Pressure Pot vs Vacuum Chamber | Resin Dice Casting

Подписаться 202 тыс.

Просмотров 213 тыс.

50% 1

In this video, I go over the differences in Pressure Curing Resin for Dice Making, vs using a Vacuum chamber to remove the bubbles in your resin.
In essence, you can do EITHER, but the pressure pot works BETTER at getting you a consistent results with your dice making, with a lot less work on your end. Just put it in and forget it.
When curing with a pressure pot, the bubbles in your resin/silicone casting become so small, that they can't be seen by the human eye. When using a vacuum to remove the bubbles from the mold in your casting, you pull the bubbles WAY too far out of the mold, leaving you with not enough resin to finish your casting.
Now you CAN vacuum out the bubbles, and then pour it, but you run the risk of just adding bubbles at that stage anyway.
So really, my money is on getting a pressure pot over a vacuum chamber. It does two jobs, and I'm told that it can cure your silicone for your molds in the same way, but I have yet to try that myself. So take THAT part with a grain of salt.
Amazon Affiliate Link to the resin material that I used. Available in smaller batch sizes as needed: amzn.to/2KXlUkY
Amazon Affiliate Link to the mold material I used: amzn.to/2zccY5P
Amazon Affiliate Link to the Vacuum Chamber Kit: amzn.to/2PGwPU6
Harbor Freight Pressure Pot that I use/adapted for Resin Casting: www.harborfreight.com/2-1-2-h...
If you like twitter, I got one! / rybonator1
I also have an Instagram! / dm_rybonator
If you have any ideas for what you would like to see built/reviewed in the future, let me know in the comments down below! Then subscribe so you don't miss any new videos coming out in the future! Also, if you liked this, gimme that sweet sweet like.
MUSIC:
• "Renaissance Period" "...
"Renaissance Period" "Music For RU-vid Videos" "Royalty Free Music"
LAKEY INSPIRED - Better Days
• LAKEY INSPIRED - Bette...
Resin Safety Data Sheet: cdn.shopify.com/s/files/1/121...

Хобби

Опубликовано:

1 ноя 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 668

@ScrapwoodCity 4 года назад

I don't have a pressure pot so I can't judge it. But the vacuum works for me. The problem with all the guys that test the vacuum with resin is that you let the resin overflow. You don't have to do that. You can first degass the resin in a separate container and then pour it into your mold. Also you can adjust your molds so that your resin can overflow a little bit. You also must let some air go out before the overflow, then stop the process and then repeat a few times. You don't have to fully degass the resin to have a clear cast with a naked eye. It definitely works for me and my projects are proof of that. Anyway that's must my honest opinion! :)

@Rybonator 4 года назад

That's a totally fair and good point! I was wanting to show the difference in the set it and forget it style. BUT if you are willing to do the adjustments or watch the vacuum, it works just fine. Thanks for the tips :)

@sageslarres 3 года назад

@@Rybonator im sorry but you cannot use the same procedure when doing 2 completely different things. This is as if you would try to show flaws with the pressure pot by putting pressure on the resin before pouring and then "setting and forgetting". Its obviously not going to work due to what you are trying to accomplish and the materials you are using. Also degassing the resin beforehand in a bigger container could be seen as easier since you can pour a lot more quicker and cure outside the chamber.

@Nstone53 3 года назад

Honestly I don't have either but even I was skeptical of his method while watching. I wanted to get my husband a vacuum chamber years ago for his mini dnd figures he makes but I never did. Then recently I started looking into ways to make dice, as a hobby gift to him. But when I saw this I was shaking my head saying "This feels so bias. That's too long isn't it?" Thank's for clearing this up. I think I'll need too look at more comparisons still. lol

@gilbertcabasse6168 3 года назад

Would it be possible to take advantage of both processes? I would say: 1) eventually cool down the resins A and B before mixing, to have a longer pot life, 2) use the vacuum for a little while to remove a good portion of the air, going slowly, progressively for 5-15 minutes to prevent overflow. I suppose you can this way at least reach 0.1 bar, which means 90% of the air is gone. 3) then apply pressure and let the resin set. Would this process give a clearer result than using only pressure? One more question linked to the previous, and also for those without budget to buy both devices: I understand that you cannot at all apply pressure in a vacuum chamber, but is it possible to apply vacuum to a pressure chamber? I don't see why (apart maybe a question of connector) you could not do that....So, with my process above, you would not have to move your mold between both stages!

