PT14 $500 Fiero GT. $74 Turbo Can Paint job. Is it really worth saving hundreds?

Подписаться 51 тыс.

Просмотров 1,8 тыс.

50% 1

$74 for 6 cans of paint, tape, masking paper pre-taped, 2 cans sandable primer, sand paper and cleaning wipes.. Total was about $170. Links below of supplies
Sanded, bondo a few cracks and nicks, taped, wiped down and Spray! Is it worth saving a few hundred on supplies? I suppose if you do not own an air compressor and want a quick cheap paint job
Associate Links:
6 pack Turbo cans: amzn.to/4aUXMJR
Sandable Primer: amzn.to/3Vwhs1X
Scuff pads, 400 grit: amzn.to/4aRnxdZ
3M 600 grit sandpaper: amzn.to/3VxhN4M
3M 320 grit sandpaper: amzn.to/3yP5bNo
Pre taped masking paper: amzn.to/3RdxsDO
Paint cleaning wipes: amzn.to/3Vd0HHY
Tack Cloths: amzn.to/3VbDR3r
Boss 4x10 dash speakers (listing says 6x9): amzn.to/4bjgA6F
Smart mirror: amzn.to/3TEGjAq
Functional hood louvers: amzn.to/483qKqn
Jet performance Chip: www.napaonline...
Nexar Beam Amazon associate link: amzn.to/4857rMX
Fiero GT Playlist: • $500 1987 Fiero GT
Total costs for this 1987 Fiero GT project:
$500 for the Fiero
Ignition and door locks $50
Shift select cable $93 (had to modify)
PS241 Oil Pressure Switch $73 amzn.to/4921thd
Jet performance Chip $130: www.napaonline...
Hood louvers $63 amzn.to/483qKqn
Fiero GT perfect fit outdoor car cover $53: amzn.to/3PJrpVQ
-------------------------------------------------------------------------------------------
Like my videos? Links below, be sure to like and follow please :)
Fiero project playlist:
Thanks you for watching, PLEASE subscribe!
▽ Follow MotoCheez
Instagram: / motocheez
Facebook: / motocheez
Web: www.MotoCheez.com
Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use.
Audio clips:
Movie clips:
Memes:
#fiero #fierogt #addons #classiccar

Опубликовано:

9 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 91

@billcotton1551 3 месяца назад

"Hit it again!" Hans Gruber, from Die Hard.

@MotoCheez 3 месяца назад

😅😁😜👍

@williamzoom 3 месяца назад

For fresh runs in paint take some painters tape & wrap it around your hand with the sticky side facing out and slap the run with the tape then respray the area again! If you get a run in clear you let it dry and take a razor blade thats had its edge knocked down with some 200 grit sandpaper and you lightly drag the blade down the clear run until its flat then buff it out with some 3M Finesee It II on a waffle pad.

@MotoCheez 3 месяца назад

Thanks! I've heard of that but I didn't think of it at the time

@BillEngrave 3 месяца назад

I would have done flat it seems to lay down better .I would then highlighted it with a glossy strip probably vinyl.

@MotoCheez 3 месяца назад

I did think about flat

@timothybroga1704 3 месяца назад

Not too bad Cheesy Looking forward to see how it stands out. Definitely an interesting project

@MotoCheez 3 месяца назад

Thanks!

@RatdogDRB 3 месяца назад

Lookin' forward to seeing how the block sanding and buffing pans out.

@MotoCheez 3 месяца назад

Me too! 😁

@gregorydeangelis9192 3 месяца назад

Not familiar with turbo cans but a slightly aggressive compound will flatten that finish

@unclemikessouthernoutdoors3783 3 месяца назад

Not bad for a spray can, reminds me of the 80's

@marchufnagel9068 3 месяца назад

Just got the keytag the other day! thanks and car looks nice!

@MotoCheez 2 месяца назад

Great, thanks

@billcotton1551 3 месяца назад

Looks pretty good, Cheezy!

@knerdrider 3 месяца назад

You’re going for the full KARR look on this one! Just need an amber light bar and you’re good!

@MotoCheez 3 месяца назад

😁👍👍

@eiknarf9993 3 месяца назад

After you block it spray some grey then clear the whole thing, it will last a lot longer! Looks good though

@MotoCheez 3 месяца назад

Grey then clear?

@eiknarf9993 3 месяца назад

@@MotoCheez yeah just fix the silver/ gray on the bottom then spray some clear and you'll have a show car!

