Тёмный

ECU RESET | Vios / Yaris 

VIOSIFIED Car DIY
Подписаться 8 тыс.
Просмотров 138 тыс.
50% 1

ECU RESET | Vios / Yaris is a simple how-to video about resetting Toyota Vios' ECU with manual transmission after a maintenance procedure has been done, such as throttle body cleaning, or when the idling or RPM becomes erratic for whatever reason.
The procedure shown in this tutorial is just another option you can try to "refresh" your car's ECU. It is always recommended to use an OBD 2 scanner if available for a more comprehensive diagnosis.
Different factors can cause issues in your car and sometimes a simple reset can fix minor problems.
If you don't have an OBD 2 scanner, you can try this to see if it fixes the issue.
NOTE: Usually issues can be resolved by just performing "STEP 1." In cases where "Step 1" did not help, repeat "Step 1" but this time proceed to "STEP 2" and see if it resolves the problem.
If your car has an automatic transmission, you can still use STEP 1 (which is disconnecting the battery cables and touching them together for 10 minutes) to refresh the ECU, but instead of proceeding to STEP 2 as described in this video, you can drive around at different speeds (slow to fast) with A/C "on" to help the ECU relearn the various shift points of the automatic transmission. The car may run a little rough while the ECU is relearning but continue driving around for a few kilometers and the car will eventually run better once the relearning process is completed.
If these steps doesn't help your car's problems, consult a mechanic and ask him perform a thorough diagnostics with an OBD 2 scanner.
As always, please exercise caution and common sense when working on your car. Seek the help of a professional whenever necessary. This and all other videos produced and published by Viosified Car DIY are for educational and reference purposes only. Viosified Car DIY and/or its owner/s shall not be held liable for any injury, damage, or mistake that may result from the misuse of the information presented by Viosified Car DIY channel.
Recommended Tools/Products: amzn.to/3rGcBML
FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW
ANCEL OBD 2 Scanner: amzn.to/3JiCiZU
Fully Automatic Smart Battery Charger: amzn.to/3gCbKGP
Digital Tire Pressure Guage: amzn.to/3GKsmqe
BOSCH Wiper Blades: amzn.to/3uH8Qss
Bumper Retainer Clips: amzn.to/3LuuK88
Fully Synthetic Motor Oil: amzn.to/3szZjAF
Panel & Trim Removal Tool Set: amzn.to/34Sw9o8
1000 Amp 12volt Car Jump Starter Pack: amzn.to/3JiEsJ0
Phone Mount for Cars: amzn.to/33hwYXs
FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW
VACLIFE Tire Air Inflator/Compressor: amzn.to/3JnGpDQ
AT-205 Re-Seal Stops Leaks, 8 Ounce Bottle: amzn.to/3Lttu58
#ECUReset
ANCEL OBD 2 Scanner: amzn.to/3JiCiZU
Battery Charger: amzn.to/3gCbKGP

Авто/Мото

Опубликовано:

 

27 июн 2021

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 411   
@Viosified
@Viosified 2 года назад
Recommended Tools/Products: amzn.to/3rGcBML FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW ANCEL OBD 2 Scanner: amzn.to/3JiCiZU Fully Automatic Smart Battery Charger: amzn.to/3gCbKGP Digital Tire Pressure Guage: amzn.to/3GKsmqe BOSCH Wiper Blades: amzn.to/3uH8Qss Bumper Retainer Clips: amzn.to/3LuuK88 Fully Synthetic Motor Oil: amzn.to/3szZjAF Panel & Trim Removal Tool Set: amzn.to/34Sw9o8 1000 Amp 12volt Car Jump Starter Pack: amzn.to/3JiEsJ0 Phone Mount for Cars: amzn.to/33hwYXs FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW VACLIFE Tire Air Inflator/Compressor: amzn.to/3JnGpDQ AT-205 Re-Seal Stops Leaks, 8 Ounce Bottle: amzn.to/3Lttu58
@zheyespinosa8031
@zheyespinosa8031 2 года назад
Worked perfectly for my VIOS XLE CVT 2021! Thank you boss!
@Viosified
@Viosified 2 года назад
I'm glad the video was helpful. Thanks for the feedback :)
@kristofferocampo8588
@kristofferocampo8588 8 месяцев назад
Hello sir paanong procedure po ginawa nyo sa vios xle cvt 2021 model nyo? Salamat
@jbell0124
@jbell0124 9 месяцев назад
Boss sobrang nakatulong video mo pagreset ng ecu, nareset ko din sa pagkatriggered yung anti-theft alarm ko
@amaroyal96
@amaroyal96 Год назад
Omg cant believe it worked like a charm ♥️♥️
@yolanrodriguez876
@yolanrodriguez876 2 года назад
Thank you boss at madaling intindihin ang tutorial video mo.
@Viosified
@Viosified 2 года назад
Salamat din po sir
@marcdaryldano6936
@marcdaryldano6936 Год назад
Thank you so much!!!
@kurtromersondeguzman8625
@kurtromersondeguzman8625 2 года назад
Salamat po sa maliwanag at detalyadong pagshare
@Viosified
@Viosified 2 года назад
Welcome sir. Salamat din po :)
@julitovillasis9927
@julitovillasis9927 2 года назад
salamat sa pag share ng idea sir malaking tulong po ito sa akin
@Viosified
@Viosified 2 года назад
Welcome po sir. :)
@keng.48
@keng.48 2 года назад
watching all your vids. very informative,new subs here
@Viosified
@Viosified 2 года назад
Thank you for watching & subscribing, sir 😊
@keng.48
@keng.48 2 года назад
Maraming salamat din sayo Sir
@Viosified
@Viosified 2 года назад
@@keng.48 God bless you sir 🙏😊
@jayramirez5374
@jayramirez5374 3 года назад
Nice 👍one viosified, good job😊
@Viosified
@Viosified 3 года назад
Thank you sir :)
@ze.empire
@ze.empire Год назад
Salamat sa video mo ton, malaking tulong ito
@Viosified
@Viosified Год назад
Welcome sir
@waa_abdikarem
@waa_abdikarem 3 месяца назад
It worked perfectly, thank you very much.
@Viosified
@Viosified 3 месяца назад
You're welcome!
@batanghook5606
@batanghook5606 2 года назад
thanks sa info .keep it up
@Viosified
@Viosified 2 года назад
Thank you sir :)
@HakutenGaming
@HakutenGaming 2 года назад
done watching very informative thanks for sharing sir
@Viosified
@Viosified 2 года назад
Thanks for watching 😊
@marvelinoniem2557
@marvelinoniem2557 3 года назад
Thank you sir :)
@Viosified
@Viosified 3 года назад
You're welcome sir. Thank you for watching :)
@sarwarkulbari7667
@sarwarkulbari7667 Год назад
My toyota yaris wont go D and R i was changed the car also same problem ?
