Brandon, thank you so much for putting this video up, not only for me, but for the many out there who just don't have the knowledge and experience of what is entailed in assembling the parts to convert standard Johnson/Evenrude 9.9/15 engines to electric start and remote shifting/steering. My journey has just begun, but with what you've shown, I can see some light at the end of the tunnel. Thank you!
I have a 1986, 15hp, and someone had made a 1/8" plate steel bracket that mounted I to the front two holes and had a flat that bent forward to attach the steering. They also had attached an arm to this piece, that was used for the shift cable. A one piece solution and worked great. I am currently trying to track down a tiller handle for 1986-1992 motors to convert back to tiller control. If you have a lead let me know. Thanks, and great video!
Hi Brandon I have a 1960 Johnson FDL-14 pull start which I like to convert to electric start and electric choke, could you tell me what parts I need to do this and what years and what horsepower size motors that would work to make this happen. Thank you very much for your time. Cajun
I ordered snap on evinrude cables for my simplex, the new style that has an arm with an eye at the end and they hook up to the motor perfectly However, my simplex is setup to receive the old wire end. Can I replace the plastic guide the cable runs thru in the box or will I need a whole new control box?
i have a 9.9 hp johnson (J10ECUE) 1987 mod. and i want it to be a 15hp, do you know how? I also want to get the motor remote-steering and gass remote (no electric starter etc. I want to keep the old rope start...). Thanks
Hey Brandon, I am looking for a electric start flywheel for a 1988 jhonson 15 it is original rope start and looking to convert to electric start. If you have any tips on where to get one I would love if you could tell me. Thanks
Brandon I have a 95 Johnson 25 hp with tiller throttle. I would like to switch it to remote steering and throttle lever controls. I don’t mind keeping it stock with pull start. I just wanted to know if I could use these parts on a 25 hp instead of a 15. If you could please give me some advice I would really appreciate! Thanks
I have 84 evi 15 pull start! My kill(stop)button is located right where throttle cable goes through there 3:48,4:20! Or explained in a later video? Thanks!
how do you install the brackets for the gear shifter and throttle , i have an older johnson outboard (85 i think) and im struggling to find a kit for it. cheers
There are some low cost ones currently on eBay: ebay.to/2YC0waw and the steering kit: ebay.to/32c5pJD But, you can also piece them together if needed: ebay.to/2XvLCX4 - Throttle Connector Kit ebay.to/2QaJi46 - Shift Bracket ebay.to/2JwPH3a - Shift Connector
Just curious of where u found the attachment for the steering cable to go in. I recently just came across a 88 evinrude 9.9 it has the plate but I'm trying to figure out how to add a steering cable to it.
How ridiculous would it be to just add remote steering/throttle/shifting but keep pull start? Mine is an '88 15hp on a 16' jon boat. Console would be added just forward of the rear bench so the motor would still be within reach... I like the idea of electric start but when I start adding up the parts it's a little daunting when it pull starts quite easily right now. I think I read somewhere that some people do this and they just add a remote kill switch on the console... Maybe I'll slowly look at buying the parts for it... It's likely a winter project.
Ive done it, many many times. Its not the best, but if the engine idles fine, its not that bad. Just a lot of up and down. A remote kill switch is handy
I cant get the throttle hooked up on mine. Mine is a 90s 15hp. The throttle cable I have is way to big to fit around all the gears. Could you message me so I can give you my email and send you pictures of the issue?
