirtyr1937 2 года назад

Ok i have a rev up motor with low miles but the motor is blown. I got it like that. I have a vq non rev up AT. I want to put my 6mt into my vq. Can I re use all the parts when I swap. ?

@lovettgaither7967 3 года назад

Great video! The AT pilot bearing kicked my a**. I bought/ returned / bought bearing pullers that all failed. Then , the bearing puller I rented flexed too much and would come out on the 2nd /3rd hit. I had to tag in help to get my pilot bearing out ... I'm also convinced that I need my own shop space for my hobbies. Keep putting out quality content.

@robertcortinaz7539 Год назад

What’s the charge for something like this?? Very interested

@Thecrookedking15 Год назад

Dm me on INSTAGRAM and we can figure it out💪🏼🤙🏼

@euclidesestribi9008 Год назад

Hi Aaron, I'm looking into doing the trans swap and I would need the ECU mod, is there any information you could share with regrading the guys that do this upgrade, maybe share with me the contact and thanks again for such an amazing content you are throwing out there for our community.. Hands down brother!

@thatduude2835 3 года назад

In doing a manual swap on my g37 . Would i be better off using the ecu and remove NATS, or buy an engine harness for manual and require the whole thing ??

@Thecrookedking15 3 года назад

G37 is different for me tbh, I think you could use the ecu and jump the "park" switch to allow it to start like how the z was jumped terminals by the battery, I am not certain tho, havent done the g37

@alexisnieves780 3 года назад

no you dont need swap the ecu you can use your

@jimenezjr1114 3 года назад

Can you list all the manual swap equipment cause I wanna do the same thing plz

@Thecrookedking15 3 года назад

I laid it out in the video but Ive gotten that question more than once so that might need to happen....

@phreaktor 3 года назад

I tallied up all the parts on eBay new and used and it comes out to $1600 with tax and shipping for everything here except the clutch pedal which I’m looking for now. That’s with a new trans.

@dancingwulf3351 2 года назад

I found one of those transmission forks when I was younger a thought it was an ice scrapper. mystery finally solved xd good vid💯

@Thecrookedking15 2 года назад

😆😆😆😆 def mess your window up LMAO, thank you so much!!❤

@bobpinter3394 2 года назад

what about replacement of the automatic harness to a manual harness? Getting check engine light.....

@bobpinter3394 2 года назад

"wiring"

@cnetplus Месяц назад

can I get someone to take off NATS from nissan teana j31 ecu please.

@MistahPokeymon 3 года назад

Hey man would love a link to your IG in your video descriptions im sure we 350Z noobies all could use some advice/help

@Thecrookedking15 3 года назад

Done! Thanks for the suggestion brotha💪

@5zu-der3 3 года назад

Finally swapping to manual😂

@Thecrookedking15 3 года назад

😈💯yessss!!!

@JoshDucote Год назад

Hey man i was wondering what was the total cost of this conversion? Thanks!

@steambuns2283 3 года назад

ngl been watching some of your vids and your intro was a banger.

@Thecrookedking15 3 года назад

🙏🙏🙏 thank you so much!!

@itsmeyaboi1830 3 года назад

I’ve been waiting for a video like this! I’ve wanted to swap to a manual for a while now but had no clue how to go about it

@Thecrookedking15 3 года назад

I hope it helped🙏🙏Let me know If you have any questions about it, you can message me on here or DM me🤙❤

@trevormorgan6538 3 года назад

So is changing out the drive shaft neccessary I've watched some other videos and they didnt say anything about it?

@Thecrookedking15 3 года назад

They have different lengths 🤙

@sirjankalot1963 2 года назад

Where you located, i want to manual swap my 2006 g35

@youarethealgorithm 2 года назад

How much should this cost? I want to swap my M35 transmission.