@reymundmacabenta1
@reymundmacabenta1 21 день назад
Salamat sir, although diko pa na try pero sa tingin ko gagana to. Lumakas kasi ang ang fuel consumption after ko ma linis ang throttle body, yung una kong ginawa linis ng spark plug at fuel injector , lumakas sa gas pero nag ok sya after ko patakbuhin ng 90 kph. Ngayon naulit na naman
@Viosified
@Viosified 21 день назад
@@reymundmacabenta1 welcome sir. Isama nyo na din po sa linis yung MAF sensor, madali lang linisin, meron din ako tutorial sa playlist kung kailangan nyo reference. Good luck po!
@duongkien4837
@duongkien4837 Год назад
many thanks bro
@Viosified
@Viosified Год назад
Thanks for watching :)
@user-cu1wj6rf5y
@user-cu1wj6rf5y 6 месяцев назад
Thank you
@lkthWhereWeBelong
@lkthWhereWeBelong Год назад
Great video, will this work on chr hybrid?
@mahmooudhusin7339
@mahmooudhusin7339 2 года назад
Hi I’m want help me for Toyota Camry 2020 I’m changing ECU engine how to reset computer ECU
@Viosified
@Viosified 2 года назад
Hi. If you are installing a new ECM/ECU you will need a scanner to write the VIN to the new ECM/ECU and you need to input the codes for the immobiliser, otherwise the car will not start.
@Viosified
@Viosified 2 года назад
For automatic cars, just perform STEP 1 for 10-15 minutes. Then, reconnect the battery and start the engine. Skip step 2. Let it idle until the RPM goes down to about 900 - 700 then turn on the A/C while idling for 5 minutes. After five minutes, drive around for at least 15 - 30 minutes with A/C "ON." Drive at varying speeds (slow to fast) to help the ECU relearn the shifting points. The initial run may be slightly rougher than usual, but it is to be expected during the relearning process. It will eventually stabilize as the ECU relearns the new parameters while you continue to use your car.
@dandeloria4797
@dandeloria4797 2 года назад
Question lang po, meron po bang video for automatic? Kasi ngayon ito po yung problem ko. Thank you po!
@Viosified
@Viosified 2 года назад
Hi sir. Wala po video pero same principle din po sila. Nakan pin po sa comments section yung mga steps for A/T cars :) Salamat po
@arthkerenceespanto6011
@arthkerenceespanto6011 2 года назад
Sir pati po sa gas consuption mag babago po sya? Kung na reset ang ecu. Vios xle at here
@Viosified
@Viosified 2 года назад
Nakakatulong po sya na ibalik sa default ecu parameters, lalo na po kung medyo lumalakas na fuel consumption ng sasakyan (pero marami pa pong ibang factors ang nakaka apekto sa fuel consumption).
@arthkerenceespanto6011
@arthkerenceespanto6011 2 года назад
@@Viosified thanks po. Yung instructions mo po sa pan automatic na procedure yun po yun?
@optimumpride7395
@optimumpride7395 3 месяца назад
It worked on my nissan sentra GX
@Viosified
@Viosified 3 месяца назад
I'm glad it worked. Thank you for the feedback.
@diyiertv4352
@diyiertv4352 3 года назад
new subscriber here.. more videos to watch please
@Viosified
@Viosified 3 года назад
Thank you for watching and subscribing sir. More tutorial videos to come.
@trannam8114
@trannam8114 3 года назад
Can You please make detailed instructions on how to replace the fuel filter in toyota vios/yaris cars? Thanks
@Viosified
@Viosified 3 года назад
Will do, as schedules permit :)
@kuyafrankiethetransporter7104
@kuyafrankiethetransporter7104 2 года назад
Thankx bro
@Viosified
@Viosified 2 года назад
Salamat din po :)
@muhdshahmin4537
@muhdshahmin4537 2 года назад
Can i know what spec bodykit vios first video..
@Viosified
@Viosified 2 года назад
Hi. If you're asking about the model, it is a 2015 Vios 1.3E M/T. I hope this answers your question. If not, please feel free to ask again. Thank you :)
@pnhpnh1202
@pnhpnh1202 Год назад
Good Video
@Viosified
@Viosified Год назад
Thank you
@mekteb.shemal
@mekteb.shemal 5 месяцев назад
VERY VERY GOODD APPPLAUSE
@emmanuel6797
@emmanuel6797 10 месяцев назад
Will it works for Chevrolet spark car sir
@Viosified
@Viosified 10 месяцев назад
Yes sir
@lesterjohnmatienzo2772
@lesterjohnmatienzo2772 Год назад
Nice video. Mlaki tulong at bagong kaalaman s vios owner. More power. Godbless. Ask ko lang po regarding s air cleaner hose? Mgkaiba po ang matic at manual?
@Viosified
@Viosified Год назад
Salamat po. Kung same engine type po, pareho lang po sa A/T at M/T.
@EdgardoRegalaOngsiakoJr.
@EdgardoRegalaOngsiakoJr. 4 месяца назад
Tnx sa info sir
@Viosified
@Viosified 4 месяца назад
Welcome po. 🙏🙂
@onegridmusic
@onegridmusic 8 месяцев назад
Where and how do you get your knowledge from doing this, did you do a research or study for it yourself or someone taught you? Pls don’t take this personally but i am curious on how by doing this steps will reset the ECU or “Relearn” the idle of an engine.
@Viosified
@Viosified 8 месяцев назад
I appreciate your question. First, you learn this by studying automotive mechanics; second, by doing your research; and third, through experience. To answer your other question, the ECU or ECM is designed to reset or refresh its memory when the power supply to it is interrupted. It is configured to store default parameters and delete adaptive memories as necessary, much like how you can erase or refresh your computer's Random Access Memory when you restart it. Similar to your computer's RAM, the ECU also stores (or relearns) new information as you use your vehicle. The ECU or ECM functions similarly to your computer's RAM by storing or learning new information about your driving habits, fuel trims, ignition timing, idle speed, etc. These are referred to as adaptive parameters, which the ECU stores as new memory as you drive your vehicle.
@yusufaras01
@yusufaras01 Месяц назад
What is the reference for this procedure?
@flax_droidgamer6979
@flax_droidgamer6979 2 года назад
Good day.. regarding s idling.. during traffic with stop and go situation rpm goes 500 and felt vibration but after a moderate traffic rpm is fine.. San po pde magsimula ng troubleahooting? Vios automatic...
