Тёмный
No video :(

PL/US[part 2] valve adjustment Yamaha XVZ 1300 Royal Star Venture 2003 90890-04105 how to use wrench 

Slavic Riders
Подписаться 180
Просмотров 7 тыс.
50% 1

OEM: 90890-04105
ENG // [subtitles] how to use wrench to remove schmis. Part of valve clearance.
PL // Jak używać oryginalnego klucza Yamaha demontażu płytek zaworowych.
Moto // Yamaha XVZ 1300 and similar
TDC, luzy zaworowe, regulacja
[ADS] MUBI, wyszukiwarka tanich OC: mubi.pl/id-XGNLLF

Опубликовано:

 

22 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 5   
@Jodyrides
@Jodyrides Год назад
I have had three Yamaha ventures. I’ve had Kawasaki, 1973 Z1 903cc.. They all take the same valve shims… keep a record of the size of the gap/clearance. for each cylinder. If possible, record the numbers on the shim for each valve. You may run into A situation where you can swap two shims between two different valve adjustments, because one may be a bit tight, but acceptable, and one may be a bit loose, but acceptable. And you can trade shims on those particular valves to bring the clearance more in line for two valves.. always install the shims with the writing, facing the engine/valve. If you install the shim with the etched numbers on top, the cam will wear the numbers off and you will have to get the measurement/thickness by measuring it with a micrometer if the numbers are worn off , Because the numbers were facing the cam rather than facing down. always adjust your valves or check your valve adjustment with the engine cold. If you make any valve clearance changes, you must resynchronized the carburetors…. removing the spark plugs, makes it much easier to turn the crank shaft, in order to rotate the camshafts.. always make sure you blow the dirt away from the spark plugs & valve covet before removing unscrewing plugs & balve cover from the head to keep dirt and grit from falling into the cylinder through the spark plug hole.. Don’t forget to put something like a rolled up, paper towel into the spark plug hole to keep things from falling in there with the spark plugs out Never never put the old spark plugs in when you’re done. They are cheap, buy new ones.. if you’re going to go to all this trouble, put new spark plugs in and only use ND or NGK spark plugs.. never use champion, spark plugs in anything you ever own unless there is no other spark plug available for something like your weed whacker or your lawnmower. They are not 100% reliable after the first heat cycle. Don’t buy your spark plugs on eBay. eBay is completely polluted with counterfeit, spark plugs sellers, especially NGK… Buy NGK spark plugs at any motorcycle dealer, advance auto parts stocks NGK spark plugs also. If they don’t have them now, they will have them for you tomorrow...
@kermitbull
@kermitbull 3 года назад
Świetna robota, tym bardziej że do Venture jest bardzo mało jakichkolwiek filmów z serii "zrób to sam" A+++
@masterofbikes2747
@masterofbikes2747 3 года назад
Good job
@FrankNijkamp
@FrankNijkamp Год назад
How did you remove the read camshaft cover?
@slavicriders
@slavicriders Год назад
Sorry, I missed this question. You need to disconnect a coolant pipe on the rear-right cylinder and the plastic cables protector. And squeeze all that electric cables on frame. When you remove carburetors it will be more easier. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HfSF0AMiJFc.html
Далее
2010 Yamaha Royal Star Venture rear tire removal
9:14
Девочки, у вас тоже так? 💅🏻✨
00:17
The Smartest Reason for Correct Valve Clearances!
7:37
Adjusting the Valves on the 07 Vstar 1300
34:58
Просмотров 5 тыс.
Yamaha XVZ ROYAL STAR 1300 VENTURE
2:33
Просмотров 756
XT350 valve adjustment without special tools!
20:25
Просмотров 8 тыс.
yamaha royal star venture clutch replacement
36:46
Просмотров 88 тыс.
Why checking Valve Clearance is VERY IMPORTANT !!!!
6:53
Royal Star Venture fuel filter change
8:11
Просмотров 26 тыс.