Random alarm! - Land Rover Freelander 2 / LR2 

This video is amazing! Alarm going off past 10pm at night and after some frantic searching, this was the solution I needed. With a torch, pliers and a clip I got it done and the neighbours and our house can sleep. Thank you so much for this detailed video!!!!

I can’t thank you enough for this, you saved me from embarrassment and insomnia! Thank you! 🙏🏽

Nice tip, thank you. Definitely a good temporary solution especially if you are on vacation and you need to lock the car. Thanks again.

Go to 8:05 guys, switch plug removal. Thanks for the vid, it is very helpful, my one started playing few months ago but it's getting more often and Ive noticed "bonnet open" light on the dashboard so I thought it's the switch causing this. Thanks! BTW, I like your washer fluid cap, no more mess, good stuff! 👍😊

If you want a really quick fix that takes two minutes just bear the wires before they go into the switch and twist them together. . The last two nights have been the first nights I've been able to have my car locked in silence, it's lovely😊

ive had my LR32 for about 3 months now and its only recently i realised that it was definitely the bonnet that was the problem. so thank you for the advice and i will get out and do the deed in a few hours.......

Thank you so much. I did this this morning. Only thing was, I had to degrease the plug to get the tape to stick. Little bit of copper electrical wire did the trick. 👍

Excellent fix, wheres the part 2 that so many comments promised! I want to see how easy it is to do a replacement before i give in and ask the garage!

Just used this quick fix during my lunch break. it really does only take two minutes. Especially if you have slim hands and not Homer Simpson fingers like me. Another great video and well explained. Keep it up Beavis Pits!

Thank you so much!!!!! Worked great. I truly appreciate you taking the time to record this video. 😊

so i know i have already posted but i just wanted to say a big massive thank you. its taken awhile because I'd been way too busy since 6 days back (thought it had been longer to be honest). so anyway, just got round to doing as you suggested and it works a treat. locked the car with the hood up and no alarm. 3 sodding months of searching the net trying to find the solution (or sell the car) and now its done. of course, if the alarm goes off again............. Kidding, you're a star buddy

My lr2 does this all the time it's a pain in the arse. Cheers for another good vid.

Great video. Solved problem to bonnet signal that said bonnet open. Easy fix .I have now ordered new part. Will figure how to fit it without taking the bumpers off. It maybe a bit fiddly but I determined to solve the problem without a large gararge bill Thanks again.Graham

Thanks so much for this. I’ve sorted my alarm issue out now. Cheers !!

Great video thank you. For the love of God why would a securely closed bonnet need to be alarmed?..? Is someone gonna steal your engine overnight? 😂

Just so people are aware, it's very easy to remove the sensor itself, pop the driver side Headlight out (2 10mm bolts and a push catch at the rear) Headlight out you can see the plastic sensor under the lastch, small flat head screwdriver to remove the sensor and a replacement is £15

Yup. Serious commitment dude. And taaalk soooo sloooowly. Even at x2. No hurry!

😂schön dank für die Tips 👍👍

Thank you. I found this extremely useful and very well explained. Subscribed!

you're a legend, was driving me insane 👍

Excellent, worked first time 👍

Cheers mate for the advice thanks

Is there a ultrasonic sensor in the car

Great vid! Thank you

To replace catch and switch…. The original is a two part, catch and switch. No longer available, so buy a replacement catch/switch, £15 to £30. Lift bonnet and remove RHS headlamp unit, 2 10mm screws + plastic latch, leave to one side Remove bonnet slam panel screws (across the top/front). 4 10mm screws this will allow the panel to flex maybe 75 mm Reach through the headlamp aperture and behind the slam panel and remove catch assembly 2 10mm screws. you have about 75mm of working space + panel flex Ease the catch assembly forward into the space and remove the electrical plug, pliers, screwdriver, cursing Remove the catch release cable from its clips behind the slam panel to give working slack Ease the catch assembly with cable attached up through the gap behind the slam panel and then work on the catch assembly on top of the slam panel Remove the cable from the catch assembly, lever it with a screwdriver, don’t damage the rubber grommets “Close” the new catch assembly by pressing the catch with the bar of a screwdriver Insert the catch cable into the new catch assembly, test that the bonnet release cable now opens the new catch Ease the new assembly back down past the gap behind the slam panel and re-seat the catch cable in its clips Re-attach the catch wiring plug to the new assembly, check the dashboard for “bonnet open” warning Re-attach the new catch assembly to the bulkhead, 2 10mm screws. Re-check functionality without lowering bonnet Re-attach the headlamp, 2 10mm screws Wash hands

At the beginning I thought I'd accidentally opened a Mark Felton video!

I have code B112C-87 Interior Motion Sensor , I disconnected the sensor but the code still shows. Could it be the bonnet catch generating this code?

Fuck yeah..! Been battling for 2 years to find that stupid sensor. Just bridged it out now. I thank you with all my heart for this video. Btw..its on the same side..South Africa.. 🙏🙏🙏🙏🙏

Is there any chance you could do a short or long video about the scuttle drain why it is so high at its sides and the drain down the wheel arch, because I am confused why it is funnel shaped and stand up about 1-2 inches?? my concern is water having to get that deep to drain??? or am I wrong 🙂

Hi everyone just done this to my freelander 2, looked like the person before me tried to do this. If the alarm still goes off in the night after doing this, what else could it be, please ? I have some neighbours who aren't happy about the alarms going off 🙃 😅

Great tip, thanks!

Hi, thank you for this! I've had this exact issue for so long. Neighbours hate me (internally) 🤣. Do we have part 2 coming soon? I'd like to ideally replace the part or clean it if not damaged. Cheers

Hi I have my LR2 and got problem with my door lock alarm everytime I close the door I need to close it hard so the alarm won’t go off. How can I remove the alarm if one of the door is not properly close? Thank you in advance

Thanks for the video. Will there be a part 2? 😁

Beavis Pits, do you have part 2 - how to change it ?

I cant find part2 😢

One way is to not press the panic button which I mistaken for the hazards.