@Viosified
@Viosified 2 года назад
Hi sir. You can start by observing if the RPM drop occurs during braking. If it does, it could be a sign of a developing vacuum leak in the brakes and/or brake booster system. Other things to consider are possible vacuum leaks in the intake hoses and EVAP system; condition of the MAF sensor, O2 sensors, throttle body; possible cyclinder misfires, condition of the sparkplugs/ignition coils, just to name a few. However, in order to minimize guesswork, it would be a good idea to obtain a comprehensive diagnostics with an OBD2 scanner to check the error history (if any) and performance of the engine, sensors, and ignition system, among other things. Please note, however, that occasional slight vibration is normal for in-line four cylinder engines due to the way mechanical balance is affected or distributed during the combustion cycle. Thank you. I hope this helps.
@mekteb.shemal
@mekteb.shemal 5 месяцев назад
THANKS PLEASE SHARE ALL WORK ON YARIS
@yusufaras9066
@yusufaras9066 Год назад
tried to corolla altis 2017, 1.33 VVT-i but didn't helped.
@Viosified
@Viosified Год назад
It is for Yaris/Vios model, done after throttle body cleaning to refresh ECU parameters. Thanks for watching.
@eironstech0610
@eironstech0610 Год назад
May mas mabilis na tarika jan bro.. peo ok ung ginawa mo..
@tanakdusunrock
@tanakdusunrock Год назад
Good info frnd
@Viosified
@Viosified Год назад
Thanks!
@royhernandez5629
@royhernandez5629 2 года назад
thank you Sir. more videos p po. GOD Bless...
@Viosified
@Viosified 2 года назад
Salamat po sir. :) More vids to come. God bless 🙏
@eldarjanelopezon180
@eldarjanelopezon180 2 года назад
Ty paps
@Viosified
@Viosified 2 года назад
Welcome po sir :)
@erostyler6226
@erostyler6226 3 года назад
Boss same method ba sa Innova 2013 gas? Inalis kc baterya ng matagal dahil nilinis engine bay.
@Viosified
@Viosified 3 года назад
Yes sir, kahit yung step 1 lang po pwede na kung inalis lang naman po ang battery.
@ginongpratitdya4431
@ginongpratitdya4431 Год назад
Is it work for Vios second generation 2007? Thanks
@Viosified
@Viosified Год назад
Yes
@ginongpratitdya4431
@ginongpratitdya4431 Год назад
@@Viosified thank you
@anicetonikkodeguzman2255
@anicetonikkodeguzman2255 2 года назад
Good day sir.. just did exactly what i watched on your video tutorial.. after po ng procedure pag ka start ko engine up and down po ung RPM until 5000rpm po sya nag steady… automatic toyota vios 2014 po car ko.
@Viosified
@Viosified 2 года назад
Ano ano po mga ginawa ninyo sa sasakyan, bakit po kayo nag reset? Nilinisan nyo po ba ang throttle body?
@anicetonikkodeguzman2255
@anicetonikkodeguzman2255 2 года назад
@@Viosified ngpalinis po ako ng entire fuel system ksma throttle body , ngtry ako ireset ecu then ngaun taas baba na po RPM nya pag nka idle lng.. pgopen AC tumataas rpm nya ng 7000rpm to 9000rpm..
@Viosified
@Viosified 2 года назад
@@anicetonikkodeguzman2255 nagrerelearn po ang ecu, pero masyado po mataas ang rpm kung umaabot ng 7000 rpm. Ang normal po ay 600 to 1000 rpm (from idle to AC clutch engagement). Naririnig nyo po ba na galit na galit o nag high rev makina? Normal po kasi na mag fluctuate pataas at pababa ang rpm tuwing nageengage at disengage ang AC clutch ng compressor, kaya ko po naitanong kung sobrang galit na galit po ang makina ng unit nyo
@anicetonikkodeguzman2255
@anicetonikkodeguzman2255 2 года назад
Sir i mean 700rpm to 900rpm po pag nka engage ang AC.. pero pag nka off AC nag fflactuate sya taas baba sya ung idle nya..
@Viosified
@Viosified 2 года назад
Ah, within normal range naman po sya kung ganun. Usually po medyo rough talaga idle during relearning process ng ecu pero bumabalik din sa normal pag ginamit nyo na ang sasakyan, after about 50 to 100 km (slow - fast - slow driving). Pag hindi pa rin po bumalik sa normal o kung masyadong malikot ang fluctuation at may unusual vibration ang makina maaring vacuum leak po ang dahilan or maduming MAF sensor. Ipa check nyo po dun sa gumawa.
@kristofferocampo8588
@kristofferocampo8588 8 месяцев назад
Hello po good day. Pwede po ba ito sa vios 2021 XLE cvt model?
@Viosified
@Viosified 8 месяцев назад
Pwede po
@arviegallardo7595
@arviegallardo7595 2 года назад
Sir ask ko lng anong gearl oil gmit mo sa transmission mo.slamt
@Viosified
@Viosified 2 года назад
Toyota Manual Transmission Gear Oil API: GL-4 SAE: 75W-90 po sir.
@rongabriel6004
@rongabriel6004 2 года назад
Pwede din po ba to sa vios 2017 double vvti?
@Viosified
@Viosified 2 года назад
Opo sir after throttle body cleaning
@ricdasalla4993
@ricdasalla4993 5 месяцев назад
Sir , pwede din ba sa Vios gen 1 automatic transmission 2007 model..thank you
@Viosified
@Viosified 5 месяцев назад
Pwede po
@abrahampoquita8416
@abrahampoquita8416 2 года назад
Ganyan din b pag ng palit ka ng air filter n simota? Vios gen 2
@Viosified
@Viosified 2 года назад
Pwede rin po
@kylevincentfrancisco7477
@kylevincentfrancisco7477 2 года назад
Boss after pressing the gas pedal, ibabalik pb sa off yung susi or deretso n start? Thanks po
@Viosified
@Viosified 2 года назад
Hanggang ACC lang po, hindi na sya io-OFF sir. Then from ACC derecho start na po. :)
@markdavedigno2972
@markdavedigno2972 2 года назад
GoodDay sir. What if nagpalit po kami ng open pipe sa vios tinanggal dn po ang Catalytic. Tapos nanawa na sa open pipe... Binalik na dn stock pipe and canister. Kelangan pa dn po ba ireset ang ecu? Salamat po
@Viosified
@Viosified 2 года назад
Hi sir. No need na po kung hindi naman umiilaw ang check engine light o kung wala naman naging problema, pero kung meron pong issues pwede nyo po subukan. In case hindi po kinaya ng simpleng reset, pwede nyo po gamitan ng OBD 2 scanner para idelete ang errors at macheck na din ang status ng mga sensors at ng makina. Salamat po.
