Тёмный

Oscillating Multi-Tool Tips And Tricks 

Enduring Charm LLC
Подписаться 80 тыс.
Просмотров 1,2 млн
50% 1

The multitool has become a tool we can't live without. Carpenters, drywallers, electricians, and plumbers all have one on their truck and DIY folks have them too. In this video I'll share and demonstrate some of my techniques to get more accurate and cleaner cuts in a variety of materials and show some common uses for the oscillating multitool.
► To Purchase
amzn.to/3gHtGyH (DeWalt cordless multitool)
amzn.to/2zy8URj (DeWalt corded multitool)
amzn.to/2XFcPUg (Makita corded multitool)
amzn.to/3gA3PZ7 (Makita cordless multitool)
amzn.to/3gB5M7P (Porter Cable corded multitool)
amzn.to/36FryCS (Fein corded multitool)

Хобби

Опубликовано:

 

24 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 683   
@preacher1775
@preacher1775 6 месяцев назад
After viewing numerous videos about multi tool, I wholehearted believe this is, by far, the most informative and helpful! Thanks a mil!
@davidderolph2845
@davidderolph2845 3 года назад
I had never owned or used an oscillating tool until about 2 1/2 years ago when I removed some carpet and installed wood flooring and realized I needed to shorten the bottom end of casing around doors so that I could fit the flooring under the door casing to achieve a neat, clean look. By now, I've found numerous other uses for the tool. For example, I recently installed a recessed cabinet in a wall in a bathroom. I used my oscillating tool to cut through some 2x4 lumber that had to be removed to make room for the cabinet. Your tips are completely consistent with my experience.
@bradman1100
@bradman1100 2 года назад
for a diy learner like me, this is brilliant. great teacher. 11 out of 10.
@susanpalmer5598
@susanpalmer5598 3 года назад
I've been procrastinating on finishing a soffit over my kitchen cabinets I installed because there was a piece of molding in the way that has been there over 50 years and painted in etc. Felt it would really make a mess of my ceiling etc. After some research I bough my Dewalt with battery and watched this video that was so helpful and built my confidence to proceed. I'll be finishing my soffit today! It also touched on topics that are so useful, such as the nail removal, not messing up your sheet rock, and removing grout. Thanks for the help!
@kevinxxx1387
@kevinxxx1387 3 года назад
THANK YOU! I bought my first multi-tool a few days ago (I'll probably use it first today) and the FIRST THREE hings you showed are the first three things I'll need to do.
@1nteract1ve
@1nteract1ve 4 года назад
Thanks for sharing your knowledge. You’re a good teacher. It’s unfortunate that the tool manufacturers don’t produce this kind of informative content to help us use tools more effectively.
@philarsenault8537
@philarsenault8537 4 года назад
Thank you John for sharing your experience and skills. My take away is that don’t be afraid to try new things after of course you see how the experts do these things. I appreciate you taking the time to train us neophytes!
@HotRod751717
@HotRod751717 3 года назад
Great explanations with great video close ups! I need to cut a small rotted section of an eve so I can replace it with an equivalent piece of plywood. Watching you easily cut through the 2" x 4" convinced me that the oscillating multi-tool would be the best tool for that job. Thanks very much!
@janpeterson21
@janpeterson21 Год назад
Thanks so much! I’m feeling more confident that, as a woman who loves to craft and try small woodworking projects, I can use this tool. Excellent tutorial!
@Fishstycz
@Fishstycz 3 года назад
Useful tips, thanks. One of my first applications with my multi tool was removing carpeting from the inside of a small cabin boat. I used the scraper blade with astonishingly fast results. I can strongly recommend having one in the arsenal.
@karento8098
@karento8098 4 года назад
I just bought one of these to do some Reno work in my bathroom. Having never used this tool, I found your video very helpful. Thanks!
@karend.9218
@karend.9218 3 года назад
It’s a great tool. Bought it for myself f4om an infomercial I was watching on my birthday, 10 years ago. Used it so many times since.
@drago8613
@drago8613 2 года назад
I bought one to use for repairing water damage on window frames outside. I have never used one. Not so scary after watching this video.