@gilbertcabasse6168 3 года назад

I have zero practice in casting resin, but I am an engineer, I don't understand why applying pressure works so well... From physics, the volume of a gas is inversely proportional to pressure (PV=nRT, so at constant temperature, Pressure*Volume=constant ), which means if you go from 1 bar (ambient pressure) to 4 bars (read 3 bars on the manometer since graduated a 0 for ambient), you then multiply the pressure by 4, so the volume of the bubble is divided by 4. The volume of a sphere is (4*Pi*R^3)/3, so a sphere B of 1/4 of the volume of a sphere A has only its radius diminished by cubed root of 1/4, which is 0.629 . So, by applying 3 bars, the spheres should have their radius not even twice smaller... This is all in theory. But pressure has long proved that it's working, so I must be wrong somewhere... Notice here that I am thinking while redacting.... ...Now I have checked: your explanation of why pressure is working is partially wrong: the bubble are not disappearing because the pressure are pressing on them, reducing their volumes, but because the capacity of the liquid to dissolve the gas depends on pressure. It's what happens in a bottle of sparkling water: when it's still under pressure, the water is perfectly clear because the gas molecules are intimately mixed with the liquid, there are no bubbles at all. When you open the bottle, the pressure is reduced, and the bubbles appear. So my previous post should be wrong, no need to apply vacuum before pressure, if it's dissolved, it is clear, it cannot be clearer. But it should also explain why you can apply pressure to silicone: once the bubbles dissolved, there are no bubbles at all, just gas molecules trapped in the solidified matter, that cannot grow bigger. It should also be a track to test whether it is useful to apply a deep vacuum to get rid of the bubbles. As soon as you have de-saturated the liquid (let's say at 0.5 bar), when the pressure is back the excess air of the original bubbles should dissolve, and any bubble disappear. May be this could avoid many spill out...

@ArcAiN6 4 года назад

I want to point out there's a flaw in your methodology here. 1) You don't need to pull a vacuum that long. 1 maybe 2 minutes is sufficient 2) You don't pull a vacuum on the mold. especially if it's a silicone mold, as bubbles trapped in the mold can expand, and deform ruining the casting. pull the vacuum on your resin before pouring, and be gentle and steady with your pour. 3) When you pull the vacuum, you are drawing trapped gasses out of the fluid, when you release the vacuum, remaining bubbles collapse (such as when you are applying pressure) Because of atmospheric pressure. You pull the vacuum to remove the bubbles, then pour it into your mold. No need to maintain a vacuum. With the pressure method, you have to maintain pressure during the curing process, or the bubbles will simply expand again before the resin has set. The biggest difference here, is equipment usage. With a pressure system, you can only work as many pieces as can fit within the vessel at a time. With a vacuum system, you can cycle more pieces at a time, by vacuuming the resin, then pouring it, you considerably increase .how many pieces you can work with at once, as well as produce a better end result. Pressure does NOT cause the bubbles to completely disappear, and depending on how many bubbles you've formed during mixing, could leave the piece with far too many occlusions. Finally.. a combination of the two processes would result in near flawless results. As with anything in life, the effort you put in, is the proportional to the results returned.

@Rybonator 4 года назад

This is absolutely right! I have since been more educated about the process since this video's inception. My main concerns with pulling and releasing the vacuum, were 1, it takes more effort than the set it and forget it of a pressure pot. And 2, I was worried about running out of time when degassing, and my resin starting to cure. Because I've never had an issue with bubbles in my dice after the pressure pot, even with a HUGE amount because of my sprue molds, I never have bothered with both results. If I was making these for a museum quality replica, I would probably go with both methods now, but as this is just a hobby, I'll stick with what works for the time being :) Thank you for the tip!

@benjaminhowell6920 4 года назад

Firstly, thank you for an educational video and comments. My question to your reply on degassing the resin before pouring in the mold is what happens when you cast a highly detailed mold? Air would still be trapped in the mold no? So surely from an efficient point of view it would simply still be better to pressure cast? Secondly, how do you clean your pipettes after casting? Thanks!

@FreefallVector 4 года назад

@@benjaminhowell6920 You just throw away the pipettes, normally. :P Getting resin out of those would be an ordeal!

@D3DW1TCHCHIK 4 года назад

So just put the cup of your resin in the chamber and let the bubbles rise before pulling it out?

@fabo1328 4 года назад

@@Rybonator ArcAiN6 said in point 2) that you shouldn't pull a vacuum on the mold, because it could ruin the casting. In your previous video (part 1) you achieved a great outcome with that method. Would you stick to that method or did you ever experience any deformations in your molds?