@user-nf1lv6lf1k
@user-nf1lv6lf1k 10 месяцев назад
i think it is better to reconnect the negative terminal on the battery first
@Viosified
@Viosified 10 месяцев назад
The reason for connecting the positive cable first is to ensure that any accidental contact between the positive cable and the metal parts of the car does not create sparks. Sparks near the battery can be dangerous, as the chemical reactions inside the battery produces flammable gases (specifically hydrogen & oxygen) that can be ignited by sparks. By connecting the positive cable first, you reduce the chances of sparking near the battery.
@ronolivar1039
@ronolivar1039 8 месяцев назад
Sir pwede rin po ba to sa bagong palit na engine?lost communication din kasi pag pina scan ko.thanks
@Viosified
@Viosified 8 месяцев назад
Pwede nyo po subukan, pero kung may problema sa wiring o fuse, o incompatibility sa firmware o protocol ng OBD2 scanner at on-board computer ng makina, hindi po sya uubra. Icheck nyo din po kung tugma yung connector ng scanner, at yung power level ng battery, at kung ok ang grounding.
@vincabingabang4696
@vincabingabang4696 2 года назад
Sir yung vios 2018 ko minsan humuhina kuryente at low power kahit tumatakbo.humihina at nagbliblink yung ilaw ng dash board may dash board.
@Viosified
@Viosified 2 года назад
Sir, ipacheck nyo po kondisyon ng BATTERY (baka mahina o palitin na), BATTERY CABLES (kung may damage) & BATT CABLE CONTACTS (for loose connection), at ALTERNATOR (kung sapat ang supply ng kuryente). Isama nyo na din po ang DRIVE BELT (belt tension baka maluwag o dumudulas).
@user-pw6hy4rg5z
@user-pw6hy4rg5z 2 года назад
hi po sinundan ko po yung instruction nyo pero hindi po na reset yung ecu MT Vios 2016. issue ng vios ko po is bumaba ang rpm ng 500-450. tinanggal ko po kasi ang battery ng 1day dahil sa alarm. pwede ko po kaya ulitin yun since na start ko na ang engine? nag rerelearn po ba kusa sa katagalan? thanks po
@Viosified
@Viosified 2 года назад
Kung 1 day disconnected sa battery malamang po nag reset na sya, hayaan nyo na lang po mag relearn ang ECU. Idrive nyo na lang normally gaya ng dati. Unti unti po magre-relearn ang ECU habang dinadrive ang sasakyan (for about 50km to 100km). Yung steps po sa video ay para lang ma-facilitate ang relearning process pero kahit hindi nyo na ulitin yun. Salamat po.
@albertespiritujr8896
@albertespiritujr8896 2 года назад
Ganyan nangyari sakin pwede poba sa yaris 2011 para lagi galit yung makina pag umaandar
@Viosified
@Viosified 2 года назад
Pwede nyo po sya subukan sir. Kung sakali hindi pa rin makuha ng basic reset, ipa scan nyo po gamit ang OBD2 scanner para malaman kung may mas malalim na dahilan ang surging ng makina.
@theheavenheaven
@theheavenheaven 2 месяца назад
Sir pag walang hatak anh kotse palit coil na at linis n din ang fuel injector at linis n dn ang carb pero gnun p dn
@Viosified
@Viosified 2 месяца назад
Ibaiba po kasi ang pwede maging sanhi nyan, pwede din po low compression, o maduming mga sensors, baradong fuel filter, intake at exhaust systems, clutch engagement issues, etc, etc.. Mas mapapadali po ang diagnosis kung mapa tingnan nyo sa mekaniko na may OBD2 scanner para mapinpoint po ang sanhi
@chardjapanvlog2940
@chardjapanvlog2940 Год назад
Boss pwedi po bayan kahit anong mn sasakyan gagamit pag resit ECU
@Viosified
@Viosified Год назад
Hindi po sir
@izzaqelanaqimohammadhafiza2610
@izzaqelanaqimohammadhafiza2610 11 месяцев назад
How about ncp150 push start button bro
@Viosified
@Viosified 11 месяцев назад
For automatic cars, just perform STEP 1 for 10-15 minutes. Then, reconnect the battery and start the engine. Skip step 2. Let it idle until the RPM goes down to about 900 - 700 then turn on the A/C while idling for 5 minutes. After five minutes, drive around for at least 15 - 30 minutes with A/C "ON." Drive at varying speeds (slow to fast) to help the ECU relearn the shifting points. The initial run may be slightly rougher than usual, but it is to be expected during the relearning process. It will eventually stabilize as the ECU relearns the new parameters while you continue to use your car.
@izzaqelanaqimohammadhafiza2610
@izzaqelanaqimohammadhafiza2610 11 месяцев назад
Thnks bro. Give u subsribe
@Viosified
@Viosified 11 месяцев назад
@@izzaqelanaqimohammadhafiza2610 Thank you! I appreciate it!
@chinitongcaviteno3118
@chinitongcaviteno3118 Год назад
Sir kapag nag reset ako ng ECU marerelearn niya yun old rpm bago ako mag reset o irerecord niya yun latest driving habit mo?
@Viosified
@Viosified Год назад
Pag nag reset po kayo ng ecu buburahin nya po yung lumang parameters tapos ire-relearn po nya uli ang driving habits nyo
@marlonsantos2356
@marlonsantos2356 2 года назад
sir pwede po ba yan sa vios gen2 matic
@Viosified
@Viosified 2 года назад
Yes sir. For automatic cars, just perform STEP 1 for 10-15 minutes. Next, reconnect the battery and start the engine. Let it idle until the RPM goes down to 700 - 900 then turn on the AC for about 5 minutes. After five minutes, drive around for at least 15 - 30 minutes with AC "ON" to allow the ECU to relearn the new parameters. The initial run may be a little rough and the idle a little lower than usual, but it is to be expected during the relearning process. It will eventually stabilize after driving the car around a few times or a few hundred kilometers. The ECU will continue to relearn as you continue to use the car. Thank you :)
@junjungebutan843
@junjungebutan843 9 месяцев назад
pwede po ba sa ibat ibang sasakyan yun pag reset na icoconect yung + - ng battery cable. vvti
@Viosified
@Viosified 9 месяцев назад
Pwede naman po. Ang limitations po ay dun sa mga high end na sasakyan na kailangan ng specific codes para mag reset.
@junjungebutan843
@junjungebutan843 9 месяцев назад
@@Viosified cge pod. salamat
@shahriarmohamadi6663
@shahriarmohamadi6663 2 месяца назад
what would happen if we didn't do it after cleaning the throttle body?
@Viosified
@Viosified 2 месяца назад
The engine may behave erratically if the old parameters are not deleted from the ecu memory.
