Тёмный

PCV VALVE - You MUST Clean This! | Vios/Yaris 

VIOSIFIED Car DIY
Подписаться 8 тыс.
Просмотров 128 тыс.
50% 1

PCV VALVE - You MUST Clean This! | Vios/Yaris is a step-by-step guide on locating, removing, cleaning, and reinstalling the Positive Crankcase Ventilation or PCV Valve on Toyota Vios / Yaris.
The PCV is just a small valve but it plays a vital role in preventing the build up of extreme pressures inside the engine which can cause oil leaks, blow by, sludge formation, etc., if it is dirty or not functioning properly.
By venting the inevitable build up of gas pressure from the crankcase the PCV valve can preserve the integrity of the oil seals, the engine oil, the engine block and prevent a lot of problems from happening. This is why it is so important to keep the PCV valve functioning properly by keeping it clean.
Its exact location may differ but the same principles and procedure shown in this video apply to all engines with a Positive Crankcase Ventilation system.
To reiterate, a dirty or clogged PCV valve can cause a heap of problems to your engine which can cost a lot of money in repairs.
Problems such as blow-by, oil leaks, oil sludge build-up, vacuum leaks, rough idling, and accelerated engine wear, among other things, can be avoided by simply cleaning or replacing this important part. This tutorial demonstrates how to perform this necessary maintenance.
As always, please exercise caution and common sense when working on your car. Seek the help of a professional whenever necessary. This and all other videos produced and published by Viosified Car DIY are for educational and reference purposes only. Viosified Car DIY and/or its owner/s shall not be held liable for any injury, damage, or mistake that may result from the misuse of the information presented by Viosified Car DIY channel.
Recommended Tools/Products: amzn.to/3rGcBML
FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW
ANCEL OBD 2 Scanner: amzn.to/3JiCiZU
Fully Automatic Smart Battery Charger: amzn.to/3gCbKGP
Digital Tire Pressure Guage: amzn.to/3GKsmqe
BOSCH Wiper Blades: amzn.to/3uH8Qss
Bumper Retainer Clips: amzn.to/3LuuK88
Fully Synthetic Motor Oil: amzn.to/3szZjAF
Panel & Trim Removal Tool Set: amzn.to/34Sw9o8
1000 Amp 12volt Car Jump Starter Pack: amzn.to/3JiEsJ0
Phone Mount for Cars: amzn.to/33hwYXs
FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW
VACLIFE Tire Air Inflator/Compressor: amzn.to/3JnGpDQ
AT-205 Re-Seal Stops Leaks, 8 Ounce Bottle: amzn.to/3Lttu58
#PCVvalve

Авто/Мото

Опубликовано:

 

8 дек 2020

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 153   
@Viosified
@Viosified 2 года назад
Recommended Tools/Products: amzn.to/3rGcBML FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW ANCEL OBD 2 Scanner: amzn.to/3JiCiZU Fully Automatic Smart Battery Charger: amzn.to/3gCbKGP Digital Tire Pressure Guage: amzn.to/3GKsmqe BOSCH Wiper Blades: amzn.to/3uH8Qss Bumper Retainer Clips: amzn.to/3LuuK88 Fully Synthetic Motor Oil: amzn.to/3szZjAF Panel & Trim Removal Tool Set: amzn.to/34Sw9o8 1000 Amp 12volt Car Jump Starter Pack: amzn.to/3JiEsJ0 Phone Mount for Cars: amzn.to/33hwYXs FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW VACLIFE Tire Air Inflator/Compressor: amzn.to/3JnGpDQ AT-205 Re-Seal Stops Leaks, 8 Ounce Bottle: amzn.to/3Lttu58
@ginongpratitdya4431
@ginongpratitdya4431 Год назад
Very clear explanation, thank you
@Viosified
@Viosified Год назад
I appreciate it. Thanks for watching.
@dominicfong6341
@dominicfong6341 2 года назад
Thank you so very much for all the details dear VIOSIFIED Car DIY.
@Viosified
@Viosified 2 года назад
You're welcome. Have a great day! :)
@patrishateodoro6841
@patrishateodoro6841 3 года назад
Thank u. You got a new subscriber 👍
@Viosified
@Viosified 3 года назад
Salamat po.
@sampsonikenna7757
@sampsonikenna7757 Год назад
Thanks you and a new subscriber.
@Viosified
@Viosified Год назад
Thanks! :)
@harem5178
@harem5178 2 года назад
Thank you !!