@ianpullman203
@ianpullman203 4 года назад
This is great, I bought this tool to cut out some weathered framing on the bottom of a door way and these tips will make it even easier.
@DavidHodgesKU11
@DavidHodgesKU11 3 года назад
As a trim carpenter my cordless XR is one of my most used tools. Absolutely love it. Pro Tip for those expensive ass blades. With the right file it is extremely easy to cut new teeth and reuse those blades. Especially if you are using them for rough work or demos.
@Fernando.Vivanco
@Fernando.Vivanco 2 года назад
The trick on cutting a line first and then cutting deeper was awesome. Thanks, felt like my Dad teaching me something haha 👍🏻
@brucewilliams6292
@brucewilliams6292 4 года назад
I appreciate the video. These are things one wouldn't think about in the heat of the moment. I'll pay more attention in the future.
@leebarker539
@leebarker539 3 года назад
An artist is someone who knows how their material behaves. Obviously, that is you. This is a valuable video and I agree with the commenter who said "you are a great teacher." There are thousands, maybe more, videos which are total junk. Yours is golden. Onward!
@enduringcharm
@enduringcharm 3 года назад
Thank you for the kind words!
@Lolo-mx4sc
@Lolo-mx4sc 4 года назад
Remember you can save a few $$$ by sharpening/renewing your blades with a triangle file. Just take your time. It really does work. Great video BTW. Thanks
@Wildcat5181
@Wildcat5181 3 года назад
I mostly use a semicircular blade, but I use straight blades to.
@scarlettfire5112
@scarlettfire5112 4 года назад
Thank you for the demonstration, it was very helpful
@danchandler9381
@danchandler9381 3 года назад
Round blade is good during tongue and groove floor repair. When you are removing a damaged plank, round blade helps you avoid accidentally cutting into the neighboring planks.
@bethanyjolee
@bethanyjolee Год назад
Oh wow!! I'm getting ready to do this and that is exactly the type of tip I needed. Thank you!!
@traciebarrass6612
@traciebarrass6612 4 года назад
I love my Oscillating tool, I would be with out it, once you get use to the vibration. But it done an amazing job on sanding my stairs. Great video, thank you for sharing 👍🏽💚
@robscaife589
@robscaife589 3 года назад
Great video, thanks. I've found the scraper blade to be the perfect tool during a bathroom reno to break the seal between the vanity and the wall so I wouldn't damage the wall pulling the old vanity away. Also, loosening the caulked baseboard without damaging the drywall. In both cases the attachments came away cleanly with no tears or gouges in the drywall surface. Also, I'd suggest that homeowners using the tool occasionally buy the corded version, not the battery powered tool. Cheaper, and it will work just as well in 10 years. For someone in the trades or a heavy user the convenience of a battery version will probably make up for the cost and relatively short lifespan of batteries.
@enduringcharm
@enduringcharm 3 года назад
I agree, there are tradeoffs going with battery operated versions. I have both, and I'll grab the battery version for quick work. But, if I know I'll be using the tool all day. then the corded version may be a better choice.
@grb024
@grb024 12 дней назад
I’m going to echo others’ comments: I’ve watched many videos on multi-tool use, as I’m new to this tool, and yours is at the top of the heap. Great tips. Thank you!
@adamcoe
@adamcoe Год назад
Picking up that same Dewalt this week, really appreciate the tip of turning over the tool! Makes tons of sense but I likely would not have thought of it on my own. I've never owned one of these before, excited to see what it can do!
@jimmowers7675
@jimmowers7675 4 года назад
Great info. I’ve been doing things wrong. Thanks for the great tips.
@johnlovell8299
@johnlovell8299 3 года назад
My wife bought this multi-tool for me for some projects. Thanks for this video chocked full of great tips on using it successfully.
