Nissan Titan Exhaust Manifold/Header Replacement (2004-2015)

Подписаться 56 тыс.

Просмотров 241 тыс.

0% 0

If you have found this video helpful, and you wish to donate to me, follow this link!! its easy!!
paypal.me/aaronhinesauto?loca...
Follow this channel on twitter for the latest content updates and weekly Automotive Tips!!
AutoHines?lang=en
In this video, i show the steps and procedures necessary to remove and replace a cracked exhaust manifold on a Nissan titan, these steps can also be used on a Nissan armada and infinity qx56 vehicles. years 2004-2015. This is a extremely common issue with these trucks. the job is long and difficult at times, but with the right tools and tips show in this video. The job will be a little bit easier. i hope this video helps you out, if it has please like and subscribe. if you have any questions or comments please leave something in the comment section. thanks for watching!! Below are parts and tools i used in this video.
---------PARTS USED IN THIS VIDEO------
exhuast nut (8)
www.courtesyparts.com/oem-par...
exhaust manifold gasket (2)
amzn.to/2DmypD
exhaust manifold to pipe gakets (2)
amzn.to/2V9ztoB
intermitate pipe to y pipe gakset (2)
amzn.to/2ULPrWE
stock style exhaust manifold:
amzn.to/2XsSU9A
14mm deep well swivle socket:
amzn.to/2GrDaN5
Best aftermarket supplier of Long tube headers:
STAINLESS STEEL-
amzn.to/2DyBa59
Ceramic coated-
amzn.to/2Zjoqbz

Авто/Мото

Опубликовано:

2 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 325

@aaronbritt2025 4 года назад

BTW, you don't need to cut or remove the heat shield. Unplug and unclip to O2 sensor wire first. Then, after unbolting the shield, lift it up on top of the coils. You have to shove it up there and tweak it slightly. You can lift it high enough to get to all of the manifold bolts. When you're done, pull it back down and bolt it back on. This works on both sides. It's how we do it at the dealership.

@AaronHinesAuto 4 года назад

Thank you for this info!! U the man

@kill2ski 3 года назад

Can I remove it entirely this way without cutting it up?

@aaronbritt2025 3 года назад

@@kill2ski You can remove the heatshield entirely, but you'll have to bend the s*** out of it.

@yungavalor3192 2 года назад

@@aaronbritt2025 possibly stupid question but would I NEED to replace the heat shield with a new one once I replace my manifolds? If that is too hard to do I don't want to waste any effort. My new manifolds didn't come with one.

@aaronbritt2025 2 года назад

@@yungavalor3192 no reason to completely remove your stock ones. You unbolt them, push them up and replace the manifold. Then you pull them back down and bolt them on the the replacement manifolds. It's actually harder to completely remove the heat shields.

@DarrelllCampbelll 8 месяцев назад

Thanks for the video. I was able to replace mine in 19 minutes also

@eduardocalvillo5658 Год назад

Wow, and shops want to charge over 2k for this job. Ok I’ll keep the truck and getting under it as soon as order the manifolds. Thanks a million.

@wakeuppeople6446 4 года назад

Your video was filmed with good details. Thanks for putting it up on YT. Good job, nice work & keep putting them out, they are very helpful. THANKS

@emiliosoto6545 4 года назад

So I just did this job on my titan it has 220,000 miles on it and the bolts look like they havent been removed since day one. I used 2 cans of BP blaster and it took 3 days total to do the job as it took one day to just take the bolts of and another day to remove the old headers and reinstall the new ones. Day 3 was looking for the lugnuts my father in law lost and I had to buy new ones. So to sum it all up never doing this again. But thanks for the video it was helpful. 😁👍🏻

@viorelnaidin5933 5 лет назад

Hey Aaron! Thank you for your videos,working on the Titans! They are time and money saving for me! God bless you sir!

@anthonysnipe9876 4 года назад

2008 nissan Amanda belt pattern

@n.elliott9122 Год назад

Really appreciate the detail and patience you put into to making this video. You gained a new subscriber.