@shahriarmohamadi6663
@shahriarmohamadi6663 2 месяца назад
@@Viosified I have a Yaris 1.0 it jerks when starting and also when releasing the throttle sometimes difficulty starting no faults no warning lights on every time I clean the throttle body it gets better but there is always the same problem
@Viosified
@Viosified 2 месяца назад
@@shahriarmohamadi6663have you tried cleaning the MAF sensor yet? if you haven't done so, here's a tutorial on how to do it: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-6xi5OLAuldA.htmlsi=ZumSS0eOuy56rXA_
@jovenbrothers4344
@jovenbrothers4344 2 года назад
Sir good day vios mt 2018, 1st gear po bumabagsak sa 5000 to 4000 rpm kaya namamatay po ang makina pag bagsak na sya.ano po ang pwedeng dahilan at paano po ito maayos
@Viosified
@Viosified 2 года назад
Good day sir. Iba iba po maaring dahilan. Makakatulong po kung mapa-scan muna ang Vios nyo gamit ang OBD2 scanner para ma rule-out po ang posibleng issues dulot ng faulty sensors, evap leak, lean air-fuel mixture, cylinder misfires, etc.., at para malaman din po ang error history at current condition ng makina. Salamat po.
@michaelsantos5591
@michaelsantos5591 Год назад
Good day sir!!! Ano poh kaya problema minsan nagloloko aapakan ko accelator ayaw humatak... pag binaon accelator delay ung hatak nia gang 40kms. Lang poh xa... toyota yaris 2015
@Viosified
@Viosified Год назад
Napa check nyo na po ba gamit ang OBD2 scanner? Madami po kasi pwedeng dahilan, kaya mas mabuti po kung ipa-scan para ma-pinpoint agad ang dahilan.
@alvintalag291
@alvintalag291 Год назад
S 4A-FE engine sir.. parehas lng b..
@Viosified
@Viosified Год назад
Opo sir
@elfelicianopablo6892
@elfelicianopablo6892 3 года назад
mahusay idol new subs po
@Viosified
@Viosified 3 года назад
Salamat po sir :)
@Jai-oc3xy
@Jai-oc3xy 2 года назад
Gagana din ba toh sa mga vios 2008?
@Viosified
@Viosified 2 года назад
Pwede po sir
@aldrinvillaluz3999
@aldrinvillaluz3999 9 месяцев назад
Boss tanung lqng ako paano kaya ung xle cvt n 2023 normal lng ba umaabot ung rpm nya n 2500 rpm meron siya bwelo pero na delayed siya klngan umabot ng ganun rpm n 2500 pag mga 100kph ka salamat anu kya problem
@Viosified
@Viosified 9 месяцев назад
Wala pong problema unit nyo kung umaabot ng 2500 ang rpm nya sa bilis na 100kph. May 'rubber band effect' po talaga ang CVT transmission kaya medyo may konting delay po sya kumpara sa manual transmission.
@aldrinvillaluz3999
@aldrinvillaluz3999 9 месяцев назад
@@Viosified salamat boss
@japhetcimanes6209
@japhetcimanes6209 2 года назад
Sir ung vios q 2017, minsan ang ganda ng pickup, minsan makunat, bakit poh sir ganon?
@Viosified
@Viosified 2 года назад
CVT po ba sir? Napalinis nyo na po throttle body?
@aldrinvillaluz3999
@aldrinvillaluz3999 9 месяцев назад
Na reset po ba rpm ng vios cvt
@Viosified
@Viosified 9 месяцев назад
Maraming factors po ang nagde-determine ng engine rpm (ex. throttle position, ecu programming, fuel injection, vehicle load, acceleration pedal input, ignition timing, etc), at depende po kung bakit nyo kailangan ireset.
@user-og5zz1mh6u
@user-og5zz1mh6u 10 месяцев назад
Sir paano po Yung sa vios ko tinaggal ko kasi ung MAF sensor habang umaandar and then bumaba po yung idle tapos mavibrate Sana mapansin salamat sa feedback
@Viosified
@Viosified 10 месяцев назад
i-off nyo po muna makina at ikabit nyo ulit yung MAF sensor. Kailangan po nakakabit ang MAF sensor kasi yun po ay isa sa nagreregulate ng tamang air-to-fuel ratio na kailangan ng makina. Mago-ON po ang Check Engine Light Pag pinaandar nyo makina na walang MAF sensor. Pag di po nag-OFF ang Check Engine Light pagkakabit ng MAF sensor, ireset nyo lang po ECU (kahit step 1 lang ang gawin nyo): ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3vixDnKlDhU.htmlsi=FGB6KSEQbTSF4V8x
@myrecipientad
@myrecipientad 2 года назад
Sir, mataas ang idle... IACV nalinis pa po ba?
@Viosified
@Viosified 2 года назад
May ginawa po ba kayo sa makina bago tumaas ang idle, sir? Kung naglinis po kayo ng throttle body ireset nyo po ang ECU para bumaba uli ang idle rpm.
@nathanielfuentes315
@nathanielfuentes315 3 года назад
Boss.i change battery only last march.need b reset o d n?salamt.
@Viosified
@Viosified 3 года назад
No need na po sir kung wala naman issues ang engine
@nathanielfuentes315
@nathanielfuentes315 3 года назад
@@Viosified salamt sa reply sir.more power.
@Viosified
@Viosified 3 года назад
Salamat po God bless
@brinxbrian9773
@brinxbrian9773 3 года назад
@@Viosified Sir pag tinanggal ko po ang neg.terminal
@brinxbrian9773
@brinxbrian9773 3 года назад
@@Viosified Sir pag tinanggal ko ang neg.terminal dahil 2 weeks na hindi ko magamit ang kotse kailangan ko ba i reset pag gamitin ko na?Salamat po.More power.
@sorillano
@sorillano 2 года назад
Sir, paano kapag nawala ung warning sounds (if naiwan mo nakaopen headlight then you turn off the car, and when you forgot to put searbelt on) paano mababalik/repair un? Salamats ng marami!
@Viosified
@Viosified 2 года назад
Bago po nawala warning sounds meron po ba kayo pinagalaw sa unit? May idinagdag po ba na accessories?
@jannerbugarin3009
@jannerbugarin3009 2 года назад
Same lang din po ba sa automatic?
@Viosified
@Viosified 2 года назад
Hi sir. For automatic cars, just perform STEP 1 for 10-15 minutes. Then, reconnect the battery and start the engine. Let it idle until the RPM goes down to about 900 - 700 then turn on the A/C while idling for 5 minutes. After five minutes, drive around for at least 15 - 30 minutes with A/C "ON." Drive at varying speeds (slow to fast) to help the ECU relearn the shifting points. The initial run may be slightly rougher than usual, but it is to be expected during the relearning process. It will eventually stabilize as the ECU relearns the new parameters while you continue to use your car.