@mrjutsumaster 4 года назад

When you pull a vacuum, as the bubbles start rising, you let air back in, that'll pop the bubbles and let the resin sink back down. Repeat til there's no bubbles.

@Rybonator 4 года назад

Yes absolutely! It's more labor intensive than a pressure pot, but doable. You still have to worry about adding bubbles back in during the pour, as well as possibly running out of time as the resin begins to cure, but doable!

@indecisiverift 4 года назад

@@Rybonator longer working time resin should help, yes? I'm not sure how many options for resin are out there that have the structural or visual qualities you're going for.

@noelr9376 4 года назад

Indecisive Fom what I notice the vast majority of resins on Amazon are fast cure. You need not just slow resin for degassing, but very slow resin which is harder to find and probably more expensive. For what he’s doing and the type of resin he’s using it probably is better just to pressurize.

@mrjutsumaster 4 года назад

@@noelr9376 the opposite for me. The only resin I can find are slow cure epoxy.

@noelr9376 4 года назад

mrjutsumaster I’m not talking about cure times, I’m talking about the working time of the epoxy before it begins to gel. Please tell me where you are finding an abundance of slow work time epoxy. Most I see are 15 minutes or less.

@simpson6700 4 года назад

how can a completely clear D20 look so beautiful? ...i may have a dice addiction.

@Rybonator 4 года назад

Then you have come to the right place! haha :)

@jamiemartinwebb 3 года назад

Best explanation of the difference between using a pressure pot and a vacuum chamber for resin projects that I have seen to date, and he didn't spend an hour telling it either. Well done.

@Rybonator 3 года назад

Thanks Jamie! :)

@ClokworkGremlin 4 года назад

I would like to add an addendum to the "pressurizing" segment: The amount of pressure in your pressure pot isn't enough to account for the level of shrinkage in the bubbles. For example, let's say you live at sea level (14PSI) and you pressurize your pot to a very generous 60PSI. That's roughly 4x the pressure. Our Ideal Gas law states that if you increase the pressure by 4x, you reduce the volume by 75% (4x the pressure, 1/4 the volume). Diameter is a function of the cube root of the volume, so a 1mm diameter bubble will be reduced to 0.63mm. That's still more than half the diameter, and would be pretty visible. However, increased pressure also results in increased *solubility* in a solvent. Think when you open the cap on a pop bottle, all the bubbles come out. That's because the pressure inside has been reduced, so the carbon dioxide is less soluble in the water, and gets released. Now, epoxy resins are made of pretty reactive materials. That's *why* they turn from two liquids into a solid, and release heat in the process. It's also why un-cured resin is actually very toxic, and why some things can cause the resin to "inhibit" and not cure properly. Increasing the atmospheric pressure also increases the solubility of air into the liquid resin by about 4x. So basically, my assumption is that the increased pressure causes the air bubbles to be absorbed into the resin the same way carbonation is into fizzy drinks. This, plus the internal stresses that pressurization adds, does reduce the physical strength of the cured resin, however most epxoies have such a high tensile strength (usually 1500PSI or more) that this isn't really a problem. Generally what I've gathered is: You want to vacuum-degas silicone molds (partly because silicone usually just has a longer working time and won't set in the middle), and you want to pressurize your resin (because most molds don't have enough overflow capacity, and the set time is fast enough that you can get stuck in the middle somewhere.) Also, comments on technique: You want to actively watch your vacuum chamber and repressurize whenever it gets close to overflowing. This is tedious, but will help prevent overflows.

@EntropicCheese 4 года назад

I have no idea if what anything you just said is true but I have been searching for some kind of answer to why pressure pots work because there is no way air compresses that much especially at like 40psi. I'm just a layman but apparently nobody has really done the science on it, that I can find at least.

@ClokworkGremlin 4 года назад

It's not something that's easy to research, since it's kind of hard to really test for such things when the solvent is under pressure. The best I can really say is "It makes sense," but that's admittedly not a very good barometer for factuality. Maybe we could convince someone like NileRed or Cody's Lab, who actually have some fairly extensive chemistry knowledge, to come up with some experiments.