@lcar9871 4 года назад

WOW Aaron -- Great video!! - Thank you sir!! I was just looking at this job yesterday - 2008 Pathfinder with (I believe) the same VK56DE V8 engine. It needs a PS pump so I have the inner fender off for that. It also developed a leak in the passenger side exhaust manifold. I'm looking at the engine and reading the Service Manual (which has me removing the entire front drive axle assembly) -- thinking there HAS to be an easier way, and you just confirmed it. I found your very well done RU-vid video this morning. You even list the needed tools. Very thorough indeed! Of course here in New England, the heart of the rust belt, there will be a lot more cutting, cursing and torch work. Maybe some welding too - the exhaust flange bolts look like toothpicks. Here's hoping the manifold fasteners come off ok. I will be sending a small donation your way and hope others are doing so too. Videos like yours are so helpful in so many ways. In this case it confirmed my thoughts that the manifold could MAYBE be repaired this way VS the Service manual method of pulling the whole front drivetrain out. Thank you! Larry

@JAMESJJEFFERS 5 лет назад

So Far Probably the Best and Most Inspiring Walk Through I've seen YET in any videos.. Good Work and Thank You.. Although living on the East Coast in Jersey with almost spell "Difficult Knuckle Busting Rusted Bolts" I'm sure!!! 💪😊

@AaronHinesAuto 5 лет назад

Thank you! Good luck with that rust!!

@farrardk 3 года назад

Impressive. Very impressive. Thinking I'm doing this instead of pitching the repair shop a few weeks of my wife's pay check. ;-)) Thanks for putting together such a high-quality vid!

@tonybroderick6590 5 лет назад

Great video. I will definately use this for my exhaust replacement. Thanks

@JAMESJJEFFERS 3 года назад

Thank You for this. About to replace the entire system and also live in Jersey so rust will make this more of a headache. Good Video!!!

@edwinthomas618 3 года назад

Excellent video. I used it as a reference for my 2006 Armada 2wd on Bank 1 (LH) side. Take top of air filter box and flip over on the engine to get access to 2 motor bolts. I separated the steering joint to the steering CV joint. Trying to take the lower portion that connects to steering tack was an issue since it was splined and I didn't have a tool to get it off...so I left it. Regardless I worked around it...if you have huge hands it might be an issue. The heat shield came off without cutting it as it slide out from the top of engine compartment. My manifold bolts were rusted a little and I soaked them with CRC Knocker Loose over night. I took my time and they came off except for 1 bolt that needed heating. FYI... If you are doing one side and lifting the engine....my suggestion is to jack up the truck level because when placing wood under the oil pan and trying to jack the engine when it is tilted is not a good idea because there will NOT be direct contact across the oil pan when jacking up engine. It took me a day and 1/2. The little Milwaukee rachet was a life saver. I did a little things differently but your video was so helpful and a life saver from $1700 being paid..thank you sir.

@BIGTONE-lc4vd 3 года назад

This was a excellent video. I have seen a few for this particular type of truck. please make more for this truck

@treadmillgamin 2 года назад

Thank you! I was fighting with my '05 Armada for a minute, and not finding a good angle of attack. I hadn't thought of going in from the wheel wells, and also now own an impact 14mm pivot socket to make the job easier. Fortunately, I'm experienced enough now with breaking things on vehicles that I only rounded off one bolt partially before I said "This isn't working..." and came to find this video!!!

@Tankslayer109 2 года назад

At least im not the only one

@deltabravo5719 3 года назад

You made a big job look easy. Nice work.

@mistertellez2434 3 года назад

Your videos somehow make it seem pretty doable for one who is not a mechanic. At least the videos help me understand the basics of braking things down to small processes. Thank for the videos.

@ismailbaksh1411 4 года назад

Yeatarday i replace LHS exgust manifuld and iys take my time 6 hrs my good then i found this video and now its very easy four me .bcz i have to remove and replace gaskit RHS alsow thx.

@steveschneider2112 3 года назад

Super well made DIY video Aaron!

