Тёмный

Preparations for this set of small wind turbines to be mounted up in the air - mast is almost ready 

Modern Ukrainian Homestead
Подписаться 420
Просмотров 479
50% 1

‪@ModernUkrainianHomestead‬
A couple of mistakes are there on the mast...
They have to be fixed:
1. The lever - must be longer, at least two times, maybe even 2.5
2. The winch is awful, that one has to be replaced.
3. The stopper has to be added, to mechanically limit the tower lowering
About the turbines - they are a set of those that were tested in different ways everywhere here on the channel before, and will all finally be mounted to actually work.
1. S3 - 40 watts max, no over-expectations. but whatever it delivers - all is mine.
2. small vertical X3 (was not present here in this video, but appeared in some of my other videos here too) - regardless it may get 1-4 watts maybe, again, anything it delivers - all is mine.
3. M3 - I expect it will be able to shine at 300-500 watts mode. question is with which wind wheel. I doubt that the 1.3m 5-blader will be able to give it a nice slow wind start, but let's see...
4. the self-made wind turbine from the generator I've been testing in junction with the S3... It should fly at likely the same values M3 will. but again let's see.

Наука

Опубликовано:

 

29 май 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 9   
@bermudatriangle2036
@bermudatriangle2036 Месяц назад
I'm very excited to see these turbines up in the air, I think the masts you build could support much bigger turbines.
@ModernUkrainianHomestead
@ModernUkrainianHomestead Месяц назад
yes, they are for potentially up to 2.4 m diameter machines. those I have currently will be 1.65 only.
@bermudatriangle2036
@bermudatriangle2036 Месяц назад
@@ModernUkrainianHomestead I can give you files to 3d print 2 meter diameter turbines.
@ModernUkrainianHomestead
@ModernUkrainianHomestead Месяц назад
Well, I don't have a place to do that. And those printers that work now - they produce drones, so are quite busy
@bermudatriangle2036
@bermudatriangle2036 Месяц назад
@@ModernUkrainianHomestead printers are not expensive anymore and there is no shortage of them, I use an elegoo neptune 3 max. I print in my kitchen. at the moment I am printing a 2 meter long blade, so its for a 4 meter diameter turbine.
@ModernUkrainianHomestead
@ModernUkrainianHomestead Месяц назад
@@bermudatriangle2036 I will definitely think of that option, thanks for a hint!
@NoSpamForYou
@NoSpamForYou Месяц назад
It looks like the middle unit you could slide the tail a few inches back to the end of the pipe to improve the tracking a bit. An idea for people that don't want to replace the pipe.
@NoSpamForYou
@NoSpamForYou Месяц назад
I just saw on your other video there is a third rivet on the other side of the tail. So it would only have 2 connections if you move it down.
@ModernUkrainianHomestead
@ModernUkrainianHomestead Месяц назад
yes, theoretically possible. need to have a proper tool for it still
Далее
ROCKET that LITERALLY BURNS WATER as FUEL
19:00
Просмотров 558 тыс.
готовка с Даней🥹
00:59
Просмотров 448 тыс.
ЛУЧШАЯ ПОКУПКА ЗА 180 000 РУБЛЕЙ
28:28
Uncovering The Genius of Fibonnaci Turbines
17:42
Просмотров 586 тыс.
I Built an Atmosphere Powered Battery..
13:00
Просмотров 639 тыс.
Electro culture Antennas
6:22
Просмотров 7 тыс.
How the UN is Holding Back the Sahara Desert
11:57
Просмотров 13 млн
The Problem with Wind Energy
16:47
Просмотров 1,9 млн