@Rybonator 4 года назад

I love your explanations, very detailed and easy to follow. Thank you for the addition to the knowledge :) There is also a bit of natural shrinkage that happens when resin solidifies and cures, which also plays a part in the overall reduction of volume. This in combination with the bubbles and your explanation create the results that we see. :)

@ClokworkGremlin 4 года назад

Thanks. Fortunately, I have some work experience explaining technical things to nontechnical people (I would like to emphasize, not *stupid* people. My boss is very intelligent, but her expertise lies in running a store. If she had technical expertise, she wouldn't need me.) but I know I can get extremely wordy and dense sometimes. I've had a few people say they think I would make a good teacher. To which I respond, "No, I would make a terrible teacher!" Ultimately, though, I just love talking about the things I find fascinating, and spreading the knowledge I've accumulated. Perhaps, in some way, it's my own bid for immortality, that a hundred years from now, the things I once knew will still be remembered. I'm glad people seem to appreciate it.

@wuerfel_schmied 4 года назад

Absolutly yes to bring gases into solution. With the cured resin I'm really not sure what happens with the trapped gases. Maybe they just difuse over time. I don't think they really bring any stress to the material. Frozen cola does not crack and break when you open the bottle, but as its melting, the gases also get released and bubble out. Do you have any resources to that topic? I found nothing so far about pressurized resins and the impact on material properties.

@greyadams1057 4 года назад

4:17 you said "one of the dice" not "one dice" so it actually is correct

@ostyx4037 4 года назад

ONE DICE is not correct. ONE DIE is correct however.

@greyadams1057 4 года назад

@@ostyx4037 he said ONE of MANY like "one of the children" or "one of the animals"

@ostyx4037 4 года назад

Ah ok. Dice.

@kennethcoffee8631 4 года назад

Lawful good grammar nazi

@Rybonator 4 года назад

I can't even get my corrections for that right lol. Thank you for the clarity :)

@vanakornsirijongprasert1726 2 года назад

I love how informative and educated this video is, this video deserves more likes.

@rebeccadahlberg8758 4 года назад

This was insanely helpful! My husband and I have been researching and couldn't find any clear cut answers. You're awesome.

@Rybonator 4 года назад

Well thank you :) I'm glad you found it helpful!

@sgtcrtrdnl 4 года назад

excellent vid! I cant tell you the number of times ive explained this to people, seems like every other day someone is asking about pressure/vacuum in resin casting. Now i can just send them the link to this video! Very well explained.

@Rybonator 4 года назад

Glad you found it helpful :) I had a lot of people asking in the comments on my previous vids, it was just easier to make this one to show people, as a visual is just a better tool!

@spencer_sunboy 4 года назад

how I mean this in the best way possible, but there is nothing that puts me to sleep better than your videos! If I need a nap, I just put on your dice making playlist and I'm out. Super relaxing, and a very nice voice!

@Rybonator 4 года назад

Honestly that is one of the best compliments that I have received :) I love listening to maker vids to fall asleep to, and I'm glad I can provide that for someone else. Have a great night's rest my friend!

@thegamingpikachu6784 4 года назад

Yes I was waiting for this type of video! I want to get into dice making and I've been wondering about this. Thank you so much!

@Rybonator 4 года назад

Glad I could help :) Thanks for watching!

@thegamingpikachu6784 4 года назад

Rybonator also wanted to tell you, I did read somewhere that a pressure pot doesn't help with bubbles for silicone type things. Not sure if it's true or not but thought you should know

@sinikkaparton 4 года назад

This is super straight-forward and helpful! I can't find any type of pressure pot available for purchase in Norway, so I was thinking of just getting a vaccum chamber - but now I know that wouldn't be ideal! Thank you for saving me the time and money (':

@MrPBJT 4 года назад

Hi! Jula sells something similar as calling it a "trykkfat" No idea if it is any good though, reviews seem kinda bad.

@Rybonator 4 года назад

Glad to help where I can :) Best of luck in your casting journey!

@Dinomannen 4 года назад

The one from Jula looks like the same one as Robynator uses in his videos. All the reviews pertain to bad O-rings in the hose for the paintgun(easily fixable) and should not interfere with using it for resin-casting. As far as i've understood the reviews atleast.

@Dem0n1337 4 года назад

You can still use a vaccum chamber. However you need to pull the bubbles out of the mixture before you put it in the mold. Both can work, its just that they have two different methodologies.

@stankrieger3598 4 года назад

pressure cooker you would use on your stove can be a good start. I am using a pressure pot used for painting. ck HF store. or amazon

@pasu2k 4 года назад

This is exactly the kind of video I hoped you would make, I was wondering about this, and now I know the answer! :)

@Rybonator 4 года назад

Glad it was what you were looking for! :)

@camsolberg1761 7 месяцев назад

the video was very informative and cleared up my questions re pressure pots and vacuum chambers, thank you!