@Viosified
@Viosified 2 года назад
You're welcome :)
@zekareyasabeba5431
@zekareyasabeba5431 2 года назад
It is really good, and thanks
@Viosified
@Viosified 2 года назад
Thanks for watching 😊
@lincolnsanchez7960
@lincolnsanchez7960 3 года назад
Thanks for this video i like ur tutorial abt vios il try to do it by my self.
@Viosified
@Viosified 3 года назад
Welcome sir. Thanks for visiting VIOSIFIED. Good luck on your DIY 😊
@stayopenminded486
@stayopenminded486 Год назад
Great video.very we'll explained,Thank you.
@Viosified
@Viosified Год назад
Thanks for watching
@boathemian7694
@boathemian7694 3 месяца назад
Great video.
@Viosified
@Viosified 3 месяца назад
Thanks!
@djokojoedomiatmo7828
@djokojoedomiatmo7828 2 года назад
Subscribed... Thanks.
@Viosified
@Viosified 2 года назад
Thank you! 😊
@rodneyaquino3456
@rodneyaquino3456 3 года назад
Thanks boss a lot of learning that is very useful and save money for the labor. Mabuhay!
@Viosified
@Viosified 3 года назад
You're welcome sir. Thanks for watching. Please subscribe to VIOSIFIED for more tutorials. Keep safe :)
@infernus8926
@infernus8926 4 месяца назад
3:36 that bark sounded so realistic i thought it was my dog.
@Viosified
@Viosified 4 месяца назад
You have good speakers ☺️ Thanks for watching.
@henrichkeli1831
@henrichkeli1831 4 месяца назад
The 2013 yaris model is NCP92L-BEMR
@franciscojrliwanag8260
@franciscojrliwanag8260 2 года назад
Napaka simple unawain more to cone paps... Laking bagay kahit mejo nakakatakot gawin 🤣💪🤘💯
@Viosified
@Viosified 2 года назад
Salamat sir 😊
@xtdcxdoom7
@xtdcxdoom7 Год назад
Be sure car is cold before removing this type of pcv valve. Wear gloves when using carb cleaner. DON'T use carb cleaner if pcv valve is plastic use brake cleaner instead. If it rattles chances are it's working but to be sure use a balloon on the end of the hose it is connected and blow air. If the ball on stays inflated and no air is lost u can be sure it's working without leaks. Thanks for the video.
@Viosified
@Viosified Год назад
Thanks for watching
@gamingwitchutuu429
@gamingwitchutuu429 Год назад
Hay! The tube next to it connected to air intake mins have a crack an owner before me tried to put black tape but it’s off , do you think this the cause of my po171 code
@xtdcxdoom7
@xtdcxdoom7 Год назад
@@gamingwitchutuu429 P0171 can be a lot of things. Start by replacing pcv valve since it's so cheap
@gamingwitchutuu429
@gamingwitchutuu429 Год назад
@@xtdcxdoom7 ok 👍🏾
@nevinkuser9892
@nevinkuser9892 7 месяцев назад
​@@gamingwitchutuu429yes
@josephbingham1255
@josephbingham1255 26 дней назад
The second video I have seen where toxic brake fluid is soaking into skin. The Balloon test on another video is a good way to check performance.
@Viosified
@Viosified 25 дней назад
I appreciate your feedback. Thanks for watching!
@ayiepariff653
@ayiepariff653 2 года назад
Nk tnye knp kereta kalau nk speed tu tiba2 mcm semput sikit baru pegi . Tpi xselalu kadang2 jee.. nk kne tukar plug atau servis throttle body? vios ncp93
@jayramirez5374
@jayramirez5374 3 года назад
New subscriber 👍👍👍Meron ka na video to clean throttle body 👍👍👍 thanks
@Viosified
@Viosified 3 года назад
Hi sir, eto po video link sa "Throttle Body Cleaning." ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MKt0zXopBrM.html
@leonalvarez8269
@leonalvarez8269 Год назад
thumbs up
@hendridoni
@hendridoni 6 месяцев назад
Hello viosified. Greetings from Jakarta.
@Viosified
@Viosified 6 месяцев назад
Hi Hendri. Greetings from the Philippines 🇵🇭
@troysantos352
@troysantos352 3 года назад
Sir thank you very much i learn a lot from your video and the caption are very clear and valuable info. Can you please show us how to remove and clean oxygen sensor. Than you very much. Keep safe.
@Viosified
@Viosified 3 года назад
Will do sir, when time permits. :) Thank you so much for watching and for your positive feedback. God bless & keep safe!
