PLASTIC INJECTION MOLD SETUP 

Great job and I literally laughed my butt off with the Christmas Story bit! I'm a 60 year old mold setter and I cuss at every change over.

Thank you for the well-executed trials to ensure the product comes out well

Very cool- that's gotta be one expensive piece of equipment!

Beings back memories 30. Years in plastic molding good fun

DME makes a pneumatic coupler for center knock outs. they are a bit pricey but it will save you lots of swearing. also bump the nozzle back and forth a couple times to get the stuck sprue loose.

I don't know why it is so fun to watch someone else work their butt off . Have a Joyous New Year!

I have never seen such a machine before, and I feel amazed by seeing it. Before this, I had only seen a machine with one injections unit...😮😮😮

👍🏻Отличная работа. Я сам занимаюсь литьём пластика уже 12 лет. ХАЙТЬЯН отличная машин! У меня сейчас КАЙ МИНГ.

Great video, I have done blow moulding for 42 years so very informative, thanks for sharing.

Every video you make is a master class! Thanks for taking the time to bring us along.

Shakespeare 😏the wacking of the sprew.😅

Good work! I recommend visiting a plastic injection molding company and observ a quick and safe tool change. It will definitely make your work easier and faster. But, job well done.

Wow that is a monster size machine!

Pretty cool video. Custom sprue Wacker lol

Nice work😊

Good videos . I was a Machine setter before, and I do have some comments and points to add. 1.) I suggest you add a leveling tool to ensure the mold is properly leveled before closing the mold. because you might close it unlevelled. 2.) I Don't remove the chain block support even though you have fully clamped on the fixed side. There are times that a mold setter have not fully tightened the brackets on one side and the mold droops or worst fall. I removed it when both A&B sides are bolted on the platen. If one of the A/B loose support or fall from plates, it will hang to the other half. 3.) Remember to put hard hats when moving molds overhead. sometimes eyebolts clips breakout or not fully locked.

why screwing back was slow back pressure. enjoying this

I noticed you said you don't really have to run water through the molds.. does this cause zebra striping for you or ghalling of the tool? Having them watered can help you choose where you want the parts to stay as well and help with the flow of the plastic and the cooling process to be shorter. What do I know, I'm just a mold setter.

👍

That is a clever trick with the integrated tunnel gate cutting. 👍. Would a tapered hole for the tunnel gate help reduce the chance of the center stem getting stuck?

Can you share the equipment you use?thank you🙏🏾

nice Mr

Bro look like Spider man, Peter Parker 👍👍👍

Why not use a locking coupler on ejector rod?

Can you share a link for the McMaster material you used?

Using this ejector extension rod means rotational table cant rotate right? Sprue stuck you might be can reduce gate seal time or make undercut pin to pullout runner

What are the equations used in machine settings?

how did you center the tool? i didnt see a centering ring

i am a tool setter, why not open the plattens, then eject slowly then connect the coupling

How much does the plastic cost per part? How much does each part sell for?

Pero el molde ya tendria que tener las placas aislantes incorporadas

no cooling ? is the nozzle tip the right size? sorry ill shhhhh

It's doable unit

setup molds

Please add polish subtitles :)

Amazing work as always served part of my Apprenticeship in the mold shop here in the uk…you need a bigger shop looks like a right nightmare chaining loading and clamping…not easy for 1 man with a manual crane as well…respect

Why wouldn’t you just bolt the insulator plates to the mold. I would be afraid that that ejector rod would snap when running. Then finally why wouldn’t you torque those toe clamps in.

You take off the strap and crane before u close B half of mold....i make sure all 4 bolts are in bedore i take crane away just a safety with me but to each it own...also u dont use a level as well..

Waooo my dream job Can I please join you

I'm spart

we are mold maker in Shenzhen China, please contact us if need make plastic injection molds.

Take the carriage back before trying to remove a sprue

So much I've seen wrong, can't watch anymore! you sir be safe, and you need to clean your shop. I have fired employees for leaving less of a mess! And for gods sake, get a safety panel over that control panel with all the exposed wires!

WHAT Really I'm a PROCESS TECH , You sir are a beginner at best like the vid you should see the real world

Nice shop, nice equipment, however the most backward thinking on molding I have ever heard. 40+ years in the business and never heard so much crap that I have heard on your channel.