@kylevincentfrancisco7477
@kylevincentfrancisco7477 2 года назад
Nag welding po kc ako ng muffler tip, need removed neg terminal ng batt. After napansin ko upon starting boss nag 1500 rpm sya pero after awhile bababa sya ng 1000 rpm. One thing p po n noticed ko pag nk stop ako bigla rumatas rpm at mefyo sumisibat yung car. VIOS 2018 AT po yung car. Need po b relearn? Thanks boss
@Viosified
@Viosified 2 года назад
Hi sir. In case malikot pa rin po ang RPM, pwede mo po subukan i-reset. Para po sa automatic cars, just perform STEP 1 for 10-15 minutes. Then , i-reconnect mo na po ang battery and start the engine. Let it idle until the RPM goes down to about 900 - 700 then turn on the AC while idling for 5 minutes. After five minutes, idrive mo po si Vios for at least 15 - 30 minutes with AC "ON." idrive mo po sya at different speeds para marelearn din nya ang mga shifting parameters. The initial run may be slightly rougher than usual, pero normal lang po yun during the relearning process. Mag-i-stabilize din po sya after driving the car around a few times or a few hundred kilometers. The ECU will continue to relearn as you use the car hanggang sa mag adapt na nya ulit sa driving habits mo po sir. (Pero in case hindi pa rin po sya matulungan ng basic reset na kagaya nito even after driving the car for a few hundred kilometers, pwede mo po gamitan ng OBD2 scanner para icheck po kung may na trigger na errors, perhaps during welding) Salamat po.
@kylevincentfrancisco7477
@kylevincentfrancisco7477 2 года назад
@@Viosified well noted boss. Thanks. Keep safe!
@Viosified
@Viosified 2 года назад
@@kylevincentfrancisco7477 Thank you sir :)
@ryemancer
@ryemancer 8 месяцев назад
Pwede kaya ito sa toyota altis 2015?
@Viosified
@Viosified 8 месяцев назад
Pwede po
@ryemancer
@ryemancer 8 месяцев назад
@@Viosified na try ko na pero di siya bumaba ng 900..till 1200 lang siya..bababa pa kaya ito sir?
@Viosified
@Viosified 8 месяцев назад
@@ryemancer pwede pa po, pero depende rin sa feedback na natatanggap ng ecu base sa kundisyon ng makina, o kung nasa gear o nasa neutral ang transmission, kung naka-on o off ang ac, pati po yung load ng kuryente sa alternator at yung kundisyon ng mga sensors. Meron po ba kayo pinagalaw sa makina bago nyo napansin yung pagbabago sa rpm?
@inspectorwhite1171
@inspectorwhite1171 6 месяцев назад
ilang odometer po bago maglinis ng throttle body?
@Viosified
@Viosified 6 месяцев назад
Depending on usage, every 30,000 km - 50,000 km po for preventive maintenance.
@d-godfather
@d-godfather 2 года назад
Boss flasher relay location? Nabaklas ko na buong dash, wala ako nakita. Wala na kasi audible feedback ang turn signal at hazard nung car ng sister ko na 2016 Vios E, di kaya integrated na sa control module yung flasher relay?
@Viosified
@Viosified 2 года назад
Yes sir, maari po. Kasi 10A fuse lang ang nasa engine compartment fuse box (No. 18 slot) para sa turn signals/hazard lights. Pag ni-trace po tunog ng flasher nanggagaling sya sa likod ng dash panel mismo. Maaring electronic circuit relay na po ang nakakabit instead of traditional relay. Maybe casa could help with specifics. Salamat po :)
@d-godfather
@d-godfather 2 года назад
@@Viosified thank you boss sa info 👍👍👍, baka nga integrated electronic circuit na, based sa research ko wala rin ako makita na flasher relay sa fuse and relay diagrams. Based sa diagram at sa nakita ko habang nagbabaklas, IG1 (Ignition) relay at aircon relay ung malapit sa A pillar sa driver side sa likod ng instrument cluster, sa likod naman ng radio fog relay, rear fog relay and tail lamp relay ang nakita ko.
@Viosified
@Viosified 2 года назад
Thank you also for your inputs, sir. Much appreciated :)
@lester4752
@lester4752 2 года назад
pano mag reset ng srs airbag sir..bigla nalang umilaw sir
@Viosified
@Viosified 2 года назад
Ipacheck nyo po muna sir kung ano ang cause. Babalik kasi ang warning light kung hindi maiaayos ang dahilan. Minsan yung clock spring ang may problema , o kaya may naputol na wire sa harness ng SRS, etc., etc.
@mohamadnazri7307
@mohamadnazri7307 3 года назад
Push start button use the same method? Because push start button different with use key
@Viosified
@Viosified 3 года назад
For cars with push button start, just perform step 1 for 10-15 minutes. Next, start the engine and let it idle until the RPM goes down to 700 - 900 then turn on the AC for about 5 minutes. After five minutes, drive around for at least 15 - 30 minutes with AC "ON" to allow the ECU to relearn the new parameters. The initial run may be a little rough during the relearning process but it will eventually stabilize after driving the car around a few times. The ECU will continue to relearn the more you use the car.
@mohamadnazri7307
@mohamadnazri7307 3 года назад
@@Viosified thanks for ur information. From Malaysia 👍🏻
@mohamadnazri7307
@mohamadnazri7307 3 года назад
One more thing. After i do throttle body. If nothing happen. Rpm all okay. I no need to reset the ecu right?
@Viosified
@Viosified 3 года назад
@@mohamadnazri7307 Yes, no need to reset ECU if everything is okay :)
@Viosified
@Viosified 3 года назад
@@mohamadnazri7307 you're welcome! I'm glad to help :)
@bepositive14344
@bepositive14344 Год назад
applicable po ba yan sa coldstart or kelangan normal temp na ang engine bago gawin ang ecu reset. thank you
@Viosified
@Viosified Год назад
Pwede po kahit cold start
@bepositive14344
@bepositive14344 Год назад
@@Viosified thank you
@edwardcordova9070
@edwardcordova9070 2 года назад
After cleaning po ng throttle body, iac valve ang intake manifold ng vios gen 1 automatic ko, tumaas po yung menor niya ng close to 2000 rpm. Ano po kaya ang possible cause and solution sir.
@Viosified
@Viosified 2 года назад
Naghi-high rev po makina pag nalinisan ang throttle body kasi naalis na po ang dumi at mas madaming hangin na po ang pumapasok sa intake kaya nalilito po ang ecu dahil lumang parameters pa rin po ang sinusunod nya. Subukan nyo po ireset ang ecu sir para marefresh ang throttle position memory sa ecu.