@BigBoyz33 3 года назад

bro i didnt know you had a youtube channel LMAO subbed fr tho

@Thecrookedking15 3 года назад

Haha yessir WELCOME!!! and Thank you brotha🙏🤙❤

@brianvilla5464 3 года назад

U think u can make a list of every thing we need for the swap Ik u laid it all out in the video a list would be helpful tho thxxx

@Thecrookedking15 3 года назад

DONE!!! all love brother THANK YOU THANK YOU🤙🔥 Check in the description of the Video👊🏻

@louiscanas1082 5 месяцев назад

can someone please tell me what grease or lubrication he was using

@diegofeik1306 Год назад

I just found out I was doing everything wrong lol

@marklengal9990 Год назад

Will this work on a G35? I assume it will, but I had a shop tell me I needed the motor and trans combo and ECM. Not sure why I needed a motor to match the manual transmission

@Thecrookedking15 Год назад

Definitely will and no motor needed. I don’t understand that either lol just the transmission and manual stuff💪🏼

@realmistahwong 3 года назад

Hexa Garage can do nats delete? How do I get in touch

@Thecrookedking15 3 года назад

Hexa motorsports on Instagram and talk to Jorge or Jake, rad dudes and super knowledgeable💪 They are located in santa rosa👊🏻

@exige3604 3 года назад

Hey Crooked Crown...I have a 2004 Zzz with a VQ35 DE automatic. Where can I source these parts to do the conversion? After driving with the automatic, get kind of boring...even though in LA...heheh. Are you in California? There are several videos on RU-vid with this conversion, your video, was easy to watch....step by step! Like to hear back, your thoughts Sincerely..thanks! New subscriber 🏎

@Thecrookedking15 3 года назад

WELCOME my brother and thank you🙏🤙 Im actually from southern california, Valencia actually but located in Nor cal in fairfield ca now. I sourced a lot of my parts just from pick and pulls and yards with nissan/infinity. ebay is also good for getting parts because they can ship to you from anywhere in the country. Hope that helps, hit me on my dm on IG if you need any other help. all love

@marlonlegra367 Год назад

Can I use the ECU from un g35 is the same year ?

@dynastycrew824 2 года назад

Don't know if you'll respond but is this the same process for a g35 like all the same parts you explained in the start of the video and where all the bolts are mounted and coolant lines

@Thecrookedking15 2 года назад

Yessir. 🤙🏼I haven’t found anything really different except if it’s a sedan with a foot brake ebrake you’ll have to remove it for the clutch pedal. If you got questions dm me on ig @the_crooked_king. I try to respond all the time. Much love man

@milliondollaboiibsb4927 3 года назад

Love the channel fam u and myke are my inspiration with this car shit my guy blessings your way hope ta drive wit y'all one day

@Thecrookedking15 3 года назад

Thank you brother🙏🤙your support keeps us going , appreciate you, much love💪 ❤

@aeok18109 3 года назад

Great video. It's that the csc delete kit?

@Thecrookedking15 3 года назад

Thank you!!!

@EduardoZacarias-ox7go 3 месяца назад

My clutch will not pop all the way out

@DeJuvn 3 года назад

I have an auto Im not swapping my transmission yet but I am putting a new de in and I noticed that there was no pilot bushing?!?! Idk what to do im stuck lol. No one talks about auto cars🥲

@Thecrookedking15 3 года назад

No pilot?!? there isnt a big aluminum one pressed into the end of the crank?

@sawmebabe 3 года назад

This is why I'm subbed. Nice.

@Thecrookedking15 3 года назад

🙏🙏thank you my dude!! 👊🏻

@gerodriguez1993 2 года назад

How can i manual swap with a vhr trans on a g35

@lonewoofv 3 года назад

after swapping the trans did you get the U1000 code? im having that problem, i bought the car swapped so idk if the ecu was programed

@Thecrookedking15 3 года назад

Yesss that code is a communication code since the ecu was programmed for the swap

@stevegarcia521 10 месяцев назад

Is this the same for an HR tranny ?