@SuperBardley
@SuperBardley 4 года назад
Thanks for sharing. One of your points that I feel deserves serious emphasis is the challenge of heat build up. Heat is what kills the blades and fast. Your scribe the line first, bulk cut second method is one that I use, but I approach that in a more refined manner: Just because one can plunge cut doesn't mean that one must do so; plunging is just another feature of the tool that is most useful when space limitations force us to plunge. Instead, my experience shows that this tool needs to make cuts similarly to how a router is used in multiple shallow passes in order to clear the waste material from the kerf, otherwise the waste cannot get adequately cleared and heats up the blade, which then softens and dulls it. That may be why some of us get mixed results with that drywall blade; trying to plunge it just jams up the waste and creates major friction on the large faces of the blade. Instead, light back and forth passes will work well with its radiused edge to push the waste up and away to the surface of the sheetrock. Here's my tip for those who, like me often work on lath and plaster walls, which are very different from sheetrock: I cut lath and plaster with the carbide grit grout blade because it is very tough and the carbide grit cuts a kerf wider than the blade body. The wider kerf allows the high sand content waste to move out more easily and this prevents heat build up and the blades last many times longer.
@enduringcharm
@enduringcharm 4 года назад
Yes, heat is a blade killer for all types of saws. Also true of drill bits.
@asyntheticsound
@asyntheticsound 3 года назад
i’ve worked at a pawn shop dealing with tools for three years, but i never knew how to really use them beyond testing their basic functionality. i just got a multi tool for home projects, and this video is beyond helpful!!
@rorycampbell6146
@rorycampbell6146 2 года назад
I bought one of these tools a couple of years ago and until now, I could n't really see the value of it. Now, it makes sense, so thanks for that and I will be using it much more from now on
@jesshothersall
@jesshothersall 3 года назад
Thank you, that was a brilliant video. I learned a lot, as am about to buy one of these tools, now feel I'll get better use out of it, much appreciated video
@danalaniz7314
@danalaniz7314 3 года назад
Thanks! The tips are great and the whole video is really informative and your demonstrations are really clear. I love the tip about pointing the cutting edge backward when storing.
@artvandelay1099
@artvandelay1099 3 года назад
Great video. Great tips. I would add just this: if you need to cut a nail, a bi-metal blade is fine, if you absolutely can't avoid cutting a screw, be absolutely sure to change to a dedicated metal cutting blade. Then cut as you described. Going at a screw with a wood or bi-metal blade can ruin the blade instantly. This tip applies to reciprocating saw blades as well. The best thing you can do is remove the screw entirely, or use an angle grinder to cut the screw instead.
@enduringcharm
@enduringcharm 3 года назад
Yes, a lot of people don't realize that some screws are made with a harder, more brittle metal than nails. Drywall screws are a good example. They will ruin blades in short order, so I'll usually try to reverse then out or snap them off from the side with a hammer.
@waynehendricks8187
@waynehendricks8187 4 года назад
This type of tool is one of my favorites. I find this excellent for removing siding on my house as it will go nicely between the boards and cut the nails though the blades do not hold up for long. I bought one that was suppose to outlast all others 20X but found it was no better than HF's but quite a bit more expensive. You mentioned some good tips. Thanks. I did notice you have to be careful when cutting nails for siding as it can heat up and start to smoke. Thanks again!
@enduringcharm
@enduringcharm 4 года назад
Yes, it's an excellent choice for clapboard siding repair. I'll also use a reciprocating saw for that purpose, but if the siding is old and fragile, the multi-tool works well.
@aaudain1
@aaudain1 3 года назад
I agree on that, tools last longer if handled the right way
@ginog4480
@ginog4480 4 года назад
Great info from obviously skilled professional, and very nicely to the point. Thank you
@tonyn152
@tonyn152 3 года назад
Just ordered one of these to help me remove old kitchen tile (saw this technique in another video). I learned so much from you in this video. Thanks for putting this out there are sharing your experience!
@rayb7469
@rayb7469 4 года назад
I just purchased a multi-tool knowing that many of my friends use them a lot. I found your video very helpful, showed many different applications and you spoke slowly and clearly....very useful video and information for me, thanks for spending the time to put it together
@enduringcharm
@enduringcharm 4 года назад
Glad it was helpful!
@tommc49
@tommc49 4 года назад
Thanks for the tips. Doing my research before buying my first one for home shop use.
