Overview of the Siemens SIPART PS2 

I would like to thank you for that film, it helped me a lot, that tip of potentiometer, it wasn't so much clear on the manual, and with your explaination it was so much easier. Thank you very much!!!

Extremely helpful video, thanks for sharing. 👍🏼🇺🇸

Thanks for the film, it helped me a lot

Thanks for the video! It help me a lot!

Thanks a lot! Very clear and straight to the point! Show de bola!

This solved my problem, thanks a million

Great presentation, keep it up.

Great explanation ! Thank you

Very Helpful Video. Thanks a lot sir

Nicely explained sir

very good explanation and cleared described.....thank you very very much.

Very good and helpful video thanks

very detailed video!

Very simple and nicely teach thanku

Good explanation....!

Thank you 🎉

Very good sir

Thank you

nice video sir

Super Demonstration Sir love you from karachi Pakistan.

Thanks a lot engineer

Excellent explanations, thank you.

Muito boa a explicação! Parabéns !!!

it here any version intrisically safe for ATEX Zone 0? (Eexia=?)

Thanks a lot

아주 자세히 설명을 잘하시네요...

Thank you very much sir.. very useful video for me..

If its part-turn and i want to adjust it fail to close instead of fail to open, how can i do it?

thanks Sir

Great Video. I am facing a problem regarding with my rotary actuator. The valve is opening and closing manually, but the potentiometer value doesn't change. Tried to do initialisation, confused with the parameters. So kindly post the parameters for a rotary actuator. Thanks in advance.

muito esclarecedor obrigado.

Hello Sir, Have a good day. I have recently facing problem in a newly buying Siemens PS2(2wire, 4-20ma, 2 wire, without HART) smart positioner connect with my existing Single acting, air to open linear actuator(pneumatic control valve) having 20mm stroke when I am going to newly calibation. During commissioning this new positioner with existing control valve/actuator in initial condition its display shows P 85 and NOINI mode, at that time when if i press (+) and (-) button then the actuator totally doesn’t not move.only small clicking sound hearing inside the positioner and little air Release from actuating pressure line(Y1) of positioner , however pneumatic(4kg air pressure) and electrical(4ma , 24VDc) connection is there. Interesting is if i place old existing positioner there then it easily move the actuator after pressing (+) and (- ) key in NOINI mode. Is there any problem of lever setting or restrictor setting there.i don’t change any restrictor setting in this newly buying positioner during commissioning there.i am confused if there any setting required in restrictor at positioner during newly commissioning? Anybody here who can advice me kindly please to fix this problem.

Our valve is roatary type and it is not responding at all in auto mode. Current input is ok. Also works in the auto mode. Can anyone some with a suggestion?? Can re-calibrarion fix the problem?

When I install the new positioner to double acting actuator it goes straight away 100% and I can't close and initialize..also the + and - not operating...can anyone give suggestions please

What does it means during calibration as you mention we need to rotate the potentio meter wheel. What is the reason if that potentiometer wheel is not turning? I am facing this issue hence asking. Your valuable inputs are really appriciated. TIA

thanks

Very helpful video. Only issue I am running into now is when its in auto and modulating, the positioner indicates on the LCD screen an oFL code and the number 127.9, I'm not sure to how to resolve this issue.

So nice of you sir for the information. recently I have calibrated the same positioner on our Siemens gas turbine. Due to the position deviation. After I have done the calibration now it’s working normal. My question is why it has position deviation? And also elaborate the the frequency of calibration.

Nice

hello, can u plz tell me the inner parts like i/p converter etc. of a ps2 smart positioner.. plz reply me

I e done everything, even reset the unit My unit keep actuating to the open position. How can I correct this.

What to do. 100% open in 19 ma current?????

Absolutely brilliant video, I have identified my problem , my actuator was starting at 100% and therefore could not do the auto initialise. Can anyone say how to reverse the 100 to 0% using parameters 7 and 38. rise and FALL. when you have done' rise' or'fall' to reverse the action do you just go back to idle or do you initialise again?

Hi, Thank you for this video. It will be helpful If you guide us on the following point. When we remove Fieldbus signal cable - all control valves goes to closed position (fail close). => which is OK. When we reconnect Fieldbus signal cable - some control valve stay in same closed position (=> which is OK) where as few control valves slowly moving to open position which is not correct (=> in this case positioner set point automatically change to 100% while connecting signal cable; set point is not coming from DCS). We check positioner setting in both cases and unable to identify the reason for different action.

How to repire relay for this positioner....?

what about the flow adjustment in positioner

How can we factory reset it ?? Kindly rep plz

difference between 2 port & 3 port seimens valve positioner

Dear sir, have a good day. Thanks for uploading such type of excellent video. i have recently facing problem in a a newly buying Siemens PS2 positioner connect with existing Single acting linear actuator , 20mm stroke.during comissioning this new control valve/actuator in initial condition its display shows P 85 and NOINI mode, at that time when i press + and - button the actuator totally not move.only small sound hearing inside the positioner and some air release backside of positioner , however pneumatic and electrical connection is ok.if i place old existing positioner there then it easily move the actuator after pressing + and - key in NOINI mode. Moreover when i go in Log 5 ,NOINITM mode 30% open the valve in both YEND1 and YEND2 once i press both + and - key.once i release button then actuator go to zero condition.it doesn't hold at all. If its abnormal what can i do.would you please advice me. if i press only either + or - button then actuator not move in YEND1 and YEND2 mode.but when i press both + and - button simultaneously then it open actuator only 30% but not hold at all then when press hand button its display range message. will you please advice me its normal or abnormal? Really i am facing a horrible condition for this positioner at my site and i am apologetically wish to get you kind advice please. Thanking You, Engr.Nizamul hoq. proprietor. United Mechatronics Engineers. Bangladesh. Email: united.mechatronics@gmail.com Mobile : 0088-01814792505 and 0088-01935675378(whatsapp) Skype: nizamul.hoq1

Can I skip the leak test?

Great video, but I have a problem today ....... all ok, just, it works invert. 20mA = closed - 4mA is open (ballvalve valve - 90°) ? Who can help me. Many Thanks :-)

mielleur explication

ABB ???

Sir, one quesition

Difficult. Need easy maintaining