@theoterei7508 3 года назад

Oh man getting the old automatic pilot bearing out is a pain!.. when you don't have the right tools 😂

@Thecrookedking15 3 года назад

Bruh seriously, even with the right tools, still fights 🤦‍♂️

@theoterei7508 3 года назад

True 😂 bloody pilot bearings

@mauriciogutierrez7997 3 года назад

@crooked crown motorsport I have a question can I use the ECU out of any Manuel z

@Thecrookedking15 3 года назад

Yessir just need the nats flashed off it, so the immobilizer doesnt stop the car from starting🤙

@Jacob_A1 3 года назад

Those ratchet wrenches are amazing we got a set too

@Thecrookedking15 3 года назад

RIGHT?!? lol hell yea Love them💯💪

@ugandanknuckles464 Год назад

just making it slower

@medicali8318 3 года назад

About time to get ride of that there is no feeling of shifting gears and being in control of your car its a feeling only so few know keep doing ya thing and I will hit you up to do some work on my mustang just don't tell my wife lol I have a feeling with your info and mikes and mine we can make my mustang one of the fast in my country 😉

@Thecrookedking15 3 года назад

Haha for sure man, Thank you so much!!! Keep me up on the progress!! all love brother

@medicali8318 3 года назад

Yea looks like ya are good guy and hella fun to be around the next time ya buring tries let me know i would love to stop by and check out your guys shop if thats even a option

@phreaktor 3 года назад

Aaron why is that slave cylinder braided line so short compared to all the ones I’m seeing on ebay? Thanks -T

@Thecrookedking15 3 года назад

so there is a hard line factory that runs from the master down under the driver wheel well cover and to the trans area on manual g35/manual 350z, the customer bought that hard line and then we just put an upgraded slave cylinder line from the hard line to the slave. If you get the one from ebay or amazon or something like that, the long braided line cuts out the need for the hard line and goes directly from the master to the slave🤙

@phreaktor 3 года назад

@@Thecrookedking15 Thanks I figured this out after more research.

@JoseDemetrioGonzalez 3 года назад

Good video, I love how you explain every detail, I have never found a video like this that explains step by step I look forward to the next video I don't care how long the next video is, you have all my interest, good job🙌🏼

@Thecrookedking15 3 года назад

🙏🙏🙏❤Thank you Thank you so much!!!! Appreciate you, all love🤙

@eyeamfresh82 3 года назад

Glad to see the lift working 👌🏻🤙🏻🤘🏻👍🏻

@Thecrookedking15 3 года назад

🤦‍♂️About time right, LOL😂 thanks for noticing....... lol

@overipecolt246 3 года назад

That's awesome that little bro got all his stuff together to swap it , get part 2 out soon

@Thecrookedking15 3 года назад

Hell Yea, been putting it together for a while now too, its finally DONE😈👊🏻🔥 Part 2 Out tomorrow at 9am🤙

@jakegoats1916 3 года назад

how much do you charge to do this swap?

@sirjankalot1963 2 года назад

How much did you charge him

@issawrx7772 3 года назад

Anyone know where I could get a manual crossmember?

@Thecrookedking15 3 года назад

I have one if you need it

@pav8105 3 года назад

Is the clutch hard line different on right hand drive 350z?(uk)

@Thecrookedking15 3 года назад

I believe It is but dont have a definite answer for you, ill have to check that out🤙

@Conker999 3 года назад

I'm swapping and manual trans from an 08 to a 07 Z are the engine harnesses different?

@Thecrookedking15 3 года назад

Nope should be the same🤙

@Conker999 3 года назад

@@Thecrookedking15 is a manual harness a plug and play onto an auto engine? Sorry this is my first time im going to do something like this so wanna make sure I have the right parts

@Thecrookedking15 3 года назад

@@Conker999 the engine doesnt matter as long as the 02 sensor plugs are the same, however the manual and auto harness are different plugs for the transmission, the engine will all plug in but when you go to plug in trans if you have manual and have auto harness or vice versa, the transmission sensors wont plug in and you wont have some functions of the car, like reverse lights etc

@Conker999 3 года назад

@@Thecrookedking15 okay perfect that I have the manual harness then I should be straight. I'm going to replace trans internal slave cylinder and upgrade the clutch while I'm doing it 👌 thank I appreciate you

@phreaktor 3 года назад

@@Thecrookedking15 So you need a complete wiring harness from a manual as well? Sorry for all the questions.