@magicmurlo 4 года назад

It was both informative and entertaining! So mission accomplished both tasks set forth for you. Good job Dice lord!

@Rybonator 4 года назад

Thank Murl! I always look forward to your comments :)

@Gothorella 3 года назад

Thanks for sharing. this was super helpful!

@RadioFixer 3 года назад

This is an awesome video, answered all my questions about what to use. Thank you very much!

@QuizMasterEntertainment 4 года назад

This was certainly informative, I'll be sure to keep it in mind if I ever get to work with resin

@Rybonator 4 года назад

Glad you found it helpful :) Thanks for watching

@sebastianelford9830 3 года назад

Thank you for another great video, you’re really helping me along my side journey

@onar_ 4 года назад

This was awesome to watch. I now have more learn.

@Rybonator 4 года назад

Thank you for that :) I appreciate hearing that others have learned from my videos.

@BananaDucshortz 4 года назад

This is the kind of video I needed. Thank you.

@Rybonator 4 года назад

Of course! Glad it was what you were looking for :)

@bigkittytank 4 года назад

Thank you for breaking it all down and showing us the results for our specific application! I have been wondering why not to just use the vacuum chamber for everything, as in theory it would be better. But now I SEE why to use a pressure pot.

@Rybonator 4 года назад

It really helped me to visualize it as well when I first experimented :) Glad you found it useful!

@davidmathieson8661 4 года назад

Depending on the working time of your resin you could do both, first vacuum before the pour then pressure after filling to minimise any added bubbles. This route is obviously more expensive and time consuming but it would be an interesting experiment...final word though I do agree for simplicity/result/cost effectiveness go with a pressure pot

@Rybonator 4 года назад

Absolutely you could! And I'm sure some meuseum quality resin displays of art probably do this to ensure that their work is perfect :)

@zacpackman9186 4 года назад

this is the awsome content that i subbed for. thanks rybonator keep up the awsome work.

@Rybonator 4 года назад

Thank you for that :) I'll keep making if you keep watching!

@NicnacSaurus 3 года назад

This is exactly what i needed to see! Thank you!

@tonyblake7569 3 года назад

Amazing, thank you. Before I thought a vacuum chamber would be a better idea because removing the bubbles sounds better than making them smaller, as long as the resin didn't set before it did it's job, but didn't consider it expanding like that.

@strawberrylemonade785 3 года назад

I am FINALLY going to make dice and the first tim I was going to make dice I found your channel...so thank you for making your channel 😌

@Rybonator 3 года назад

Happy that I can help :D

@idmikajo99 4 года назад

The use of of the vacuum pot is to pull the bubbles out of the epoxy before you pour the epoxy into the molds. Yes, you may introduce bubbles while pouring, but they will not be as bad.

@Rybonator 4 года назад

True, but you could still overflow from your cup, and you might introduce some bubbles, AND you have to worry about cure times in your resin while you are doing that, and it's labor intensive instead of set it and forget it. But it can work :)

@yugos.oficial 4 года назад

@@Rybonator if you want the best finish, you have to pull out as many bubbles as you can before make them smaller with the pressure pot. Overflow problems? You just have to use a 3 to 4 times the volume of the resin cup, pour the resin into the mould, and compress the small amount of bubbles left. Only by using both methods you will achieve a perfect copy of your models. If curing time is a problem go for another slower curing time resin. I consider that is not fair the fact that you only show a resin cup and a mould overflowing everywhere, it is just a wrong way to proceed and a lot of people who are starting casting can be confused. I have to dislike this video dude, it just shows wrong content.

@frankwick3989 3 года назад

I feel like it's also worth noting that your example used a simple form that allows the bubbles to rise straight out of the top of the mold. In many cases the mold will have air trapped inside that won't simply rise to the pour hole. It will expand and stay inside the complex form unable to rise out. Thanks for the video! so cool.

@AJ-jj9fc 4 года назад

Solid work Professor Rybonator! This was great.

@Rybonator 4 года назад

Please, Professor Rybonator is my father! You can call me Doctor Bonator.

@Rybonator 4 года назад

Also thank you lol :)

@amywike1196 6 месяцев назад

This is a great video for tactile learners. Thank you!

@sarah_van_ 2 года назад

This was super helpful, thanks! 🙂

@BrutusNii 4 года назад

I really like this informative video, plz continue! :D

@Rybonator 4 года назад

Thank you :) I appreciate that. Will do!