@MotoCheez 3 месяца назад

@eiknarf9993 ahh. Ok

@chadcarter9581 3 месяца назад

Dude it looks great! If you hate it too much, I’ll buy it

@MotoCheez 3 месяца назад

😁😂👍👍

@josephsaucedo8691 3 месяца назад

Wrap the mirrors with black vinal wrap 💯👍✌️

@MotoCheez 3 месяца назад

I wish I was good at wrapping, I tried it before and failed too many times especially on a curvature that sharp

@josephsaucedo8691 3 месяца назад

@@MotoCheez I'm not very good at it either. My brother can do it. He also does hydro diping. I usually have him do it if I need it done.lol💯👍✌️🤭

@Slane583 3 месяца назад

@@MotoCheez If the mirrors are black plastic you can just sand them down with some fine wet/dry sand paper to give them some tooth and just hit them with a coat of clear that can withstand uv light. It'll make them look like fresh black paint. :)

@MotoCheez 3 месяца назад

It's supposed to be flat like the trim and rear louvers...

@brianl2607 3 месяца назад

looks good!

@Slane583 3 месяца назад

Not too bad for some rattle cans, can't be too picky with enamel paint. Anything can be painted as long as it's prepped properly. :)

@MotoCheez 3 месяца назад

Thanks. True!

@212acres3 3 месяца назад

Sweet

@mojo2131 3 месяца назад

👍

@josephsaucedo8691 3 месяца назад

If you spray it again I would recommend getting better replacmint tips your local paint shop should have them. It makes a big difference. The hood 90 percent of the time does that because it was opened then closed oil deposit in the air get on the hood that's what cause it. At least that's what they tell you when you go to auto motive painting school. If you water sand it really good can paint can come out pertty good. Iv had people ask me if I sprayed it with a paint gun and it was from a can. Lots of sanding. 💯👍✌️

@MotoCheez 3 месяца назад

Someone else mentioned that, I wish I knew before I painted. Lol

@Thebrokehobbyist21 3 месяца назад

Orange peel is from the nozzle/tip orfice not being fine enough to properly atomize the paint molecules being laid down. I had an issue with it when i first started cerakoting with a 1.2mm nozzle. Went down to the recommended .8 and peel was gone. Humidity really only effects the curing time. Block, wet sand, and clay bar. Itll be silk after the end. Could turn into a 8inch paint job after all of that.

@buckwild8920 3 месяца назад

As the saying goes, usually applied to people, (Good from far, but far from good) lol, I'll buy that for a dollar.looks alot better than it did tho.

@outthere2 3 месяца назад

Can't beat the price Cheezy, and at least it's all one colour now.

@MotoCheez 3 месяца назад

True....

@overthehill1958 3 месяца назад

If it doesn't come out, you could always paint it orange.

@MotoCheez 3 месяца назад

😂😂👍👍

@gregorydeangelis9192 3 месяца назад

Now I'm thirsty

@Studio_Earth 3 месяца назад

I'm digging the Fiero content. Sucks the paint laid like it did. I've never personally used the turbo cans, but I just read in a Grassroots Motorsports forum where a few people had mentioned that the turbo cans is gloss black seem to lay a textured finish. One person said it resembled "Drywall texture". In the same forum someone mentioned that the Rust-o custom spray 5 tip nozzles interchange with the turbos for more control over the pattern but I'm not really sure that it would help much.

@MotoCheez 3 месяца назад

I bet if the tip could have been changed to a little finer spray pattern it would have been better. Yes it goes down so fast and volume it does look like its textured

@josephsaucedo8691 3 месяца назад

When id paint things for people when i went to school id use rustoleum paint a gallon was pertty cheap with a harbor fraght gravity feed gun and some reducer. No one could tell by the time i was finished with it. Speachlly if i clear coated it. You could do 2 or 3 cars with a gallon if you sand and clear it. You can get pertty good results. 💯👍✌️

@MotoCheez 3 месяца назад

I painted a jeep same way! I used hardener

@rockcitymarco9186 3 месяца назад

Turned out pretty good 👍 I'm assuming the moisture in the air cause that orange peel although it's a pretty nice job 😁

@MotoCheez 3 месяца назад

I think so as well, it should buff out and look decent by the time I'm done just more work that's all

@hoagiesherlin7732 3 месяца назад

Little cut n buff and it will be pro

@BRIDGEBURNERSTV 3 месяца назад

I used a turbo can a few times recently. Not a fan. Cost $30 up here in Canada. It’s the same cost as a small can of paint the exact same brand and color. However, with the rustoleum paint right into my gun, no thinner or reducer, I was able to cover more truck with 1/8 of can than I was with 2 whole turbo cans. Edit: I did my job outside btw. Yours looks good tho. Nice work.