@samsturbo 3 года назад

Very clear and informative....thanks

@vmeed1732 4 года назад

VERY WELL DONE VIDEO! Nice balance of detail! Nice touch listing all of the tools required, that 7/8 wrench had me curious at the beginning. Excellent that you pointed out using new OEM nuts and gaskets, that's a DIY nightmare waiting to happen, strip them off half way and then have to wait for days for the dealer to order them. The length of the video was perfect, you edited the unnecessary parts, and didnt talk forever about things that are obvious! I did catch one edit that made me chuckle..... that first O2 sensor... you said something like.... just press the release and pull it apart... you fumbled a little and then the video was cut and magicallyit came right apart! ALL of us have fought with one of those stupid connectors that refused to release like it should! Awesome video, keep up the good work! God Bless you and your toolbox!

@felixFPVDrone 5 лет назад

Great job! Excellent tutorial special for those of us who have Nissan Armadas/Titans. My check engine light came on at about 100k, I had the mechanic check for codes. He told me more then likely the catalyst converters need it to be replace. The more I follow this issues in RU-vid, and other forums it leads me to believe my exhaust manifolds maybe crack (I haven’t actually inspected them). However, it seems Nissan has done a good job building heavy duty vehicle, but some of their OEM parts need improvement! Again thx!

@dakotacresswell7270 4 года назад

felix44860 just checked mine today and sure enough a huge crack around one of the tubes, getting it repaired and hopefully the issue is resolved, repairing existing headers is more cost effective than replacing

@lovelife3628 4 года назад

They use aluminum when they should have used cast iron. I have heard they can weld the crack rather then full replacement. Some shops can weld them without taking them off.

@kill2ski 3 года назад

@@lovelife3628 I was thinking about welding mine, how much did they charge you? My passenger side is a little noisy but not bad, been like that for 3+ years since I got it. Wouldn't pass emissions even though I have no codes or I/M readiness, this is BS!

@tcbkkb1 5 лет назад

Great video man! Keep em comin’ I have 06’ from day one and shes still goin strong!

@chrishall5346 Год назад

I had some Jba headers replaced for same price of factory headers on my titan to a banks monster exhaust. Sounds great that's not an easy job to do he made it look easy.

@boydguie8129 3 года назад

Nice job . Great detail.

@veegee1974 5 лет назад

Super helpful! Just got a new sub.👍🏾

@AaronHinesAuto 5 лет назад

Thanks for the support!

@scottrose5922 2 года назад

Great job, thank you for sharing. My 2011 Titan has 83,000 miles. No major issues. This will definitely help if I ever experience this

@vhsfever4794 Год назад

Thank you! Excellent information!

@Mike-vt6is Год назад

Thanks for the heads up on the gaskets I got mine from Nissan as well as the studs and nuts i rounded off the nuts on a couple of mine but was about to use easy outs reverse nut grabber on a swivel. Well more than a couple like 6 or so lol.

@jimboboheem Год назад

I just finished your video man, by far the best video out here on this. Thanks for your hard work and keep up the good content! Helpful man

@briangay5418 4 года назад

Great video. I have a northern truck and will have to have the professional do it due to rusted bolts.

@buggscarrot9557 4 года назад

I know my vehicle is a new york vehicle and when i do it stuffs gonna break.

@Koz1ov3 4 года назад

You should be on the road doing this all over the states

@redboy1400 3 года назад

I met someone in San Diego that does it for living

@mikeriv60 2 года назад

Thanks. Titans are very good vehicles.

@oscarestrella5241 3 года назад

Great job man

@stevenlsobel 3 года назад

I just replaced my drivers side...it was a bear doing it on a sloped driveway on the ground. But your video was super helpful. I got the heat shield out in one piece, but didn't put it back on...hmm...should I bother?? Great job

@mikerasmussen7367 Год назад

Excellent video!

@danielkustra9071 5 лет назад

Thank god for a recent video. I have an 05 with 218k on it. It's got the dreaded tick and I was hoping to replace the gaskets and call it a day. But it's looking more and more like the manifolds. I may go the long tube header route and call it a day. Thank you for such an informative video. I'll definitely need to watch this a couple times to get better idea before i dig in.

