Absimma AT1BL is my Truggy, used on tarmac streets and grass mostly, currently the rears are pretty worn and glued to the wheels, I believe the centre hub is 12mm its a 1/10 scale vehicle anyone with ideas what tired to put on it as to replace,
I'm just trying to find something for my revo. I'm torn between badlands, mashers, or trenchers. I wanted something that will hook up well on all conditions but mostly grass.
I wish proline had a slick tire for 1/10 scale cars. I’ve been looking everywhere and I haven’t found a high quality tire for 1/10 cars. I just want a slick tire that’s 2.5” in height and fit a 1.9” rim
What type of tyres come on a WLTOYS 124018/124019? Looks like tyres for sand? Or will they do well in grass too,m I'm wanting tyres that go on grass ie. Knobbie tyre.
What rim and tires would you recommend on my Traxxas Slash 4x4 vxl. Currently looking at the belted pro-line trenchers 2.8 any suggestions? Thx for the vids
@@Rcstreetshop thx. Just recently put sway arms on to help with roll overs especially with running 3s. This will help with that as well? And do you have a vid on slash upgrades or 17mm upgrade
Foam is popular option (or should I say the only option) if you go above 70Mph...as it would not balloon as rubber tires...Basically foam gives more grip on certain surfaces, but it also accumulates dirt as a magnet....and sometimes instead of providing more grip it does the opposite
i have a 2wd brushed traxxas stampede which i use off road (dirt, rocks, thin layers of sand, grass, etc.) any suggestions for the front and back wheels + tires?
What is a good tire for my kids to use on their traxxas slash 2wd. They play on some dirt but a minority of their time if spent doing skid turns on the street. They have the standard traxxas slash tire but the knobs hook in the street and the truck flip up ALOT. would love you suggestions.
There is no universal tire for both street and dirt. For street you need slick street tire for dirt you need knobs for grip. Maybe try lowering your suspension first or even switching to LCG chassis.
Which primes would you recommend for a 2wd brushless rustler? I like the smaller 2.2 wheels so I'm torn between the rear buggy tires or the 2.2 truck tires. I mainly like speed runs and sliding
Buggy tires/wheels generally speaking are better tires then 2.2 truck tires. You should check offset and hub though, as most buggy tires are on 17mm hub.
Thanks for the reply I planned on getting 2.2 rpm revolver rims that are made for the front of the rustler on both axles since I put the wide rpm arms on the front to run the same offset all around
It depends, but normally we recommend to avoid extreme compounds (ex. super soft, super hard etc) unless you know what you are doing. Clay would probably fit you better, but again generally speaking it is hard/impossible to suggest over the internet, since there are a lot variables.
RC Street Shop I honestly don't know the scale or shaft/hub configuration. I'm pretty new to rc and there is no literature on the car. I have a traxxas raptor and the lug nut tool fits the nuts on the car rims but that's where it ends. the car has shafts only with no bearings on front and rear has bearings inside the axle from what I get out if it
It depends on the carpet and tire manufacturer...ex. with Proline it is going to be Prism or Pyramid. You need to check with your local track they will let you know what works the best
umm im pretty sure its not a smart idea to run 4 pattle tires on any 4x4....lets really think about...because im thinking were missing something here...oh yeah STEERING...
Literally the whole point of 4x4 is steering, a typical truck drivetrain only drives the rear set or push where the "turning front" have no grip by making them drive allows them to grip and pull out in a direction. Paddles help this pulling out of sand in that direction.