@MotoCheez 3 месяца назад

I did a Jeep with rustoleum in a spray gun and it came out a little better. Yes it does seem to use more paint. I also noticed the fan is not perfect on the turbo cans so it's heavier in some parts of the fan, the lower part actually and you can't spray perpendicular to the roof it will spit and sputter

@BRIDGEBURNERSTV 3 месяца назад

Yeah it sputters a lot actually if you even tilt it down just a bit. The idea is cool but it’s just not as practical as it looks. You can get a paint gun for less than $20 these days. But in a pinch the turbo can I guess is better than 2 separate spray cans…possibly lol

@MotoCheez 3 месяца назад

@BRIDGEBURNERSTV I have all the spray equipment, I just wanted to try the turbo spray cans cuz I see other people using them. Oh well

@BRIDGEBURNERSTV 3 месяца назад

@@MotoCheez I know you’re pretty geared up. Same here; not as good as you (I’m working in my driveway always) but I tried them for the same reason.

@Motorider2018 3 месяца назад

🔥🔥🔥🔥🔥🔥🔥🔥

@jololaryan7542 3 месяца назад

Looks good bro

@MotoCheez 3 месяца назад

Thanks, hopefully once it's sanded and buffed it'll look better. I've definitely done better work!

@millerhendrix6311 3 месяца назад

That is why I wrap a car, or clay bar before you paint, degreaser isn’t the final step before you paint

@MotoCheez 3 месяца назад

I did use tack rags I just didn't mention it. I scuffed the whole car down with the Scotch-Brite so it would adhere then wipe it down with a oil remover, then use tack rags

@brennenrulez 3 месяца назад

Is this the model with speakers in headrests?

@MotoCheez 3 месяца назад

No unfortunately, those were pretty cool

@camarotwofast 2 месяца назад

Did you spray on that any of that two-part clear in a can with the hardener in it?

@MotoCheez 2 месяца назад

No. I didn't. I wouldn't have anyway because of all the orange peel, going to have to sand and buff it

@douglaslangham4417 3 месяца назад

Orange peel usually comes from not enough surface prep , what kind of decreased did you use ?

@MotoCheez 3 месяца назад

From what I read and painting before it's because of the nozzle not atomizing fine enough. I use those frog wipes or whatever they're called, there was no fisheye or spidering the base was smooth definitely not going to cause the orange peel cuz it was flat

@Sinerwray 3 месяца назад

Going clear it too?

@MotoCheez 3 месяца назад

No, thought about it though

@robertgutheridge9672 3 месяца назад

Wet sand with 1500 then buff it will look better

@MotoCheez 3 месяца назад

I'm going to try that in about a week, hopefully it should look a lot better

@robertgutheridge9672 3 месяца назад

@@MotoCheez you may want to use 2000 . I've painted a few car the same way and a little sanding and buffing they look pretty good

@MotoCheez 3 месяца назад

@robertgutheridge9672 You're probably right

@Yt_xrider 3 месяца назад

Hey mr.motocheez have you had any issue on your china bikes like last gear is limiting topspeed and like not pulling power anymore?

@MotoCheez 3 месяца назад

Only when I had carb issues

@ruby055 2 месяца назад

what was the temp and humidity when you painted.

@MotoCheez 2 месяца назад

Was 78 degrees, but pretty humid

@frankwilliams2198 3 месяца назад

You should have had it painted you would have been alot happier.

@MotoCheez 3 месяца назад

No way, $4000 and up for basic paint job! I'm way happier

@gubr 3 месяца назад

Orange skin? Shark skin for reduced air resistance!

@MotoCheez 3 месяца назад

😁😅👍👍👍

@Foche_T._Schitt 3 месяца назад

Vinyl wrap might have been better.

@MotoCheez 3 месяца назад

The base wasn't good enough for vinyl wrap I would have actually had to paint it for it to stick cuz it was some areas that were completely dry from the Sun. Once I buff it it'll look good

@Foche_T._Schitt 3 месяца назад

@@MotoCheez I've seen people use something like a sandable tractor paint which looks kinda decent but needs buffed more often.

@MotoCheez 3 месяца назад

@fochdischitt3561 I painted my Jeep with tractor paint and a spray gun It came out okay but yeah it fades fast