@AaronHinesAuto 5 лет назад

good choice with the long tube headers, i have a seat of doug thorleys on my 04, i have installed a set of jba headers in the past and you cant go wrong either way. ium glad you found the video helpful. if you need any help during the install, just ask!!

@troygould1493 4 года назад

@@AaronHinesAuto I need my 04 done. I'm in mesa

@jn9434 5 лет назад

Great video. I have a question on the four engine mount bolts. I am having an issue getting to the rear upper bolt. Is there a trick to getting to it? It’s funny all the videos on you tube skip showing how to loosen those four bolts. Thanks for your help.

@moneybags7064 Год назад

this is going to blow

@slip0n0fall 3 года назад

Minor suggestion - plug that dip stick hole because of all the rust/garbage/sprays you'll be dumping down that side of the engine.

@ksenskittens3263 5 лет назад

Just did the passenger side on my 06, went better than I thought! Is there a video for the driver's side?

@uhmeizuhngralphf0549 3 года назад

Cool very nice 👌 headers

@m.b8257 3 года назад

Great video .

@hennessygaming3051 3 года назад

Great video once again and thanks for taking the time to reply when im sure you gey swamped with questions. ive used your tips and tricks for almost every part of my titan over the last 2 years. One quick question if i replace my bank 1 manifold/cats with OEM manifold do i need tuning afterwards?

@cryptoenthusiast8218 5 лет назад

Awesome video! Keep it up!

@AaronHinesAuto 5 лет назад

thank you for the support!!!!

@t10k7 4 года назад

@@AaronHinesAuto you're the man brother great job!

@bryanmartinez6600 5 лет назад

Me: Looks easy enough Me 6 Days later: *Dropped Transmission and Transfer Case* I'm thinking of doing the AFE twisted steel with their rebel series cat back exhaust.

@kyflyboy965 2 года назад

Thanks for this video! I just put new manifolds in my ‘06 Titan 4wd. I am not a professional mechanic but have done the service on all my vehicles for 40 years. This was one of the most frustrating jobs I’ve ever done! If I could offer any advice to anybody else thinking about tackling this project it would be to remove the 4wd differential (axle assembly), the frame cross member, and the motor mounts. I needed to replace the lower a-arms so I was already into it and had the steering knuckles already off. After I got the a-arms off I went ahead with the manifold replacement while I was at it. After doing the passenger side, I took a good look at the drivers side and realized it was gonna be a nightmare unless I removed the stuff I already mentioned. After taking those items off and finishing the drivers side, I wished I had done that first before even doing the passenger side. It made it much easier!

@MGdriver77 4 месяца назад

I'm here to do this work on my Titan soon. Thank you for the tip

@repairdroid77 2 года назад

I've done this to my 04 armada and it's exactly the same process.

@angryretrogamer4735 5 лет назад

Man I need you to do my 2009.

@Dettdu 2 года назад

Good job

@OG213LA Год назад

Dam… I was going to do it myself but after seeing how much work it is I rather just take it to a mechanic. Thank you

@metalitubbies 4 года назад

That engine bracket is the pain part!!...lol

@Matty-_-Patty00 5 лет назад

Just replaced my OEM intake with a K&N Series 77 filter (checked multiple times to make sure its snug and not leaking) and ran it for a day then the SES light came on. Looked and seen a P0174, tried cleaning the MAF sensor and erased the code then after driving for a bit with my scan tool connected a P0172 code came up checked for vacuum leaks nothing to report there although I did notice the crank case vent hoses didn't have any clamps connected and were very loose to pull off the valve covers so put on some clamps erased the code and going to see if that worked tomorrow. And while I put the clamps on I decided to get under my truck and listen for any leaks in the exhaust or the headers, sounds like above my upstream CAT's there may be a crack somewhere. It's hard to hear from the radiator fan but I think that might be just the problem. It sounds a bit louder on the passenger side than the drivers side. Might as well go with some JBA's and straight pipe cat back if that's the issue :) If you have any info what it can be happy to read out the possibilities and check it out. Edit: Also going to replace the Crank Case and PCV hoses to make sure. They've seen better days haha!