@dfls5069
@dfls5069 2 года назад
@@Viosified How much pounds foot do you torque the PCV valve ? I installed one on a 2008 Yaris. I torqued to about three exposed threads, showing on the PCV valve. Same as previous PCV valve. It had about 3 threads exposed. You can easily strip the threads or over torque the housing is aluminum on the PCV valve.
@Viosified
@Viosified 2 года назад
@@dfls5069yes, I agree. I only torque the valve up to a point where it is snug enough to maintain seal and not more (maybe about 3 - 4 threads), because the valve is tapered and over-torquing could damage the engine block as you have pointed out.
@dfls5069
@dfls5069 2 года назад
@@Viosified Anything greater than 3 threads exposed on the PCV valve for the Toyota Yaris, you risk serious damage to the threads. I saw it with my own eyes. An amateur can easily destroy those threads. I should have left 4 threads exposed for the longevity of the threads. But 150 000 KM's and the PCV valve was in excellent shape.
@Viosified
@Viosified 2 года назад
Yup, totally agree. Good thing the pcv valve toyota uses is durable & easy to maintain.
@DougHinVA
@DougHinVA Год назад
easy to clean , but cheap to buy and install/remove. For $10-13 you can get a new one and keep the old one for an emergency...
@chingo3387
@chingo3387 11 месяцев назад
what is the part number for it?
@nanmatt2944
@nanmatt2944 2 года назад
Thanks sir.
@Viosified
@Viosified 2 года назад
You're welcome sir.
@carlmanalac1620
@carlmanalac1620 2 года назад
Hi, thanks for the video, can we use WD40 for the cleaning.
@Viosified
@Viosified 2 года назад
Hi. Please use Carburetor Cleaner for best results. :)
@sebastiaodosreiscarvalhoti2872
@sebastiaodosreiscarvalhoti2872 2 года назад
Ele limpou ela sem testar se ela estava boa,tinha que ter feito o teste da bexiga.
@Viosified
@Viosified 2 года назад
Não há nada de errado com o motor. Esta é apenas uma medida preventiva para evitar problemas futuros decorrentes da pressão excessiva do cárter devido a uma válvula PCV entupida. Obrigada.
@danarsaeed637
@danarsaeed637 Год назад
Hi there! Could ya please make a video removing and cleaning the intake manifold?
@Viosified
@Viosified Год назад
Ok, as soon as I get the chance :)
@fiphudoo
@fiphudoo Год назад
Why is it important to leave a gap between engine and pic valve?
@Viosified
@Viosified Год назад
Because the body of the PCV valve is tapered to form a seal. Forcing it all the way in could ruin the threads or cause stress cracks.
@leonrose7799
@leonrose7799 Год назад
Hi I have a 2010 1.3L toyota yaris idling is sometimes 600-700 rpm please help.
@Viosified
@Viosified Год назад
600 -700 idle rpm is within normal range.
@mcflurry7479
@mcflurry7479 Месяц назад
i should of watched your video first. I tightened the pcv valve ultra tight. But it still has the gap as you mentioned. Should I untighten it then tighten again?
@Viosified
@Viosified Месяц назад
If your pcv valve is tapered like the one in my video it doesn't have to be too tight. It just needs to be snug enough to create a seal & prevent a vacuum leak or unmetered air from entering the engine. If you think you over tightened it, you can loosen it a little until the tightness is "just right." (Do it while the engine is cool so you won't damage the threads) I hope this helps.
@mcflurry7479
@mcflurry7479 Месяц назад
@@Viosified thank you very much for your help. Unfortenaly i watched a similar video before i found yours, and he wasn't this informational about it. It helped a lot, but i wish i would have watched your first. I ended up tightening it it real tight. I tried to loosen it today but it wasn't giving. So i'll leave it as is. It didn't give me trouble when i went for a long drive today, so i will change it in another 60k miles. Thanks for your help once again!
@Viosified
@Viosified Месяц назад
@@mcflurry7479 you're welcome & thanks for the feedback. I appreciate you dropping by. Have a great rest of your day! 😊
@mohamadnazri7307
@mohamadnazri7307 3 года назад
Can use throttle body oil?
@Viosified
@Viosified 3 года назад
Use throttle body cleaner or carburetor cleaner for PCV valve. Any brand will do. Do not use oil, though :)
@Seraphim401
@Seraphim401 Год назад
What is the reason for the gap? My 1nzfe engine does not have the gap.