@dantuck5552 4 года назад

I was having a problem with my silicone molds and decided to try my pressurepot. It worked like a charm. No more little bubbles on my castings!

@Rybonator 4 года назад

Fantastic! I plan to show that in a future video as well, so I'm glad it worked for you before I try haha :)

@kirajones1650 4 года назад

It was really interesting to see the difference between them!!!

@Rybonator 4 года назад

I love watching the vacuum being pulled on the resin haha :)

@collettemustill6492 3 года назад

This is incredibly helpful thank you

@meathelix 4 года назад

I've just started wading into the whole mold making and resin casting scene, and this video helped clarify the pressure vs vacuum topic immensely. Thanks!

@Rybonator 4 года назад

Glad to help where I can :) Welcome to the hobby!

@stankrieger3598 4 года назад

Thank You finally a clear answer to my big question. Great demo and explained very clear. sorry for the play on words there but supper job. Now I will build my pressure pot.

@Rybonator 4 года назад

Haha that's good :) Glad I could be of help!

@johnspetkitty81 4 года назад

Thank you for this! We'd been wondering which to get, and this definitely finalized it. Now...to just get the money for a pressure pot and compressor.

@Rybonator 4 года назад

Yeah they are not a cheap investment, but if you are planning to sell your dice ever, I 100% recommend it :) Can't wait to see what you create with them when you get em'!

@roguedeath98 4 года назад

This is super helpful, was just considering getting a vacuum chamber, so, yes super helpful.

@Rybonator 4 года назад

Still a useful tool! But a pressure pot is just more bang for the buck :)

@uselesswriting3092 4 года назад

Would definitely recommend the vacuum chamber! Might be a bit more work but definitely more proper. (And overall can be cheaper).

@EstablishedLowriders 3 года назад

Great work, thanks for sharing!

@paulwestreicher9795 4 года назад

I was really close to buying a Vaccum and pressure pot but now i'll wait until you upload a silikon mold made with pressure instead of vacuum. From an egoistical point I'd like to ask you to do that soon! Love your videos! always a great help and very straight forward! Keep it up!

@Rybonator 4 года назад

I might have to up the schedule I had planned for that :) Glad you find my stuff useful. Thanks for watching :)

@palgaea 4 года назад

Super awesome and informative video mate! Im starting myself on moldmaking for some figures and i was thinking on buying a pressure pot but i didn't knew much about the differences of the machines.

@Rybonator 4 года назад

Hopefully this helped in some small way to make your purchasing a bit more clear :) Glad you liked it!

@TarotMom86 4 года назад

I would LOVE to make my own dice someday, so knowing this information is vital! Thanks for saving me money (in the future when I actually have the funds to buy my equipment lol)

@Rybonator 4 года назад

Of course! Happy to help in some small way. Can't wait for you to get the equipment! You are gonna love it :)

@maiax3i 3 года назад

Oh man, you just saved me of buy the wrong way to cast my resine, thank you so so much

@Rybonator 3 года назад

Of course! :)

@niklar55 3 года назад

Thanks for the demonstration. I did a search, specifically to find an explanation of this, and got exactly what I needed to know. From other processes, like kilning clay pots, and allowing moisture to escape, it occurs to me, that the vacuum, would need to be applied very gradually, to give the bubbles time to move to the surface, _through_ the resin, rather than bring loads of resin out with them. Maybe, like cooking clay, you would need a timer, that could follow a programmed schedule. Watching bubbles escape, is not far removed from watching paint dry!😉 I also wondered what the difference would be regarding light transmission, if you were making lenses, say for old lamps or similar. I suspect even bubbles that you cannot see, would affect light transmission.

@TupmaniaTurning 4 года назад

Very helpful video - thank you.

@Rybonator 4 года назад

Of course! Glad it helped :)

@Faustvonholle 4 года назад

Shoutout to TheCrafsman! I love his videos and I'm really liking yours since I came across them!

@Rybonator 4 года назад

Hey thanks! Glad you like them :) I have some crafsman inspired stuff coming up soon!

@nigromarte7017 3 года назад

Helped A LOT. Thank you!

@benddeg 4 года назад

Thank you so much for this!

@Rybonator 4 года назад

Of course! :)

@VickiBowers 3 года назад

Oooh, that SteadyCraftin’ reference! I’m subscribed now! Great vid, too. Thanks 👍🏻

@vonkachez 3 года назад

Super helpful video🙂👍

@Phantomtkd Год назад

Fast forward to future episodes when he shows ways to use the vacuum chamber and not lose any resin and do it much better lol.