@alouiciousjackson5812 Год назад

Those last two bolts can be removed with a wrench. Place the 14mm box end on the nut, and place the box end of a slightly larger wrench on the open end of the first wrench. Also, to prevent future failure of the cat a proper break-in procedure should be done: after idling for 5 minutes, run it up to 1500 RPM for 2 minutes. Then let it cool completely. This expands the catalyst material.

@jzur49 Год назад

Great video. I have a 2005 Titan with all the original exhaust components besides a cold air intake. My question is what kind of sound will this make if my headers are bad? My truck is lifted 6 inches and has all terrain tires but I feel it's gotten louder inside the cab this past year even after I got new tires not that long ago. I have 190k miles and it does not show any warning lights on the dash. I'm in Avondale AZ so if your still in Surprise I would be willing to drive out to you and you tell me what you think in person.

@benjaminreidy9753 4 года назад

How come the link to the bolts say they won’t fit my 2012 Pro4x? Btw great video, I’ve been sitting on my parts for a year cause I’v been too chicken 💩 to start this project on my own. You make it look easy. Great job!!!

@harleylee4381 4 года назад

Is this the best time to install new engine mounts as well? I have JBA LTs, Cajun b pipes, and PRG engine mounts ready to install, just trying to find the easiest way to install these mounts.

@danielkillebrew4557 2 года назад

Great video! Do you know where I can find the studs for this job too? Exhaust manifold to cylinder block right?

@mynors8713 4 года назад

Im glad i came across your page. I have an 06 armada that needs a lot of work, and my son and i are using it to learn few stuff. Now, my son wants to be a mechanic, and your channel is out go to page. Please, DM me if possible, i have a few questions. I will definitely out some money for your time.

@VaporheadATC 3 года назад

A word of advice for anyone installing JBA long tube headers. Tighten the engine mount (frame side) after removing the old manifolds! With the new JBA headers installed, one of the downtubes completely blocks access to one of the 17mm bolts.

@JOATJESSE 2 года назад

Awesome advice. Installing some this weekend and you saved me from the "SOB" moment that we've all been through.

@VaporheadATC 2 года назад

@@JOATJESSE No problem. I should have mentioned it was on the drivers side.

@ramsesfelix388 Год назад

Question about JBA long tube headers upgrade. They come with no catalytic converter and OEM cat is one piece with heaters. So what type of cat can i use with JBA headers?

@VaporheadATC Год назад

@@ramsesfelix388 Does your state test for emissions? If so, you are out of luck most likely. I don't run any cats with my headers. Cajun offers a catted b-pipe setup, but those are your secondary, "downstream" cats which don't play a role really.

@blakeallen2189 3 года назад

Any reason you didn't use the impact gun to remove the 8 nuts on the manifold? It seems like using the impact gun would prevent the chance of rounding the nut (not having to push the breaker bar (keeping it tight on the nut)while trying to turn it), but I was curious to get your input. Great video.

@ryanphillips3533 2 года назад

I realize it's been some time ago unfortunate but I'm getting ready to have this done along with the rest of the exhaust system to my 2005 qx56. Do you remember what brand this set up is and where you purchased it from?

@HK-el4xv Год назад

Thank you

@lovelife3628 4 года назад

I wanted to know is there any cast iron after market exhaust manifolds for these 04-10 Nissan trucks? Also if I replace these parts with the parts you recommend is it possible they will crack again? Thans for the vid great job!!!

@njoeandjen Год назад

Great Job and tips mine i had welded at a shop and i used old gaskets cleaned them all up runs great now just when i first started it had a lot of smoke for a couple minutes then seemed ok is that normal just burning off maybe a lot of spray residue ??? Thanks!

@hardset-vi3ze 2 года назад

Sweet!!!!!