@brokenbonesme13 3 года назад

Wtf I click on a random video and it’s white aaron

@Thecrookedking15 3 года назад

Haha HELL YEA ❤🙏thank you brotha, all love man always

@adamfakhouri9088 Год назад

Can this guide be used for the 2008 350z. From factory the 2007 and up have a JK41B 6 speed.

@johncorrea240 Год назад

Do you know when swapping a 350Z HR from Auto to manual is there a way to turn off the service engine light because mine popped up I did not swap the ECU to Emmanuel one I have a manual ECU but I have not plugged it in do you think plugging in the manual one will turn it off

@ardellreeves1481 3 года назад

What type of grease do you use on pilot bearings/input shaft/throw bearing

@Thecrookedking15 3 года назад

High temp bearing grease💪

@entosthia 2 года назад

I know I’m late to the party but you have saved me 🙏 much love bro

@Thecrookedking15 2 года назад

LOL better late than never...💯💪🙏 appreciate that man, much love always💯🙏❤

@brokeblasian 3 года назад

Are you able to do this for my car? Just started buying parts for my manual swap but wanted to find someone who could do it properly.

@Thecrookedking15 3 года назад

I can, and would love to help you!! Let me figure out shop stuff first to make sure there is space and availability to do it and Ill get back to you!! Much love man!!

@brokeblasian 3 года назад

@@Thecrookedking15 sounds good man ! It’s no rush right now I haven’t been able to get my hands on a cd009 trans and I’m slowly stacking up on the other parts.

@rolandomota2289 3 года назад

Ok so my car is at the mechanic right now and it needs a new engine. Can an engine from an auto be used with my manual transmission and be made to work?

@Thecrookedking15 3 года назад

Yessir. Same engine. Just change the pilot bearing to the manual trans pilot bearing and everything else works normally

@rolandomota2289 3 года назад

@@Thecrookedking15 mine is an 06 manual. I think I read on the forums that its not the same for the 06 manual rev up.

@6speed87 3 года назад

how much the swapped cost this video is 🔥🔥🔥

@Thecrookedking15 3 года назад

Thank you man!!❤ about 1500 In parts and I charge 1100 for Labor 🤙

@funnycovers5543 3 года назад

@@Thecrookedking15 $1500 in parts!! My list tallied up to $6900?!?! :(

@phreaktor 3 года назад

@@funnycovers5543 what is that all new OEM parts? I’m at 1600 minus the clutch pedal and hardlines.

@user-qc5te9wk1s 3 года назад

I have been looking at a z for a while I rlly want a manual but I could easily get a automatic z for lower miles and cheaper price I am in high school love to learn and I am thinking about getting a automatic and maybe doing a manual swap u think I could do it by myself? I think I could probably but not sure sense I have never done it only think is is I don’t have a car lift

@asunainori6475 2 года назад

Question.. so ive heard that manual from factory is better than tranny swapping it. Is the true or does it just depend who does it for you? cause I have a 350z but i want it manual

@AcMus1c 3 года назад

Pedal Assembly next please! im having trouble with my brake pedal lol

@Thecrookedking15 3 года назад

Its in part 2, DROPPING TOMORROW at 9am🔥👊🏻

@Thecrookedking15 3 года назад

Hoping Part 2 Helped you with your pedal!!! All love man🤙💪

@theyhatedanny2282 3 года назад

I don’t even got a z and I watched the whole video 😂

@Thecrookedking15 3 года назад

😭😭❤🙏🙏🙏🙏🥰Appreciate you So much man Thank you🤙 All love man

@wassupdummy 3 года назад

first or nah

@Thecrookedking15 3 года назад

Im not sure....... 🤣

@OTFOGZ33 2 года назад

Aaron let me get that auto shifter till I go manual hahahaha plz I'll pay shipping

@Thecrookedking15 2 года назад

lol I dont have it anymore man sorry......