@deveshwarisingh1784 3 года назад

Informative...thanks to put this vedio...👍👍

@hikerdude5265 2 месяца назад

Very informative, thanks.

@juceeyj 3 года назад

You just went Bill Nye on me (thumbs up) ! Great explanations.

@RobSandstromDesigns 5 месяцев назад

Excellent information.

@frogicus 4 года назад

Great video !

@sobertillnoon 3 года назад

Dear Sir, Your not wrong to say "one of the dice". Because it is one of a group and the group should be plural. If I have 10 cats and want to pick up one, I will pick up one of my cats, not one of my cat. Your usage of the plural in this case was correct. Thank you for coming to my Ted talk.

@MileyonDisney 4 года назад

Looks like it's gonna be a pressure pot for me! Thanks!

@debbieappelman7861 3 месяца назад

excellent explanation! I use both silicone and resin so probably need both a vacuum pump/pot and pressure pot. I also need to purchase an air brush compressor. This is quite a bit of equipment so I am trying to research how to economically buy all of it. But pressure is best for clarifying resin and good for resin poured into silicone molds. Silicone is better to de gas in vacuum.

@vizionthing 4 года назад

You pull a vacuum on the resin before pouring , never while its in the mould!

@Rybonator 4 года назад

Oh absolutely! You absolutely could pull, release, pull, release etc, but it both takes practice, and is more labor intensive (If you wanted to do it in the mould). Not to mention that you have to worry about your cure times if you don't degass fast enough. Compared to the set it and forget it pressure pot, I just prefer it :) But it's a totally valid, and probably proper, method! But yes, vacuum before pouring :)

@Recommendedforyouall 4 года назад

vizionthing 7:36 dude. Next time watch the whole video, and be sure to listen

@davejohnson5278 4 года назад

@@Recommendedforyouall yes, he does say you can do it but you take the chance of putting bubbles back in your resin. Most videos I've seen of people who use the vacuum method use the longer working time resins. The way it's done in the video is very skewed towards the pressure pot that beginners that didn't know any better would swear you couldn't use a vacuum system.

@stormorr9727 4 года назад

This is super helpful! Thank you

@Rybonator 4 года назад

Of course! Glad you found it useful :)

@pannakreatywna8064 4 месяца назад

Thank you for that video :) its very helpfull ❤

@davidbui1151 3 года назад

Thank you! I used the vacuum and my materials got real hot and time constraint was an issue as you mentioned!. Great advice.!!

@joeguilfoyle1922 2 года назад

Thanks for that. Great info. Now I'm looking for the video to convert the HF pressure pot. It didn't show up in the corner like you said. I'll find it. Thanks again.

@josephp8712 4 года назад

Hey boss what exactly did you do to "adapt" it for resin casting? thanks

@emoemi907 4 года назад

this is suuuuch a helpful video!!!!

@Rybonator 4 года назад

Glad you liked it :) Thanks!

@LukeStephenson 4 года назад

Very informative. That's exactly the info I was looking for. Pressure pot it is.

@18deadmonkeys 2 года назад

great video!

@abcsolution 3 года назад

Thank you, super good video. Top !!!

@VulpeRenard 2 года назад

I have heard a general rule of thumb is that vacuums are okay for silicone but pressure pots are what you need for resin. I've only just started so all I know is from the flood of YT videos I've been watching lately. Also I love that little D20 hat that comes out of the vacuum chamber. It could probably make a nice board marker or mold registration key.

@Z12901 4 года назад

This was very helpful

@Rybonator 4 года назад

Thank you :) Glad to hear that!

@JonMW 4 года назад

Great video. The vacuum seemed like the more intuitive method so I wondered why you were using the pressure pot. I am sure glad that I didn't buy a vacuum chamber last week.

@Rybonator 4 года назад

Pressure pot all the way for dice making! Though you CAN make a vacuum work :)

@AlexanderSterling9 3 года назад

Very informative and easy to understand. I’m a little unsure of what you mean by “adapted” your pressure pot. How did you adapt your pressure pot? Is the pressure pot model you use safe to use for those that are starting out or for experienced maker? Are there different models? Thank you!

