Polaris Pro to Khaos Conversion for Under $200? WHAT!!! How to do it and What to Buy! 

Nice! Thanks for the feedback. It should be pretty simple for anyone that wants to do it! It makes it super playful!

Yes 155 and 165 with the 3.5 pitch tracks (not sure on the 3.0 pitch but my guess would be no) do have a factory anti stab kit. I don't know on the pro shock length myself and can't verify but that would be interesting. I did the footage for this video prior to the release of the matryx platform so it may not be completely up to date with the current. Appreciate the info though!

Thanks! Without lengthening the shock you risk overextending it and shock damage. You won't get the full benefit without doing it.

I'm using the upper hole of the two spots on my tunnel for the front track shock. That's the hole that the khaos uses and that's what I was after was for it to act as close to the khaos as possible.

If you have the longer limiter strap, longer shock, and an anti stab kit I would just install all of those on your Pro rails and you will be set to go. That's what I did in this video. I did not buy separate rails.

Thanks I appreciate it!

I softened the rear a little but not much. You definitely would benefit from a longer track shock but be sure to do the anti stab before as well. It will drop the front down further to begin with and give you more ski lift without compromising your preload on your shocks. I think you'll be very happy with it once you do it.

If you trimmed down the tips of the rails correctly there isn't any way at all for the rails to spear the track. The anti stab kit will hold the track away and force the track to roll around the ends of the rails with pretty much 0% chance of catching.

No the khaos doesn't come with that hole drilled so I left it in the original position.

Yes you can out those on and do the other things in the video. My intention with the video was to show you could convert for cheap. The velocity shocks aren't typically cheap which is why I didn't include them.

No I left mine in the upper hole which is the hole that the khaos comes in stock.

I'm located in Idaho. I don't have a website right now. Just fb pages and an eBay store as of right now.

No I did not see any wear. There should be almost no chance of it wearing as it should "roll" right around the tips as long as it doesn't have any material sticking past the wheels. I would double check that and then double check the rear of your rails to make sure the aren't too close to your track back there.

If you are going to buy new fox shocks then I would just get some khaos ones. Otherwise any will do as long as they're coil overs. From what I've heard the air shocks can't be lengthened nearly as easy or cost effective. I really like the qs3 coil overs with the lockout on this setup.

I can't say for sure but you should be able to check but checking the clearinance in the top of your tunnel and in the front of the tunnel. For example, If you have a 2 inch track already and have 1.5 inches of clearance then you'd be good. Your track will have some flex to it as it turns so you want to take that into consideration when measuring because you will need extra space above it. Also a 2.86 track usually has 7 tooth drivers. I would see how many tooth drivers you have right now and make sure 7 tooth would fit but I believe you may have 8 tooth? You can use different driver tooth numbers but then you'll have to play with gearing more.

Yes you can but without putting a longer limiter strap you won't get the khaos benefit. If you lengthen the strap then I highly recommend the anti stab kit as it drops your rail tips down and increases the chance of sticking one of your rails through your track windows.

It will for sure be the same on any from 2016-current.

Very useful video Lifestyle. But I have a related question. I have a Pro Matrix and it uses the upper hole. It seems to me that using the lower hole would raise the front end 1 inch the same as lengthening the FTS travel. This would make the sled easier to get and hold an edge since it can roll over much easier with less weight on the skis. But it doesn't seem like it would make it wheelie more because the angle of the torque arm provides the lift and that would not change. My understanding is that the power of the engine is transmitted from the rear wheels through the skid and up the torque arm to the chassis, but that angle doesn't change unless you do the normal conversion. I guess the hole is for other models in the family but perhaps I could get better handling without the wheelies by using the lower bolt. Seems like something for nothing, which is almost never true. What's your take?

@@michaelhansen7516 I have to apologize as I never saw this message nor was I notified you commented. I am not overly familiar with the lower mounting hole to be honest. I know that it's considered the "assault" hole as the assaults were mounted in that hole with similar rail profile to the khaos but there was a lot of different opinions as to the handling of the machine. I know there were a lot of complaints about the trenching in that position but essentially that's what the lhaos does as well. It'd be interesting to try a pro in that hole vs a khaos to compare. I'm sure there would be a lot of similarities but I'd be more interested in the negatives as well.

I have to apologize to you as well since I didn't see this comment. I haven't played around eith that hole too much or almost not at all so I can't speak from any experience. The lower hole was the "assault" hole and helped with better response for the racers and keeping the front end up more for flying through the moguls from what I heard. From what I understand it also help increase responsiveness from rider input and less of a planted feel. Before it was known as a trenching machine and I beleive that's why a lot of people went away from it for the backcountry. Times have changed now since then so maybe that's why polaris created the khaos-to create another trenching machine as a playful backcountry machine instead of a climber since we've move that way as a mountain segment as a whole??? It'd be interesting to see the differences between the assault setup and a khaos first hand.

@@lifestylepowersportspartsa4587 getting near that time again. The dealer thinks it might work. I'll report back if I try it out. I can always put it back so it seems worth a try. I'm expecting to lose the way the pro tracks a sidehill but gain the edge on crust and keep the way the pro jumps on top of the snow. Beats me. My khaos 165, I don't really care for the trenching, but then I'm not yet good enough to take advantage of it.

If you watch the video it shows the difference between the pro and khaos skid angles. Hence the reason for the anti stab kit. It's close enough where the anti stab kit goes that although it may not be perfect khaos it will put you pretty darn close and that last tiny bit you will not notice.

This setup is creating essentially the same geometry as the khaos. All the difference in the khaos rails is that the end of the rail is tipped up so they dont stab through the track window since they dropped the front of the suspension. Elevate spindles would be fine with this. I am running the skinz freeflow front end which also raises the front like the elevate spindles and have had zero issues with great handling.

@@lifestylepowersportspartsa4587 sick thanks you are always on top of it.

I didn't do the actual lengthening of my shock so I'm not entirely sure what was done other than that it works! Lol. Andy Youngstrom at Gas Shock Repair in Idaho could probably give you a better idea than me even trying. We have re-used the springs that each of the shocks we've done came with stock.