R30 VR6 Engine Build Part 2

Подписаться 38 тыс.

Просмотров 12 тыс.

50% 1

Feta Fam, friends and new comers,
With Stav's wiring done, it's time to kick off the R30 Engine build Part 2, we finish assembling the head, prep the block and mating surface to accept the custom Copper head gasket and finally mate the head on our stainless O-ringed VR6 block.
As always thank you for watching and leave us your thoughts in the comments below.
-MMS
Instagram: @MalakaMotorSports
www.instagram....
Mailing:
MALAKA MOTORSPORTS
830 EAST PALMDALE BLVD #281
PALMDALE, CA 93550

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 63

@jamest5149 2 года назад

Just a suggestion… when using sealer like this on cam caps and on head gaskets etc, you only need the thinnest layer you can, it needs to be complete (no gaps) to seal but almost see through… in this case it really is less is more. When you clamp the bearing cap or head 95% of the sealer will be displaced and will end up in the oil and water galleries etc just where you don’t want it. 👍

@MalakaMotorSports 2 года назад

Noted, we thought we applied a decent amount per the advice given from some big power engine builders, but always great to hear feedback on how we can do it better, maybe we were a bit liberal with the seal. We will def keep an eye out in the future ❤️🙏

@risingstar1309 2 года назад

That’s a nice tip^ the cam caps for example need the thinnest tiny little layer. Juuuust enough to fill any tiny imperfections that the rubber/flexible material can’t go into

@steveswain4646 2 года назад

That silver block rocks

@samuelnelson6960 2 года назад

I gotta say, I think my favorite part of these videos is Stav's relentless 24v slander.

@MalakaMotorSports 2 года назад

It’s not slander if it’s true lol -stav

@TheObersalzburg 2 года назад

When George said we have it torqued to 25 ft lb , and Stav said that's good enough for this engine, I laughed out loud.

@razerone49 2 года назад

“Sounds like Stav’s uhh…”😂 I see you, George👀

@bendayho3k3 2 года назад

No suggestions here just enjoying the build. Nice to have you both back, STAV seems a little lost without George, lol. Keep up the awesome work.

@MalakaMotorSports 2 года назад

A team always works best together, thank you for the kind words 💪💪

@AudiophileTubes 2 года назад

Can't wait until you start drag racing your cars again!

@rickyzapf112 2 года назад

If you plan on revving high (which i know you are😂)Look into lifter shims, I bought them for my 3.2l head…basically they are small washers that go in the lifter bore and space the lifter up higher so if/when a lifter collapses at high rpm it wont separate from the rocker. I believe Ferrea makes them.

@bladejames8208 2 года назад

George, Stav, You guys are making me want to pick up a MK1 or MK2 Audi TT 3.2 , build and twin turbocharg, or single large turbo. I had a TT225 I bought new in 06. Had Turbo upgraded, all bolt on supporting mods, custom tuned. It was putting down 485HP, 465TQ , it was quick for the time, no problem beating Z06 Corvettes and so many other vehicles. You have me wanting to relive that fast go-cart of a car. This time turned up to 800-1,200 HP with the 3.2 V6.

@MalakaMotorSports 2 года назад

Put a 12v in it 12 valves never loose -stav

@582ChevelleSS 2 года назад

Loved the video and details. Keep up the awesome work and build ... can't wait to see this thing put down some passes.

@j.m.5995 2 года назад

I picked up two ultrasonic cleaners (3L and 30L) a while back and have to say that they re an absolute game changer when it comes to working on my car and it's engine and transmission.

@MalakaMotorSports 2 года назад

Agreed 1000000%

@jessevasquez2774 2 года назад

Can’t wait for that finish Malaka guys 🙌🏻

@gregs90quattrocoupe 2 года назад

Try MEK, it is better than Acetone, for cleaning. We used to use this for prep for urethane paint, on bare steel, in power plants. Nice work. It is always good to learn to do the job yourself.

@MalakaMotorSports 2 года назад

Will definitely look into MEK, appreciate the recommendation 💪💪💪

@gregs90quattrocoupe 2 года назад

@@MalakaMotorSports Nasty stuff. Wear gloves and masks.

@Smithsgaragevw 2 года назад

MEK is Good stuff but don’t breathe it in or get it on you it’s savage

@Alkivar 2 года назад

MEK is stronger than acetone, but acetone removes more types of contaminents. We used to use MEK at work for cleaning printer ink. shit will clean damn near anything off.