@Viosified
@Viosified Год назад
Some PCV valves (like the one in the video) have a tapered body to help form a seal to the engine block. Leaving a gap between the block and the valve as shown in the video helps to prevent over torquing it.
@faezalaziz932
@faezalaziz932 2 года назад
can i use throttle body cleaner?
@Viosified
@Viosified 2 года назад
Yes.
@jerryching6858
@jerryching6858 3 года назад
Sana meron ka na din change belt including diagram belt route along the rollers/pulleys
@Viosified
@Viosified 3 года назад
Hi sir, here's the link to belt replacement tutorial :) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-qKJQQJYVfZs.html
@pinoyako1927
@pinoyako1927 2 года назад
Can we use throttle body cleaner?
@Viosified
@Viosified 2 года назад
Yes sir, throttle body cleaner is okay.
@SlikLizrd
@SlikLizrd 2 года назад
Although pro mechanics don't clean PCV Valves (throw them away), if you INSIST on wasting time and money, Carb Cleaner, or "Gumout" is right for the job.
@eliezercamilo3713
@eliezercamilo3713 6 месяцев назад
Seria bueno agregar teflon?
@Viosified
@Viosified 6 месяцев назад
Normalmente no es necesario agregar teflón, especialmente si la válvula PCV de tu automóvil tiene un cuerpo cónico similar al que se muestra en mi video, ya que la rosca cónica crea un sellado natural entre la válvula PCV y el cárter.
@ericjosephpantaleon3660
@ericjosephpantaleon3660 2 года назад
Can i use turbo cleaner
@Viosified
@Viosified 2 года назад
For the PCV valve, if that is all you have, yes. Just don't use it to clean the MAF sensor, though.
@somethingdifferent9387
@somethingdifferent9387 2 года назад
Can we use brake cleaner for this ? Thank you
@Viosified
@Viosified 2 года назад
For PCV valve, yes you may if that is all you have. Just don't use it on MAF sensor and other precision electronic components, though.
@SlikLizrd
@SlikLizrd 2 года назад
DO NOT use Brake Cleaner for cleaning the PCV Valve. The correct chemical for the job is Carburettor Cleaner, such as "Gumout". Pros don't waste time and money by cleaning PCV Valves -- they are thrown away.
@SlikLizrd
@SlikLizrd 2 года назад
@@Viosified The correct answer is: NO !! It is never proper to use the wrong stuff "if that's all you have" -- When laying out a job, you get what you NEED before you start work. Basic Mechanics 101.
@Viosified
@Viosified 2 года назад
@@SlikLizrd I appreciate your input. However, this PCV valve cleaning video demonstrates a process that is part of our regular MAINTENANCE procedure as a PREVENTIVE MEASURE to keep the PCV valve in good shape. Note that it is NOT broken or defective, and thus only requires basic cleaning (NOT REPLACEMENT). If, on the other hand, the PCV valve reaches the end of its service life then we replace it as necessary. In our part of the world, money is tight and we do what we can to save it, if possible and within reason. Also, the PCV valve used in the video is entirely made of metal with NO sensitive electrical components or plastic that could be damaged by using brake cleaner. Therefore, it is not necessarily "the wrong stuff" to use. I did add a precaution to my reply to his question NOT to use brake cleaners on MAF sensors and other electronic components to avoid damaging them, as you may have read in my answer to that question. If you watched the video, you will see that I used carburetor cleaner for the PCV valve. Please note that this is a DIY channel aimed at helping non-pros who want to save some money by maintaining their cars at home using basic tools at their disposal. It includes precautionary advise as needed. The PCV valve in this case won't melt, explode, or break down if cleaned using a brake cleaner, hence the phrase: "if that is all you have. ' I then added a precaution not to use it on MAF sensors and other electronic components. (My exact words: "For PCV valve, yes you may if that is all you have. Just don't use it on MAF sensor and other precision electronic components, though.") Thank you for your feedback, Chuck. Have a good one!
@SlikLizrd
@SlikLizrd 2 года назад
@UCaU5_eA8Ln2PcSQFhQDVV0w Good morning to you, sir ! It's all good. You don't owe me any explanation. Sorry that you took a fence to my advice on saving time and money by NOT cleaning a PCV Valve. Funny how such a simple piece of common sense can be rejected out-of-hand, but hey, it's U-Tube, and it takes all kinds. Good luck to you, sir -- you're gonna need it.