@northern3000 5 лет назад

Wow, for you southern mechanics working on cars is like playing lego. I almost started laughing when i saw you remove an exhaust bolt with a impact ratchet on an 11 year old car. I just did this same job on my 2008 QX56 with 180,000 miles and I would have loved if my bolts would have come out half as easy as yours :)

@dateatorjr9671 5 лет назад

northern3000 tell me about it. Each step for me is about an hour or more and usually involves a sawzall or grinder 🤣

@stapleboss 4 года назад

I've done this job at 140k in New England and it was no joke. Next worse is the lower control arm cam bolts fused into the bushings. Also, if you get the JBA LT headers (I did) you gotta get the Cajun B pipes w or w/o cats and tuning to make it work right.

@playtimewithkeshawnboi3509 3 года назад

Good afternoon did use the link for manifold exhaust because my mechanic say it can’t work with modifications?

@ibuki56 2 года назад

@jeffharris6323 2 года назад

@@stapleboss same here in Utah. cam bolts were fused to the guide bushing in the lower.

@MichaelHatfieldFlowers 4 года назад

The manifold you installed looks different than the link you posted, can you comment with a link to the exact manifold you installed, need to replace both on my wife’s 2010 armada.

@tim_798 8 месяцев назад

Hi @aaronhinesauto! Could you update the links for your recommendations on the long tube aftermarket headers? Thanks!!

@uhmeizuhngralphf0549 3 года назад

👍 nice

@nemesisa64 5 лет назад

I need someone to do this jon on my 2005 Titan... any recommendations in the tri-state area? NJ?

@justtogetby5903 3 года назад

If reusing OE manifold how necessary would getting it milled flat likely be? Hate to do this again for a warped manifold instead of just a weak OE gasket. Do the MLS gaskets have a enough sealing ability that milling is mostly unnecessary?

@pedrodavid4442 3 года назад

I need some advice I did a check engine light on my truck and it showed that both of my upstream oxygen sensor are out do you have any idea why that happened??

@johnfloyd2551 2 года назад

Is there shorties(not stamped manifolds) available out there with cats and flanges on already?(bolt ons).. only finding longtubes stock manifolds cats and open end shorties..

@MakeItMike 4 года назад

Would it be beneficial to put antiseize on all those studs and bolts?

@adongarcia9063 4 года назад

Kind of related to this..question,the catalityc you took off was the passenger side right?..does that catalityc considered the BANK 2?

@joshuacastillo8238 5 лет назад

You sir are a boss brotha! That little Milwaukee impact looks like a life saver. Btw is this a 2wd? I've got a 4wd 06 and eventually need to do headers. Always hear that 4x4 is harder.

@AaronHinesAuto 5 лет назад

no, the truck shown in the video is a 4wd. not very fun with the axle and diff directly below the manifolds. makes a 2wd look like a cake walk. get yourself a 1/2 ratchet that swivels like the green one show in the video. the motor mount bolts that go into the block are hard to get to on the drivers side. that milwaukee awesome. i got it at home depot. thanks for the kind words!

@edwinthomas618 3 года назад

@@AaronHinesAuto is the driver side engine mount bolts hard to get to because its 4wd or do think it will be so with 2wd as well?

@betosn18 5 лет назад

I am from Phoenix az when can i take my truck to you to have this done it is an 2010 2wd

@ismailbaksh1411 4 года назад

After replace gaskit engine warnig light is showing how i can remove engine light without .IT.bcz i dont have IT

@beastfromtheeast9318 4 года назад

I did this already. I actually think replacing the starter is harder than this.

@itzmckrispy9318 3 года назад

I am personally never doing a starter on my Titan again 😂 I’ll let the shop deal with that hastle

@kfiscal01 3 года назад

Starter is a hassle!

@playtimewithkeshawnboi3509 3 года назад

I did start on my 04 it wasn’t that hard, my mechanic still telling me that the manifold link can’t fit, did u use the link manifold?

@patwhatley 3 года назад

@@itzmckrispy9318 Had my new starter and took it to a local shop. They quoted me $110 to install it. Apparently they'd never done a Titan before...and from the looks they gave me when I picked it up they never wanted to do one again.