@matthewsafranek5476 2 года назад

Stoked to see this stuff! Keep it up, Malakas!

@Boaters_hub 2 года назад

Hey you, Get out of my garage! LOL! I love the smack talking 👍

@samuelrodriguez1324 2 года назад

This thing is gonna be re-donk-ulious.....

@tamikomuschette4541 2 года назад

Did George call the head bolts telephone poles? 🤣😂🤣😂🤣😂🤣

@MalakaMotorSports 2 года назад

Yuuuuuuuge 😂

@abubakerkhan7455 2 года назад

Love these videos. Can't wait for the next video

@BEYTEK Год назад

im learningggg for the rx7

@s4ybye594 2 года назад

Love seeing that R30 come together!

@MalakaMotorSports 2 года назад

Thank you !!! Learning with every step forward on this journey 🙏

@bladejames8208 2 года назад

George, where is your Rolex flex showing your steering wheel? 🤣🤣. Bro tat was funny.

@MalakaMotorSports 2 года назад

😂

@jamest5149 2 года назад

Keep up the good work and all the detail 👍

@MalakaMotorSports 2 года назад

Thank you very much sir

@РавшанШафигуллин-л4ш 2 года назад

Vr6 👍

@Smithsgaragevw 2 года назад

Are you going to run vvt? Been planning my r30 build and seen vvt deletes are available but can’t find much info. Love the vids. Off work with cvid pretty much watched them all now haha 👌

@MalakaMotorSports 2 года назад

We have vvt wired in and installed currently. We will be running vvt but may switch down the line to see back and forth testing and see if there are benefits on drag cars.

@rolly5009 2 года назад

Engine looking sweet - I like how it looks minty fresh in sliver, is the block stock or is it billet ? Greetings from the UK 👌🏼

@MalakaMotorSports 2 года назад

Right now it’s painted silver. After we explore what a cast vr6 block can do we will look into billet.

@holdingboost2024 Год назад

Love it! Just did this today with my 1.8T! Have you tried copper spraying the Head Gasket?

@trondaas9685 2 года назад

Hi. Found this build a couple of days ago, exciting to see the different solutions. A question, do you have the part numbers on the long and the short 1/2" ARP head studs ?

@MalakaMotorSports 2 года назад

We got the stud kit from speed density Motorsports. They make this kit I believe it’s around $525

@trondaas9685 2 года назад

@@MalakaMotorSports Thank you for the tip, will be in touch with them !

@maher8880 2 года назад

You have to empty out the lifer before you install it for the cames to sit comfortably

@MalakaMotorSports 2 года назад

We have always had hydraulic fully filled not emptied. So on start up we don’t damage and have to bleed out the lifters. Slightly harder but doable. If we have issue we will try your way

@garygarcia1571 2 года назад

Stav what is going on with your 12 valve? I have my 12 valve 3.2 in the car.Gary G.

@MalakaMotorSports 2 года назад

12v 3.2 sounds awesome Currently waiting on some parts once the vrs3 is sorted we will worry about my B5 and get back into revamping my baby. Lol

@scottyoungblood9715 Год назад

You can't aneal the copper head gasket before assembly?

@MalakaMotorSports Год назад

Comes already annealed 🤘

@veejay120793 7 месяцев назад

What duration cams did you go with?

@elielsandunguero 2 года назад

Stock cams?

@oliverjantz1108 2 года назад

So this is a 2.8 24 valve vr bored out to 3.0 correct?

@MalakaMotorSports 2 года назад

3.2 destroked to 3.0 💪

@vagracingcar 5 месяцев назад

where to buy head bolt strut

@enviousvdub 2 года назад

Need more stav and less george. Stav is a beast

@MalakaMotorSports 2 года назад

I’ve been telling george but he simply does not believe me lol -stav

@gideonlambrechts2113 2 года назад

May I request your old motor for my Q5🙏

@MalakaMotorSports 2 года назад

No touchy!!! Lol 😂.

@pavlodrabott3927 2 года назад

We wanna see the Stavs 12 valve build and his videos are more interesting to watch…

@MalakaMotorSports 2 года назад

Hahaha thank you for the support we got some stuff coming for stavs car.

@pavlodrabott3927 2 года назад

Thanks G, rs3vr is good stuff but most of us are single or divorced guys going thru mid life crisis that cant afford a lambo so we build an affordable vrt, best sounding engine hands down, dont matter 12v or 24v, 12v is just cheaper.