@BenHayat 4 года назад

Thank you so much to clarify this difference between the two. Do you recommend a small Pressure pot and pump combo that I can buy to create small objects? Most pressure pots I saw, assumes you already have an air pump. Thank you again. ..Ben

@vilian4373 4 года назад

Thanks for clear explanations. Exactly what I wanted to know regarding resin casts, in a way I could understand without feeling like an idiot 👌

@Rybonator 4 года назад

Glad I could help in some small way :) I'll do the feeling like an idiot, so that you don't have to haha

@Gureiseion 4 года назад

And here I thought my plans to diy a vacuum chamber was a bad option. Thanks for this!

@Rybonator 4 года назад

DIY vacuum is a safer option than a DIY pressure pot at least haha a:)

@benb3316 4 года назад

Thank you! I'm looking into both but already have a pressure pump vs a vacuum pump!

@Rybonator 4 года назад

Of course! I will be putting out a video soon comparing the use of the two on silicone as well :)

@jacktjong1266 4 года назад

I'm not a dice goblin and even I know you don't vacuum pull a mold. Vacuum pulling the resin ahead of time, then pouring it into the mold is a lot more convenient in my opinion than leaving the dice in a pressure pot. The pressure pot needs to be turned on the entire time while the resin is curing, and depending on what method you're using to keeping the pressure pot pressurized, it can be pretty loud. A vacuum chamber needs to be active for a few minutes, until the resin doesn't look like it's foaming anymore, and then it's ready to pour and you can just leave it over night. It's basically just the same process as a pressure pot, but instead of pouring first and putting in a pot second, you put it in a vacuum chamber first and then pour it.

@stillnotstill 4 года назад

Neat! Never would have thought to wonder about the differences since I don't make anything with resin but it was so cool to see the side by side results. The full d20 was so pretty and clear, but like... the partial one looked epic. I need some desk sculptures of partial dice sitting in puddles of resin like they melted, or even a partial d20 without puddle to game with (not to roll of course but to like.. keep the other dice company / just add to the collection) Some of my favorite dice are weird, with paint where it shouldn't be or not where it should be, or an old d20 that appears to be from the first d&d, so old and beat up and chipped that it's not for rolling fair anymore. Uniqueness is beautiful to me and while I have wanted to make dice since starting watching your channel, this video really inspires me to make failed dice one day.

@Rybonator 4 года назад

Well I have tons of oddly shaped or uneven dice from my escapades in dice making, so there are some really "unique" dice that you would probably enjoy :)

@anandsoni9316 3 года назад

Thanks for the video, what will you suggest for the jewellery casting, pressure or vacuum ?

@Perdullune 4 года назад

Thank you so much for this video! I'm searching for casting videos because I'm willing to do silicone casting. In this case, which one would be better to make solid silicone objects: the vacuum chamber or the pressure pot? Do you know it?

@bonafidecustoms4479 3 года назад

Thanks for the video

@darthdadpool3402 4 года назад

Rybonator love your videos and you inspired me to get into the molding and casting . My first set of molds produce the same results of rough surfaces when pressure cast. So instead of putting the silicone into a vacuum chamber, I put set #2 to cure in pressure pot at 50 psi and produces very good results

@Rybonator 4 года назад

I actually have a demo of that planned for my next video! I got the same results :) Good to know great minds... get similar results haha

@darthdadpool3402 4 года назад

My last batch of silicone I used was clear but I misread the viscosity. It arrived and I saw how thick it was (very close to caulk from tube). Being a 2 part mix it was strewn with air bubbles. I figured I would give it a shot and see just how good a pressure pot was. Low and behold a clear mold was produced. Wish I could post pics of the initial and final results for you

@nicholasgazzano8002 3 года назад

What do I use to clean the cups I put the part A and B in? I’ve heard that either acetone or alcohol but not sure if that’s true.

@yarelysreyes6977 3 года назад

Hello!! Your video is exciting!! Did you make/change anything special to the pressure pot you bought at Harbor Freight?

@carlosorozco5666 5 дней назад

Thanks a lot men, this exactly what i need to know.😁

@jordanvega1666 4 года назад

Hi! After reaching the desire PSI on the pressure pot do o I need to leave the air compressor on?

@natashalogan5317 4 года назад

I don't know if you have considered this but it would be so cool to see you make beginner tutorials. Like how different resins compare pressure pot vs vacuum with silicone. How to dye resin and different ways. I know you've shown how to do these in your videos but videos just dedicated to those would be really cool!

@Rybonator 4 года назад

I absolutely plan to make a beginner video soon :) I wanna show the steps from the very beginning for beginners to above!

@natashalogan5317 4 года назад

@@Rybonator that's fantastic I'm looking forward to it 😊