@TheGuruStud 3 года назад

@@patwhatley Starter is easy. Pulling IM/injectors is cake. Why is everyone a drama queen on removing IMs? It's the easiest shit in the world...unless it's a VG.

@mitchwillis5556 Год назад

I ordered the DNA long tube headers. They have 2 O2 ports, one at the flange and One in the back tube. which should be used since the cat is now deleted, to not cause a cel?

@matthewwibbens5957 Год назад

Hi aron i know this is an older video now but the best i have found the links to the headers no longer work i will need full length if you could help me out im struggling right now if you see this it would be a prayer answered thank you sir! Awesome content

@tahiryratsimanohatra9480 3 года назад

Aaron, where did you get the actual manifold that you used in this video? Some of the links you posted dont work :(. Thank you

@dateatorjr9671 5 лет назад

Yes! I been waiting for this one. I have the JBA headers. Saving up for the B-pipes. It’s going to take me 5000% longer though thanks to NY rust. I’m hoping I can get by until spring since it’s my winter vehicle. Those magnaflow manifolds look nice.

@AaronHinesAuto 5 лет назад

im glad! i couldnt imagine doing this job with rust. yikes. i have jba on my 04 and love them. i was impressed with the magnaflows too. they look like shorty headers.

@dateatorjr9671 5 лет назад

Aaron Hines so the Titan threw the CEL today. Got 1146 and 1147. Do you know if they are both for the bank 1 rear sensor?

@AaronHinesAuto 5 лет назад

@@dateatorjr9671 both those codes are refering to the rear bank 1 sensor.. which is the driver side downstream sensor. looks like the computer is seeing an issue with the heater circut in the sensor. if the sensor is original. i would replace it with an oem unit.

@dateatorjr9671 5 лет назад

Aaron Hines thank you for confirming that for me! Do you think it’s something that can wait, being its the secondary o2? The truck doesn’t fit in my garage and the weather sucks right now. Im also doing the full exhaust come spring. I appreciate your time and help.

@AaronHinesAuto 5 лет назад

you bet bud, i appreciate all your support for my channel. yes it can wait. oxygen sensors dont read properly until the are HOT. so they build a heating element into the sensor to help it reach temp sooner. your sensor has an issue with the heater circuit according to the codes. all you need is a 7/8 wrench and some small pliers to compress the connector.

@Jessehernandez83 4 года назад

So if you get this code is it too late or should you worry about the pieces getting sucked up into your engine? Or is that what only happens if you let go too long

@gidderman 2 года назад

Did you ever have any problems with that magnaflow improved design catalyst? Did it perform well?

@Georgia-tb4lz 2 месяца назад

What is the manual way of getting the truck to learn the sequence? I don’t have the tablet to reset codes lol. My armada has a acceleration issue with a smell of exhaust and the codes p0171&p0174

@WAenduroman 3 года назад

What about the driver side? Are there any complications or noticable differences? Every video i see are for passenger side only.

@acuraintegra-1771 Год назад

Will your way of clearing code work with long tube headers?

@trevorjohnson2067 5 лет назад

I seen you wrote you’re in surprise, what’s the labor cost on this if I bring my 06 to you? I can do this but don’t really want to haha. I’m in mesa so not far at all

@dogunboundhounds9649 Год назад

The aftermarket exhaust systems are no longer on sell. Any other recommendations other than OEM?

@avigang9192 5 лет назад

did this on my 06 it sounds great...however i should of used the oem gaskit because now i have to go in and replace it with the oem one....:( it sucks for me. great video thou.

@bryanmartinez6600 5 лет назад

That's why I never touch the cheap aftermarket stuff.

@cattleclerk1 26 дней назад

You have to either remove the studs or unbolt the motor mount from the engine not the frame to have enough room to remove the manifold and gasket

@johnthreesixteen5295 5 лет назад

First great video very detail and informative. Where is the link for the parts you said you would include in the video?

@AaronHinesAuto 5 лет назад

thank you very much! if you click the show more button under my name below the video, that will open the entire description where the links are! thanks again for the support