@stephentaylor1568
@stephentaylor1568 3 года назад
I used my new De Walt multi tool for the first time today after watching your tips and tricks video and was amazed at the results. Easy to follow and just as easy to put into practice. Many thanks.
@enduringcharm
@enduringcharm 3 года назад
Great to hear!
@mjs3343
@mjs3343 3 года назад
Great camera work! Also, I like your detailed instructions and reasoning with pros and cons. I'm a retired professional engineer and appreciate your attention to detail and thorough instruction. I just subscribed to your channel.
@enduringcharm
@enduringcharm 3 года назад
Awesome, thank you!
@outlookfix6859
@outlookfix6859 2 года назад
Very well done. This video shows the difference between a master pro teaching you vs. an armature. Thank you I learned a lot. Well done.
@bizboomer
@bizboomer 4 года назад
Thanks for sharing your valuable knowledge and experience! Very helpful to us weekend warriors!
@grb024
@grb024 12 дней назад
First time in any multi-tool inst video I’ve heard the tip of flipping the tool over, and your explanation why made me palm-slap my forehead. Invaluable!
@andrewbrown8148
@andrewbrown8148 3 года назад
Good info~! I have a Rockwell multi-tool that (sadly) doesn't get a lot of use, so my experience with it is minimal. Your shared tips will be very helpful whenever the need arises for me to break it out. Thanks~!!
@nixonmadrazo4629
@nixonmadrazo4629 4 года назад
great for a DIY newbie like me! thanks a lot!
@AboutThings_byTarif
@AboutThings_byTarif 3 года назад
This is one of the best "tips" videos I've ever watched. Tips are practical, personal, different, applicable to many situations. Well done sir and thank you for all the effort.
@jorgenj1
@jorgenj1 4 года назад
Very good tips. I always have problem cutting sheetrock with the oscilante tool. Thank you for that tip
@mikeh4800
@mikeh4800 2 года назад
Thank you for producing this show. I have learned in 20 minuets what would have taken me years of using the tool.
@davidmiracle398
@davidmiracle398 3 года назад
Thanks for the tips shown in this video. I have a reciprocating saw that I've never used--so far. Your tips for it's use are great, and since I'm pretty much a DIU, I'm sure some job will come up where it will come in handy.
@mjs3343
@mjs3343 3 года назад
Reciprocating saws are great. I'm a DIYer and they are great for demolition or just cutting up debris for easy disposal. I also used it with a 12 inch blade to cut free my vertical door jambs holding my two sets of Peach Tree French doors when we did the basement remodel. Funny, I also have a power tool that is still in the original box and I have not even taken out of the box. It's a very nice HITACHI compound slide saw that I bought nearly 20 years ago for $600!!! I ended up having the hardwood floor installer also cut and install all the baseboards and doorway trim. LOL
@tomflyinghat9122
@tomflyinghat9122 4 года назад
A great video for a complete novice like me. Very helpful thanks.
@dannybouy7948
@dannybouy7948 3 года назад
Tip: for a scraper blade, use a worn wood or bi-metal blade that you grind to a sharp edge on the grinding stone. In so doing, you should never need to buy a scraper blade again.
@keithy.1179
@keithy.1179 3 года назад
I use old carbide blades for cutting metal, rather than reaching for a new one.
@chrisgraham2904
@chrisgraham2904 3 года назад
Yes! Regardless of the make or quality of the blade, they do wear out relatively quickly. Very easy to grind or file off the remaining teeth of an old blade and grind or file a chisel beveled edge to turn it into an excellent scraper. If your typically cutting soft materials like drywall or construction lumber, your wood blades can be easily rejuvenated by resharpening the teeth with a small jeweler's file or I have even cut new teeth with a small cut-off blade on a rotary Dremel tool. You can rejuvenate the teeth dozens of times before you lose a quarter inch of blade length.
@mariad4183
@mariad4183 2 года назад
@@chrisgraham2904 this is awesome! Thank you Chris!
@vanwin5415
@vanwin5415 2 года назад
"SeeJane Drill" on youtube shows how to grind off worn edge and with the right shaped file, cut new teeth.
@davecarsley8773
@davecarsley8773 Год назад
Or just use a scraper blade for tasks which require a scraper blade.