@hushtdt
@hushtdt Год назад
If the rubber hose damage what happened
@Viosified
@Viosified Год назад
Damage (cracks, holes) to the pcv hose may cause vacuum leak issues
@sonygoup
@sonygoup Год назад
Man shit did not screw in that easy but it's the correct part number
@user-ts7gr8vq6p
@user-ts7gr8vq6p Год назад
What about Toyota Camry? It’s 3 hours of work in shop to change this valve. It’s located on crankcase…
@Viosified
@Viosified Год назад
The PCV (Positive Crankcase Ventilation) valve is always attached to the crankcase to do its job of releasing engine pressure, though its location and accessibility may vary depending on the type/model of the vehicle.
@tumab4u
@tumab4u 7 месяцев назад
My pcv valve hose is oily does this mean my pvc valve is bad?
@Viosified
@Viosified 7 месяцев назад
Yes, it could be clogged or stuck open especially if there's excessive oil. In either case you should clean - or, better yet - replace it. Check the hose for obstruction and damage and replace it if necessary. Check for signs of blow-by such as leaky engine gaskets or seals or visible smoke coming out of the dip stick tube while the engine is running. If you suspect excessive blow-by, you may want to have the engine's compression checked by a mechanic. Also, make sure the engine oil level is not excessive.
@beaharpst
@beaharpst 2 года назад
sir everytime po ba na magtatangal ng battery need mag idle relearn reset ECU?
@Viosified
@Viosified 2 года назад
Hindi na po ma'am. Pag lang po may issues sa makina o kaya matapos maglinis ng throttle body at laging mataas o erratic ang RPM, etc., dun lang po ginagawa yung basic ECU relearning. Pero kung nag disconnect o nagpalit lang ng battery hindi na po kailangan mag reset ng ECU. Salamat po.
@srmmotors07
@srmmotors07 Год назад
Whats the problems of this coad..
@Viosified
@Viosified Год назад
Can you clarify your question, please?
@m.naufalnurf_nfsr47
@m.naufalnurf_nfsr47 Год назад
Any When should I clean this? Every 10.000 Km??
@Viosified
@Viosified Год назад
I inspect and/or clean it every 20,000 km.
@henrichkeli1831
@henrichkeli1831 4 месяца назад
How much torque for thr pcv valve?
@Viosified
@Viosified 4 месяца назад
The specific torque recommendation for the PCV valve on a vehicle may vary, and it's best to consult the manufacturer's recommendation for your particular car model for precise information. However, if you're looking for a general guideline or common industry standard torque for PCV valves when specific manufacturer recommendations are not available, a torque of around 8 to 10 foot-pounds (ft-lbs) is often used for many automotive applications. Keep in mind that this is a general guideline and may not be applicable in all vehicles. If you're uncertain or unable to find the specific torque for your particular car model, tightening the PCV valve snugly by hand (as demoed in my video) without over-tightening is usually sufficient to ensure a proper seal without damaging the threads.
@henrichkeli1831
@henrichkeli1831 4 месяца назад
The 2013 yaris model is NCP92L-BEMR
@papap3814
@papap3814 2 года назад
Paps every kelan need maglinis pcv valve?
@Viosified
@Viosified 2 года назад
Pwede po linisin every 30k to 40k kilometers
@williampaglinawan5922
@williampaglinawan5922 3 года назад
Sir anong reason bakit kelangan tanggalin pa yung negative terminal sa battery wala naman tinanggal na socket dyan?
@Viosified
@Viosified 3 года назад
Extra precaution lang po yun para maiwasan ang electrical short circuit in case mapadikit sa positive terminal ng battery ang tool habang may ginagawa tayo sa engine bay. Energised po kasi ng negative current ang buong body at makina ng sasakyan kaya po mas mainam na idisconnect natin yung negative cable ng battery for safety.
@SlikLizrd
@SlikLizrd 2 года назад
Many engine manufacturers give instructions to remove the NEGATIVE battery cable before doing ANY work under the hood (bonnet) -- the reason being that doing so will PREVENT ACCIDENTAL DAMAGE to the electricl system, especially the on-board computer systems that work on very low voltage -- if 12 volts gets to the computer, it's a goner !! ALL-WAYS remove that NEGATIVE cable before working under the hood (bonnet).
@diomedesdelrosario7411
@diomedesdelrosario7411 2 года назад
Boss tama ba yung valve cover gasket ay lagyan ng silicon gasket paikot? Thank you boss
@Viosified
@Viosified 2 года назад
Kung tamang klase po ng rubber valve cover gasket ang ilalagay (at walang imperfections) hindi na po sya required lagyan ng silicon sealant paikot dahil "dry sealing" na po ang rubber gaskets pag hinigpitan sa tamang torque specs ang mga bolts ng valve cover. Salamat din po.
