COCKPIT/ENGINE PRE-START CHECKS
1. Pedals and seats - Adjust
2. Seat belt - Fasten and adjust
3. Circuit breakers - All engaged
4. ECL's - Confirm at FLIGHT
5. All switches - OFF or closed
6. ENG 1 and ENG 2 MODE switches - OFF
7. ELT switch on instrument panel - Confirm ARM
8. LDG GEAR lever - Confirm DOWN
9. External Power (if used) - Connect and switch ON
10. Ground support personnel - Connected (If required)
11. BATTERY MASTER - ON
12. ♦ Main and Aux Battery - ON
13. EXT PWR - ON (if required)
14. ♦ GEN 1 & 2 - ON
15. ♦ BUS TIE - AUTO
16. POSITION lights switch - Confirm functioning then
leave as required
17. ♦ ANTI-COLL lights switch - ON. Confirm functioning
18. LT Panel switch - ON. Confirm emergency
lights functioning:
cabin (2), sponson (left and right), cockpit door (left and right)
- OFF or ARM, as required
19. MFD - Set SYSTEM page, select
SYS CONFIG, verify
system part number
20. MFD - Set PWR PLANT
21. ♦ CAS messages - Check
22. ♦ MFD - Check fuel quantity
23. ♦ LDG GEAR panel - Check 3 green lights and
EMER DOWN
24. ♦ PARK BRAKE - Pull and turn handle and
press pedals until PARK
BRAKE ON advisory illuminates
25. ♦ RAD MSTR switch - As required (GND if
battery start)
26. ♦ FORCE TRIM switch - ON
27. ♦ CLTV/YAW TRIM switch - ON
28. ♦ AWG switch - As required (REGRADE or
or INHIBIT position disables "150 FEET" voice message)
29. LD-SH switch - TORQUE
30. AFCS - Confirm not engaged
31. Cyclic stick - Centered
32. Collective lever - Full down, friction as
required
33. Flight Controls - Push ELEC PUMP on HYD
panel. Carryout cyclic, collective and yaw pedals full and free check. Utilizing the cyclic position indicator, on PFD, centralize cyclic control. ELEC HYD PUMP select OFF.
34. HYD SOV switch - Centered and guarded
35. ♦ FIRE WARNING TEST - Press, on the TEST
control panel, BAG and confirm the warnings.
- Press, on the TEST control panel, ENG1
and confirm the warnings.
- Press, on the TEST control panel, ENG2 and confirm the warnings.
36. FUEL pushbutton - Press. "TEST" replaces
"FUEL" on MFDs
37. CHIP DETECTOR pushbutton - Press ENG 1 pushbutton
and confirm CAS caution: 1 ENG CHIP and MCL illuminates.
- Press ENG 2 pushbutton and confirm CAS caution: 2 ENG CHIP and MCL illuminates.
38. AWG TEST pushbutton - Press, momentarily, on
the TEST control panel AWG. Confirm audio tone and voice warning(s).
39. ♦ OIL LEVEL - Press MGB pushbutton
and confirm CAS caution: MGB OIL LOW and MCL illuminates.
- Press IGB pushbutton and confirm CAS caution: IGB OIL LOW and MCL illuminates.
- Press TGB pushbutton and confirm CAS caution: TGB OIL LOW and MCL illuminates.
40. ♦ LAMP TEST pushbutton - Press and confirm all
lights illuminate.
41. FLOATS switch - OFF
42. HOIST - LT and PWR both OFF
43. SX16 SEARCH LIGHT - OFF and STOW
44. ♦ RPM switch (on collective) - Set 100%
(102% for CAT A)
download: www.helisimmer.com/downloads/...
#helicopterx1 #AW139 #Prepar3D
20 апр 2021