@edwardcordova9070
@edwardcordova9070 2 года назад
@@Viosified mga gaano po katagal bago po bumalik sa normal sir? Salamat po sa sagot niyo
@Viosified
@Viosified 2 года назад
After reset (pag wala po ibang issues), baba din po agad ang idle rpm after a few minutes sa nornal range na 600 - 700 (ac/ off) or up to 1k (ac on). Maaring medyo rough po sa umpisa ang idling habang nagrerelearn ang ecu kaya gamitin nyo po ang sasakyan (slow - fast - slow driving) gaya ng dati para matutunan ulit ng ecu ang dating driving habits mo sir.
@edwardcordova9070
@edwardcordova9070 2 года назад
@@Viosified salamat po sir
@Viosified
@Viosified 2 года назад
Ok sir
@raziqrafiuddinrizal9013
@raziqrafiuddinrizal9013 2 года назад
Hi sir is this applicable to toyota vios 2005?
@Viosified
@Viosified 2 года назад
Yes sir
@ranjatribe
@ranjatribe Год назад
Paps effective din po ba to para sa may check engine?
@Viosified
@Viosified Год назад
Kailangan po ma-identify at mai-ayos muna ang cause ng CEL, kasi babalik po yun kung irereset lang nang hindi nai-repair ang dahilan. Examples po ng pwedeng maging cause ng CEL 👉 ru-vid.comt-JBbJBCWZI
@lorimermonterozo7482
@lorimermonterozo7482 3 года назад
Sir pwede ba mag pa service.. Salamat po 😊
@Viosified
@Viosified 3 года назад
Salamat po sa tiwala sir. Unfortunately, I can't provide services at the moment :)
@salih-hussiend.goling610
@salih-hussiend.goling610 8 месяцев назад
Nasaan naka lagay ang ECU?
@drixgumidam6221
@drixgumidam6221 2 года назад
Gud eve bos, paadvise sana ako kxe ang idle Ng vios ko ay masyadong mababa, binaklas q kxe stater nya dahil pinaayos q at nung ibinalik Kona ang starter, nag iba na Ang pag andar Ng sasakyan q, masyado na mababa Ang idle, NASA 500 lng Ang rpm at nag iba na Rin ang hatak, ty Po, Isa Po aq sa mga likers Ng vlog nyo, ty
@Viosified
@Viosified 2 года назад
Hi sir. Kung nag disconnect ka po ng battery nung binaklas ang starter, maaring na-erase po yung previous ECU parameters kaya nanibago ka po sa behaviour ng engine. Kung sa hatak naman po, walang direct na kinalaman yung starter dahil ang tungkulin lang po nya ay paikutin ang flywheel para sa initial start-up ng makina. Pag pinaandar nyo po ang A/C, tataas pa po ng bahagya ang rpm. Kung manual po ang Vios nyo maari nyo po subukan ang steps na nasa video. Idrive nyo rin po ang sasakyan ng ilang kilometro na naka-ON ang A/C para mapabilis po ang relearning process ng ECU. Kung wala po ibang problema ang makina, unti unti po na babalik ang dati nyang behaviour matapos mag relearn ang ECU. Kung may pagkakataon po kayo, mas mabuti na mapa check nyo ang sasakyan gamit ang OBD2 scanner para mas comprehensive po ang diagnosis at malaman ang totoong kundisyon ng makina, mga sensors, fuel trims, etc. Salamat po.
@joncea4448
@joncea4448 10 месяцев назад
Sir naglinis ako ng MAF Sensor then di ko pinagreset ang ECU at ginamit ko na sya ng ilang araw, need ko pa rin ba gawin itong mga steps na tinuro mo? Salamat
@Viosified
@Viosified 10 месяцев назад
Kung sa MAF sensor, no need na po ireset kung di naman na-trigger ang CEL at walang issue sa engine performance. Usually ginagawa ang reset pagkatapos linisin ang throttle body.
@jpauljusto5893
@jpauljusto5893 2 года назад
Para saan po yung pag apak nyo ng gas pedal at nasa ACC lang po yung key? Salamat po lods :)
@Viosified
@Viosified 2 года назад
Para lang po ma-facilitate ang pag read ng ECU sa bagong max/min throttle position parameters. Salamat po.
@akosipinch8592
@akosipinch8592 Год назад
Same lng din po ba sya sa dual vvti? Salamat po. New subs po
@Viosified
@Viosified Год назад
Same lang po. Thank you, sir.
@ferdiebiojon8761
@ferdiebiojon8761 2 года назад
I tried this but it doesnt work at all..i even follow the specified time...
@Viosified
@Viosified 2 года назад
What's the issue with your car sir?
@ferdiebiojon8761
@ferdiebiojon8761 2 года назад
@@Viosified the issue is code U1001 its about ECU need to re set. My car is a Nissan March k12, i did the same thing exactly what you did, i thought it will also be applicable to other cars other than vios...
@Viosified
@Viosified 2 года назад
@@ferdiebiojon8761 I see. This is mainly for Toyota Vios ECU, but at least you tried. Thank you for your feedback. :)
@jamescasibang3422
@jamescasibang3422 2 года назад
Sir ask ko lng bat mahaba idle ng Vios ko.. naglinis lng po aq ng mag sensor?
@Viosified
@Viosified 2 года назад
Hi sir. I-clarify ko lang po, mahaba po ba o mababa ang idle? Anong sensors po ang nilinis at ano po ang ginamit na cleaner?
@jamescasibang3422
@jamescasibang3422 2 года назад
Mababa po idle.. maf sensor po, contact cleaner po sir.. Pero ok na po sir binalik na sa dati rpm nya.. nilinis lng po throttle body... Tnx po.. godbless
@Viosified
@Viosified 2 года назад
Salamat din po sir. God bless 🙏
@carlomaverickespina1428
@carlomaverickespina1428 2 года назад
ang galing.. kusang bumababa pala RPM bos noh? wala kang iba ginawa noh? hehe
@Viosified
@Viosified 2 года назад
Yes sir, kusa po sya bumababa after reset. Wala po ko iba ginawa hehe
@carlomaverickespina1428
@carlomaverickespina1428 2 года назад
@@Viosified thanks sir info po. Susubukan ko po yan sir. 🙏🙏
@Viosified
@Viosified 2 года назад
Ok po sir 😊🙏
@Viosified
@Viosified 2 года назад
Ok po sir 😊🙏
@simonlubao8040
@simonlubao8040 3 года назад
bakit yung vios namin superman 2015 ang haba ng redondo po bago mag start sguro 5secs. ikot starter bago umandar?