@Johnbro8
@Johnbro8 3 года назад
Thanks for sharing your skills, definitely educational, I’ve leaned some new tips thanks👍
@rickwood2552
@rickwood2552 3 года назад
Recently bought one and is my go to tool for cutting, etc.
@vereferreus5262
@vereferreus5262 2 года назад
Finally a usefull tip weather to get the expensive blades or not...And many more useful tips on the multi-tool. Top!
@stevemiller2957
@stevemiller2957 2 года назад
Thank you for these tips, just got my first multi tool and will be following your advice. Thanks again.
@michaell8835
@michaell8835 4 года назад
Great advice, very much appreciated.
@paulmaguire3594
@paulmaguire3594 2 года назад
This is what I wish most instructional videos were like. As an introduction to the tool and its uses, I can't imagine a better start. Thanks for this.
@enduringcharm
@enduringcharm 2 года назад
Glad you enjoyed it!
@cojimar54
@cojimar54 3 года назад
I had never seen so accurate review! Thanks
@paultant6741
@paultant6741 3 года назад
Just got this tool. Used on 3 jobs. Very versatile and great tool. Thanks for video and great tips 👍 👌 .
@Sparkeycarp
@Sparkeycarp 3 года назад
I like the round blade for depth control on drywall. Trouble is I often have to use the square blade to finish the corners neatly. I am an electrician and have a couple of the box shape cutters for cut in boxes. They are so fast. Thanks for your tips.
@paullanducci440
@paullanducci440 4 года назад
Great video, I've been pushing my blades to hard.
@tcruz86
@tcruz86 Год назад
Great tips. Super instructor. As a retired US Army Officer, your method of instruction is just like how we trained our soldiers. Attention to details and safety best practices. Excellent!!! Thank you sur👍🏽
@enduringcharm
@enduringcharm Год назад
Well, I was Navy, and attention to detail was a primary factor in boot camp as well!
@roho4373
@roho4373 4 года назад
Excellent tutorial! Thank you!
@andrewheathcote2850
@andrewheathcote2850 3 года назад
In England, mine also came with a depth gauge, that fits onto the multi tool, very useful when you are cutting through plasterboard etc.
@goodairin
@goodairin 3 года назад
I needed to remove dried Gorilla Glue from a metal surface that I did not want to damage. After trying so many things, the scraper blade on my oscillating tool worked good. Thanks for the useful tips!
@MzVee106
@MzVee106 8 месяцев назад
Thanks for all of the great information...I just received mine and am glad to have these tips before getting started on cutting some drywall wall.
@ton7164
@ton7164 3 года назад
Your tips are really helpful. Thanks a lot!
@Wbmfishman1
@Wbmfishman1 4 года назад
Thank you. Just started a small repair project on some red cedar clap board. Just chewed up some blades cutting the nails. Now know how to cut them properly.
@enduringcharm
@enduringcharm 4 года назад
Yes, better technique will help. I should mention, though, if I have the opportunity I'll use a reciprocating saw rather than a multi-tool to clip off nails. It's just a better tool for the job--faster and with a more durable blade. And for removing clapboards, you can sometimes pull the nails rather than cut them. If you haven't seen my video on clapboard replacement you should check that out here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-opTPy4Z0uuk.html
@jimmyrodd6476
@jimmyrodd6476 4 года назад
Excellent video John, I'm new to all these DIY skills and this was an awesome and educating tip & tricks video.
@prestondallas4035
@prestondallas4035 2 года назад
Thank you! I just got one of these because I work with pallets and pallet wood. Sometimes I run into problem nails when removing individual boards but cant risk splitting with a pry bar.
@billynomates4378
@billynomates4378 4 года назад
I've just bought a multi tool as I needed to cut chipboard flooring flush with an existing wall that passed over it. I watched your video and used the several passes technique. Result was perfect. Without your advice I would have plunge cut and made a right mess of the job. Many thanks.
@enduringcharm
@enduringcharm 4 года назад
Glad I could help!
@robertgarner11
@robertgarner11 4 года назад
Thanks so much. These tips were super handy!
