Project FD RX-7: Turbo Upgrade/Install

Подписаться 45 тыс.

Просмотров 3,1 тыс.

50% 1

Tonight we wrap up the turbo upgrades on Quinn's FD and take it for a little spin. Will it boost more?
Support our channel and get some apparel at: slipanglemedia.com/shop
Listen to our PodCast The Corded Tire on ShoutEngine: shoutengine.com/thecordedtirep...
For regular updates follow:
/ slipanglemedia
/ slipanglemedia
slipanglemedia.com
#GarageQuinnMotors
#TheSlipAngle
The Slip Angle Crew:
Quinn:
/ garagequinnmotors
@GarageQuinnMotors
Matchew:
/ matchew_mx5
@matchew_mx5
Music Tracks:
Licensed under Creative Commons: By Attribution 3.0
creativecommons.org/licenses/b...

Авто/Мото

Опубликовано:

31 май 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@mro9466 Год назад

The shape of the FD is timeless 🤤

@astrolightsadventures4677 Год назад

I swear I learned so much for my own car and gained so much appreciation for the way you guys tackle your car builds I appreciate all you guys

@TheSlipAngle Год назад

Awesome!

@Kevin-vg4hu Год назад

swapping out turbo, I would have probably taken that opportunity to swap to an 8374 EFR and haltech. Electronic boost control, CAN Wideband, and CANgauge. That's my plan this winter.

@verdict1163 Год назад

You could linearize the coolant temp gauge in the stock cluster if you wanted to run a boost gauge in the triple pod. It's pretty easy, just requires some soldering of the circuit board. After the mod the stock gauge is accurate.

@wrexz Год назад

Mattchew should be project sloppy seconds rx7

@mattwiser7982 Год назад

Hahahahahahaha

@bobbyrios2k223 Год назад

Glad this is back and running.. such a nice car

@masterkendro Год назад

Awesome car quinn, mattchew let us know of your plans for the FD, stoked to see that get developed. As usual guys I appreciate the content and I wish yall nothing but success with the channel, keep the videos coming!

@arrivendrive6831 Год назад

Awesome to see the Fd back. I run the ohlkms dfv and they are awesome!!! I would not run more than 16lbs on 93 pump gas. I would run more than 16lbs if I ran on ethanol. You should be very close to 450rwhp with 16lbs on o3 octane. You are smart not to go too hard on boost without a returne. What are the seats you run on the car? I am 6'2 and I want to wear a helmet for track days. I can't wait to see more Fd content. Brap on brother

@howzertech2222 Год назад

I think that he is using a set of Porsche replica seats. I’m 5’10” and cannot fit win my FD with a helmet on. I tried using a Recaro SPG, which I bolted to the floor using a set of Ronin rails, and my head was still squished sideways against the headliner.

@arrivendrive6831 Год назад

I think the b9 from Tillett may work but I have not been. Able to confirm.

@TheSlipAngle Год назад

For SAE Dynojet HP, I think I'm going to need at least 20 psi to see around 450 whp but we will see what it does when we tune. I have a set of GT3 Replica seats on Nagisa Super Low rails and while not perfect the seating position is much better than stock.

@atotalpro Год назад

This is the ricer content we need.

@TheSlipAngle Год назад

lol agreed

@DEADxCoOL Год назад

Excited to see what will happen with the FD!! On the other hand, I'm peeping the 2 wheels in the corner there. No 2 wheel content?

@TheSlipAngle Год назад

We did some a while back but it didn't do too well

@DEADxCoOL Год назад

@The Slip Angle unfortunately in the U.S. there not a lot of younger folks into bikes

@Lexannn Год назад

When you say limited by compressor cover outlet, are you talking about the cold side intake compressor housing outlet going to your intercooler ?

@TheSlipAngle Год назад

That is correct

@verdict1163 Год назад

Needs a wing to balance the profile, IMO.

@TheSlipAngle Год назад

Duckbill ;)

@mattp9932 Год назад

where did you get the matte cf interior for the stock plastic

@TheSlipAngle Год назад

It's vinyl wrap

@terrybutler3370 5 месяцев назад

What is that turbo manifold you have for the single turbo?

@TheSlipAngle 5 месяцев назад

One my friend and I made

@terrybutler3370 5 месяцев назад

A decent low mount twin scroll manifold is a little challenging to find. RE Amemiya have a stainless one but I don't trust stainless exhuast manifolds on rotaries.

@Powerhauz Год назад

Mazda Mattchew Mods. Mattchew Mods Mazdas. Mattchew's Mazda Mods. Mod Mattchew's Mazda. That should cover your bases. Mcubed. M3. 3M. Idk. Just don't be mattchewing apex seals.