@OTFOGZ33 2 года назад

@@Thecrookedking15 😢 lol it's Kool love ur videos man

@CoreyJ92 3 года назад

So the vq in the 09-15 maxima can be manual swapped, no one has a video on RU-vid doing the build would love to see you pull it off an help me do it on my own maxima

@danfrancis7258 3 года назад

That’s what’s up bro good looking out on showing how to do it. Btw happy New Years!

@Thecrookedking15 3 года назад

Happy New Years bro!!!! lol glad you enjoyed it, Thank you so much🙏❤ all love always

@ryovaIorant 3 года назад

I got an AT trans light after my conversion, is it because the car is not able to sense the automatic gearbox? what should I do about it

@Toysourboy 2 года назад

People keep telling me to just trade the car in or buy a new one. I ain’t giving up that easily.

@Mmmmmmmm-mm2zt 2 года назад

Would it cause grinding issues if the automatic bushing wasn’t removed ?

@victoriaphipps5340 2 года назад

What is the man time for this? Is this like a 2 day project or can it be knocked out in one day

@geremiavelasquez5933 Год назад

Thank you daddy

@flazowk1881 2 года назад

1000th like keep up the content!!!, also thanks for showing and describing the swap.

@anthonywimberly4567 3 года назад

Did you have to swap out the pilot bushing ? Or did you run the auto one ?

@Thecrookedking15 3 года назад

Yessir you HAVE to switch the pilot bushing🙏🤙

@anthonywimberly4567 3 года назад

@@Thecrookedking15 how did you go about the neutral safety switch?

@staytrucivic3710 3 года назад

Hell yea man good for that kid!!

@Thecrookedking15 3 года назад

❤❤❤

@ThatBustedVQ 3 года назад

he should swap in a manual diff as well autos use 3.3 manuals use a 3.5 or he could throw in a 370 3.7 diff

@2coldproductions896 3 года назад

The into hahahaha

@Thecrookedking15 3 года назад

lol❤

@kurtdogg8685 3 года назад

Mean vid bro good work

@Thecrookedking15 3 года назад

🙏🙏👊🏻thanks my dude

@tylerj7107 3 года назад

Do u know where he got all the parts from because there’s a lot of parts and I can’t find all of them as of now been looking into it for months

@carsten-qr6xt Год назад

Thanks for you work! My 18yr old son and I are completing a swap on his 08 350z and are at the crank/ no start stage. Wondering if it's essential to swap the ecu to manual (it's currently still auto) and what other wiring we may have missed. Thanks!

@Thecrookedking15 Год назад

Hey I’m so sorry to just be getting to this man!! THANK YOU THANK YOU so much. And no it’s not necessary for you to swap. And auto works as long as you jump the wiring like in the part 2 video💪🏼🤙🏼 hope that helps man. Can’t wait to hear about it being done. Much love always❤️🤙🏼

@elcopeton1978 Год назад

@carsten-qr6xt Did you ever finish that swap on your 2008 im trying to do my 2009 350z in the next couple weeks

@carsten-qr6xt Год назад

Got it done! Struggled with the wiring a bit but everything else went smoothly.

@3TITTYZ 8 месяцев назад

@@carsten-qr6xt what did you have to wire? I want to get into this swap but soon as i hear wiring i get intimidated lol, how hard was the job?

@carsten-qr6xt 7 месяцев назад

The only wiring is splicing into the wire that controls the park neutral switch so that the computer allows the car to start. The mistake we made was cutting the wire rather than splicing into it as the video demonstrates.

@alx9950 2 года назад

If i was looking to swap my transmission do you think i should do it myself or have it done somewhere and if so should I go to some sort of specialist or can almost anywhere do this

@DriverModJess 3 года назад

Glad to see the lift is finally working. I’d hate to swap a car on the ground.

@Thecrookedking15 3 года назад

Gah its the worst😒im spoiled now with this lift lol🤘🏻❤

@jeremyjames2606 3 года назад

I did it on jack stands wasn’t hard at all.