@Viosified
@Viosified 3 года назад
Hi sir. Maaring low fuel pressure po ang dahilan kaya matagal ang redondo. Pwede nyo po yan itest: 1) Ilagay nyo lang muna sa "ON" yung susi for about 5 seconds or more para makapag prime yung fuel pump. 2) Then tsaka nyo i-start makina. Pag nagstart agad, mababa o mahinang fuel pressure po ang problema.
@simonlubao8040
@simonlubao8040 3 года назад
@@Viosified pag matagal nakapahinga boss ung oto e ayun matagal redondo . Pero pag pinatay ko tas start agad e ang bilis mag start
@simonlubao8040
@simonlubao8040 3 года назад
@@Viosified palitin na po fuel pump pag ganun?
@Viosified
@Viosified 3 года назад
Kung ganun po, mababa nga po ang fuel pressure nyan. Pag ipinahinga nyo na kasi ang sasakyan unti unti na bababa ang fuel pressure sa fuel line pag defective ang pressure regulator (or check valve o may leak sa fuel injectors) kaya pag inistart nyo uli matagal na naman ang redondo kasi kailangan nya pa ipunin ang required fuel pressure para paandarin ang makina.
@Viosified
@Viosified 3 года назад
Ang maaring sanhi po ng problema ay yung pressure regulator or check valve or fuel injector o kaya maduming fuel filter.
@leonardobustarde1663
@leonardobustarde1663 Год назад
8
@daricktimbreza9034
@daricktimbreza9034 2 года назад
Sir pwede po reset ECU toyota altis 2002
@Viosified
@Viosified 2 года назад
Yes sir
@daricktimbreza9034
@daricktimbreza9034 2 года назад
@@Viosified thank you po sir
@daricktimbreza9034
@daricktimbreza9034 2 года назад
@@Viosified tanong lang po paano magpalit ng cabin filter toyota altis 2002 1.8 thanks...
@Viosified
@Viosified 2 года назад
Halos pareho lang po ng steps dito: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-M9s82TnUBe4.html Meron lang po kayo i-disconnect na lever sa right side ng glove box, then squeeze lang po ninyo both sides ng glove box para mahugot po sya. Nasa loob lang po yung cabin filter housing. Same area po ng nasa video na to: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-M9s82TnUBe4.html
@patrickandrewongsitco8257
@patrickandrewongsitco8257 2 года назад
Hi sir! Question paano ba malaman if need na linisin ang throttle body? And after cleaning ba need kagad reset ecu? Vios gen 3 2017 car ko. Also ano ba normal idle speed ntin pag on ang ac?
@Viosified
@Viosified 2 года назад
Hi sir. Ilan po sa mga senyales ay rough idling, mahina o delayed ang hatak, malakas sa gasolina, minsan bigla namamatay makina parang sakal, pwede rin po ma-trigger ang Check Engine Light, at pag sinilip ang throttle may carbon build up na sa butterfly valve at loob ng throttle body. After throttle body cleaning nagbabago rin po ang reading ng ECU sa airflow vs throttle position kaya maaring tumaas ang idle RPM at minsan biglang nagagalit ang makina habang umaandar ang sasakyan. Pag ganun pwede po ireset ang ECU para ma-relearn ang bagong throttle position. Normal idle speed range po pag naka-ON ang A/C ay 650 - 900.
@patrickandrewongsitco8257
@patrickandrewongsitco8257 2 года назад
@@Viosified thank you sir! Very informative video mga ginagawa nyo! New subscriber nyo ko. Keep it up sir!
@Viosified
@Viosified 2 года назад
Maraming salamat po sir :)
@patrickandrewongsitco8257
@patrickandrewongsitco8257 2 года назад
@@Viosified hi sir good morning! Nakapaglinis nko throttle body then reset ecu paano ba malaman na reset na ecu? 2017 automatic po car ko.
@Viosified
@Viosified 2 года назад
Hi sir. Makikita po difference sa behavior ng makina. Kung naging mataas o erratic ang RPM after throttle body cleaning magno-normalize po sya after reset, babalik po sya sa nornal idle RPM range na 650 - 900. Kung may Check Engine Light po bago mag-reset, usually nawawala na sya after. Yung system clock po nagre-reset din. Minsan, after reset medyo nagiging rough po ng konti ang makina habang nagre-relearn pa ang ECU pero nag no normalize din po sya after 50km - 100km run. Kaya habang dina-drive po ang sasakyan unti unti rin nire-relearn ng ECU ang bagong driving parameters at nagaadjust sya accordingly.
@renzoadriano5383
@renzoadriano5383 2 года назад
Sir pano po pag naka delete pala Ang check engine light. Pano kaya mapagana ulit
@Viosified
@Viosified 2 года назад
Hi sir. "Delete" as in inalis po ba ang bulb ng CEL? (Di ako sure kung tama pagka intindi ko sa question) Upon start up, nakikita nyo pa po ba na umiilaw momentarily ang symbol ng Check Engine sa instrument panel?
@renzoadriano5383
@renzoadriano5383 2 года назад
@@Viosified upon start up wala po Yung ilaw eh
@Viosified
@Viosified 2 года назад
Baka po busted na yung bulb ng CEL. Pwede po sya palitan. Pwede rin po gamitan ng OBD2 scanner para i-check kung may error codes.
@renzoadriano5383
@renzoadriano5383 2 года назад
@@Viosified ok po sir pa check ko nlng kung busted na Yung bulb. Eh pano po kaya kung pinalitan na ng bulb tas di parin umilaw
@Viosified
@Viosified 2 года назад
Kailangan po ng tester para ma-check ang continuity ng circuit
Далее
How to reset ECU And relearn Electronic TB (Tagalog)
6:51
PCV VALVE - You MUST Clean This! | Vios/Yaris
6:41
Просмотров 130 тыс.
КРАСИМ ДЕНЬГИ В РОЗОВЫЙ!
01:01
Просмотров 423 тыс.
Toyota Idle Reset / After new battery
2:23
Просмотров 153 тыс.
SYMPTOMS NG SIRANG ECU.
17:02
Просмотров 35 тыс.
WARNING FOR TOYOTA VIOS OWNERS IN THE PHILIPPINES
10:46
How to reset idle on ANY Toyota car!
1:54
Просмотров 466 тыс.
Personalized Resin Gear Shift Knob 🚗✨
0:56
Просмотров 3,3 млн
РЕЗКА РЕЗИНЫ ДЛЯ ШИН
0:40
Просмотров 7 млн
РЕЗКА РЕЗИНЫ ДЛЯ ШИН
0:40
Просмотров 7 млн