@dianedesrosiers2057
@dianedesrosiers2057 Год назад
Love it. Thanks. Just bought one yesterday. And your trucs are great.
@dondean2132
@dondean2132 4 года назад
Excellent tutorial, thanks!
@JustaSimplefact
@JustaSimplefact 3 года назад
Used a super worn out metal cutting blade, to remove mortar from bathroom tile that needed to be re-set. worked like a charm, better than any other option. Save your trash blades, sharpen a few on the bench grinder. Also you can use a triangle hand file to resharpen (wood) blades. (maybe metal if your triangle file is super legit.)
@jsmcguireIII
@jsmcguireIII 4 года назад
When trimming baseboard I screw a scrap piece as a straight edge on the waste side so I'm not free-handing what needs to be a perfectly straight cut. Then just rest the blade flat against the straight edge.
@11855alan
@11855alan 3 года назад
I’m in the process of reasoning all my trim work in the house. The tricky part coming up is the wainscoting butts up to the existing trim and the new trim is 3/4” wider. Your idea of using a trim guide is what I was thinking. What would be the best way to control the depth of the cut? The wainscoting is 1/4” over drywall. Any thoughts?
@davegordon6943
@davegordon6943 3 года назад
@@11855alan put a piece of tape set to the depth you want on your blade. If you need to go a half inch deep then measure a half inch up the blade and put the tape there. When you reach the edge of the tape, stop.
@JohnHallgren
@JohnHallgren 2 года назад
@@davegordon6943 the last blades I bought have depth markings on them but it can rub off after some use.
@tomtom786
@tomtom786 4 года назад
Great demo, thanks for the detail !
@realpatriot5896
@realpatriot5896 3 года назад
I have a cordless Kobalt that takes the universal blades. However, I also have Bosch cordless and the Bosch curved starlock blades are awesome compared to using straight blades when cutting wood and drywall to make nice clean straight cuts.
@kahotam7975
@kahotam7975 3 года назад
thanks for sharing your experience! I'm thinking of getting one for some loft DIY work.
@customer7903
@customer7903 3 года назад
Thank you for taking the time to produce this video - really informative.
@sk66G
@sk66G 3 года назад
That's awesome how you explain the way things work. That helped me a lot. Thanks and please continue. I subscribed.
@BL-yj2wp
@BL-yj2wp 3 года назад
For sanding with these I have found that, probably due to the limited movement, fine grained sandpaper works better than coarse stuff. 120 and up they do quite a decent job.
@TheFlutecart
@TheFlutecart 2 года назад
Yup- the heavier grits just kinda clog up and leave scorching. It's a finish sander at best. But also a finger sander with the right attachment. You can sand just the tiniest spot.
@laverdajota8089
@laverdajota8089 4 года назад
I have had two parts of my life , before multitool and after multitool, best bit of kit I have (Makita)
@davidburne9477
@davidburne9477 4 года назад
Used to ride my brother’s Jota a fair bit........30 years on he still has it and it’s going back together after a Redax engine rebuild. On the subject of multi-tools, I bought one recently as overhead sanding by hand of my window frames was killing me. With the sanding attachment I achieved more in half an hour than I had in the previous 6 hours....used a few sheets, but still better than by hand.
@laverdajota8089
@laverdajota8089 4 года назад
DB , the Jota was always my dream bike when I was 15 , always wanted one, never happened , other things took over my life , but I can still remember the first one at full chat down our road , me and my friend rushed down to see what it was . Still remember it , it was a silver one , then after that all I did was dream of having one , ah well , never mind . Enjoy playing with your multi tool.
@raminybhatti5740
@raminybhatti5740 4 года назад
So true. I bought one last year at the beginning of renovating my house, and 12 months on it's become my favourite tool ahead of my circular saw and a chop saw. It's so versatile.
@johnchampion7819
@johnchampion7819 2 года назад
I've just bought a multitool and found your tips very helpful. Many thanks.
@truewordz777
@truewordz777 3 года назад
A much appreciated video. Thank you👍🏽
@hughdanaher2758
@hughdanaher2758 4 года назад
Had to cut off the bottom of a pocket door so that it would clear a newly tiled floor. Usually you'd pull off the casing and other trim to remove the door, cut it with a circular saw and reset it. We used a multitool, wood spacer and careful cutting to do the job.