@iTzDeXx_Dc5 3 года назад

Never realized how many parts go into a manual transmission 🤯

@Thecrookedking15 3 года назад

Right?!? lol 🤦‍♂️more than I thought initially too lol

@vergevision1943 3 года назад

How much does it cost to do a manual swap on a 03 350z?

@Thecrookedking15 3 года назад

Its about 1500$ in parts and I charge 950$ for labor

@BBCforyoHoe 3 года назад

@@Thecrookedking15 do you think it’s worth swapping it in 2021? People are saying 350’s are going up in price so maybe it is worth it at the end of the day instead of selling it?

@twill5313 3 года назад

This camera loud as hell

@Thecrookedking15 3 года назад

hmm, I try to turn down the volume some but overall I cant control the pickup volume, sorry man

@aristobaldosocrates1981 3 года назад

Hello, I have an 06 350Z, which is VQ35DE 5AT, 280hp, I'm going to a single turbo on it, with Transgo kit, I got few questions and since I live in Brazil is veryvery very hard to see people who understand of this car, even on forums like my350z My biggest problem is the transmission, I was looking for another transmission to put in, but in Brazil we pay 100% import tax over the product + shipping price, so if 2k usd for the cd009 + 500 shipping I pay 2500 + 2500 usd. Usually people wage here is 120 to 200 a month, of course I'm not like those peoples but I'm not rich if I put my money in USD's So basically I have 2 questions to know where should I run: 1- Any other transmission that I could find to swap even if I need adapt few things? Like Nissan Frontier 6MT? Which year could be good? Or any other? 2- How much power can the 350z 2006 5AT transmission handle with Transgo? I was looking for 500whp or something close to it, you think the transmission with transgo will handle that? Or should I jump for a swap ( but there is not even one 350z transmission to sale in whole Brazil ) I'm sorry for taking your time but I had nobody else to ask those things...

@philspaghet 2 года назад

I'm not the creator but see if you can get a T56 or LS based manual transmission. There are a lot of swap kits for putting those into Zs and some manual Z drivers swap those in because they are stronger than the CD00A in the 350z.

@Mohammed-lw7bm 2 года назад

can you explain more of why you changed the eco?

@kaseyvaughn5963 2 года назад

Clutch disc is a top hat. Put the top hat on the engine

@drdingleberri1643 2 года назад

Man I can’t find anyone in socal to do a swap for me ! No shops want to do it lol

@VQDNZ 2 года назад

There’s a few in socal.. i can give to their instagrams. Im Gonna end up doing it myself

@drdingleberri1643 2 года назад

@@VQDNZ ya bro if you can I appreciate it

@stefmcquack1934 3 года назад

20:04 that's what she said

@Thecrookedking15 3 года назад

😆🤣🤣🤣🤣😆💯

@erosnunez4256 3 года назад

This video helped me swap mine. You saved me tons of labor money thank you!

@Thecrookedking15 3 года назад

Great to hear! Youre welcome brother!!!! hell yea!! much love🙏❤

@Bryan-jb8ky 2 года назад

@@Thecrookedking15 how much is the conversion?

@fruitfulfigtree2195 3 года назад

When Swapping Do You Need To Swap Ecu From That Engine To A Car That Came With Manual ??

@seangraffis7361 3 года назад

No you don’t. There’s a wire you need to splice on the IPDM that will trick the car into thinking it’s always in park to start. I’ve done this to my Z and never had any problems. This is the link on how to wire it my350z.com/forum/engine-drivetrain-and-forced-induction-diy/552038-5at-to-6mt-swap-info-diy-guide-thread.html

@arisonperez1974 2 года назад

Can I fit a 2004 tranny on a 2006 z?

@v_az_qu_ez5027 2 года назад

Hey so if I changed out the ecu and engine harness for an MT harness will that allow me to have the reverse lights and clutch safety switch as if it was stock? Or do I still have to wire stuff.

@v_az_qu_ez5027 2 года назад

Also does flashing the ecu help with the codes and the check engine light so that it can pass inspection? Ik here in PA if they even the light they fail inspection