@diomedesdelrosario7411
@diomedesdelrosario7411 2 года назад
@@Viosified ohhh ganun pala, thank you boss
@Viosified
@Viosified 2 года назад
@@diomedesdelrosario7411 welcome po
@kevinl.sparks5066
@kevinl.sparks5066 Год назад
Dude the music is just too loud. Some voice commentary would be in order too
@user-xp9wk3rf9f
@user-xp9wk3rf9f 5 месяцев назад
Turn the sound off it has subtitles Bruv
@MansorMohdNoor
@MansorMohdNoor Год назад
may be I must service this item also... now my vios can't start with 1 kick
@Viosified
@Viosified Год назад
If the battery is strong enough to crank the starter motor, hard starting could be caused by several factors. A few things that come to mind is a dirty fuel filter, or a problematic fuel pump or fuel pressure regulator. Best option is to visit a good mechanic in your area for proper diagnosis.
@hanzjeremyjutic671
@hanzjeremyjutic671 Год назад
after cleaning, tumaas po ang minor.. ano po ggwin idol?
@Viosified
@Viosified Год назад
Kung erratic po ang minor, pwede nyo po ireset ang ecu. Pero iobserve nyo din po muna kung kusa syang babalik sa dati pag laon. Kung hindi pa rin, tsaka nyo po subukan ito: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3vixDnKlDhU.html
@eddomingo5011
@eddomingo5011 3 года назад
Gandang gabi bossing may garage po ba kayo para mapacheck ko vios ko po?
@Viosified
@Viosified 3 года назад
Hi sir, video tutorials lang po sa ngayon wala po ako shop. Thank you for watching.
@Teogaming2013
@Teogaming2013 3 года назад
@@Viosified loc nio po sir?
@Viosified
@Viosified 3 года назад
Laguna po
@Teogaming2013
@Teogaming2013 3 года назад
@@Viosified boss san po kau sa laguna?
@Teogaming2013
@Teogaming2013 3 года назад
@@Viosified taga laguna din po ako. Pde ko po kau puntahan para magpatulong sa vios ko?
@weishen5938
@weishen5938 2 месяца назад
Wot different then?
@Viosified
@Viosified 2 месяца назад
Engine performance & longevity
@zohaibkhan5069
@zohaibkhan5069 Год назад
Hey... Love your video.... Why did you changed pcv valve?
@Viosified
@Viosified Год назад
I just cleaned the PCV valve as preventive maintenance, I did not change it. Thanks for watching.
@sarfarazmalik8320
@sarfarazmalik8320 5 месяцев назад
Music makes difficult to follow it
@Viosified
@Viosified 5 месяцев назад
You can turn down the volume and just read the on-screen instructions. Thanks for watching.
@marlonsantos2356
@marlonsantos2356 2 года назад
sir pwede po makuha name mo aa mesenger
@Viosified
@Viosified 2 года назад
Same as the channel name po sir
@chuckwalla2967
@chuckwalla2967 Год назад
You over tightened the crap out of it.
@Viosified
@Viosified Год назад
Nope. I did not. If you watch the video again at 4:46 you'll see in the subtitle that I specifically cautioned against over-tightening it, that's why I explained the importance of leaving a gap between the engine block and the neck of the PCV valve (see 5:05). I knew where to stop because I was the one turning the wrench and I can FEEL how much resistance there was. Thanks for watching.
@dooflydetailguuy4349
@dooflydetailguuy4349 Год назад
​@@ViosifiedChuck felt with his eyes
@Viosified
@Viosified Год назад
@@dooflydetailguuy4349 lol 😂
Далее
bad pcv valve symptoms
6:14
Просмотров 152 тыс.
Toyota EGR Diagnosis Tips and Repair Tips
25:45
Просмотров 367 тыс.
ECU RESET | Vios / Yaris
7:18
Просмотров 136 тыс.
PCV VALVE CLEANING , TOYOTA YARIS WITH 1NR-FE ENGINE
5:40
Top 11 Symptoms of Bad PCV Valve
6:24
Просмотров 464 тыс.
HOW TO TEST AND CLEAN PCV VALVE ON CAR  EASY
8:51
Просмотров 119 тыс.
Trafik Işığını Yönetmek #shorts
0:18
Просмотров 12 млн