@milicentart
@milicentart 3 года назад
Love the tips, thank you!
@christopheroliveriii3985
@christopheroliveriii3985 3 года назад
Well done, awesome tutorial. Thank you sir.
@kmalik4221
@kmalik4221 4 года назад
Well done. Very impressed by your experience.
@Jeremy64444
@Jeremy64444 3 года назад
Just to say thanks. I had a very awkward job, where the bottom of an old door was catching a new carpet. I didn't want to remove hinges , because the screws would probably not grip, when refastened. I practiced your tips on old timber first and then did the job, came out perfect and saved me from dealing with a future sagging door. The tool I used was Erbaur 300watt corded. I choose this over battery, because I will probably use it , three or four times a year and the battery will just die, sitting unused. Thanks, you saved me a fortune..
@enduringcharm
@enduringcharm 3 года назад
That's great--glad to hear it!
@the250mikec
@the250mikec 3 года назад
Right on! Thanks for the tips. 👍
@CarlGreen01
@CarlGreen01 3 месяца назад
This was such an informative video that I couldn’t just ‘like’ it ….. I have to comment and say thank you very much …..
@rico1319
@rico1319 4 года назад
Really helpful video and nicely articulated! Thank you so much!! 👍👍👍😎🇨🇱
@robertsneed7689
@robertsneed7689 3 года назад
This was an awesome video of how to use this tool you brought out the best of the tool by using it very slow and taking your time to make the cuts more neater I appreciate you sharing this video with all of us out here in RU-vid land. I look forward to seeing other videos that you put out past and present. 👍🏿👌🏿👊🏿
@enduringcharm
@enduringcharm 3 года назад
Glad you enjoyed it!
@oneanddonetzone3673
@oneanddonetzone3673 2 года назад
Thank you well done! I’ve been wanting one of These saws for a while You’ve just helped Dewalt sell a product lol thank you again for your time well done!
@mattwaters6987
@mattwaters6987 4 года назад
Thanks for the great tips!
@kathybeyer1924
@kathybeyer1924 3 года назад
Thank you so much. This was excellent. (Yup I'm a beginner)
@murphyr31
@murphyr31 Год назад
I’m in need of this particular tool, I’m going to purchase one of them tomorrow in fact and found your video to be a good introduction and quite informative. Thanks for taking the time to film this video, it has certainly been helpful to me.
@oleboy4332
@oleboy4332 3 месяца назад
Thanks, great video! Buying one of these soon
@JM-sz4oi
@JM-sz4oi 3 года назад
Nice video. I had to trim ceramic tile on a counter top to install a new stove. Straight piece of wood, double stick tape, for a nice straight cut, Bosch half-moon diamond blade, vacuum for the dust. Great result. In that exercise Bosch blade superior to two other brands.
@enduringcharm
@enduringcharm 3 года назад
That's a tricky cut! No going back if you screw up.
@TheUkvolky
@TheUkvolky 3 года назад
Very good tips which I will try out on my new Multitool. Thanks
Далее
НАШЛА У СЕСТРЫ СЕКРЕТИК
00:36
Просмотров 298 тыс.
Я ВЕРНУЛСЯ 🔴 | WICSUR #shorts
00:57
Просмотров 444 тыс.
5 More Awesome Oscillating Tool Tricks
14:11
Просмотров 560 тыс.
CLEVER things to do with an Oscillating Multi-Tool!
10:28
Tape Measure Tips and Tricks - What is that marking?
12:05
SHAME ON YOU DEWALT
31:07
Просмотров 3,4 млн
20 Oscillating Multi-Tool Tips for Beginners
10:43
Просмотров 1,5 млн
I Bought 1-Star Tools on Amazon
27:12
Просмотров 1,1 млн
28 ways to use a Multi Tool | Dewalt
10:10
Просмотров 759 тыс.
Отнимают ребенка ч.7
0:55
Просмотров 3,6 млн
ДОМИК ИЗ АРБУЗА #юмор #cat #топ
0:40