Rear Wheel Removal and Refit KTM Duke 390, 125, 200, 250

Подписаться 25 тыс.

Просмотров 17 тыс.

50% 1

Simple steps to remove the rear wheel, check the bearing and refit the rear wheel on the small KTM Duke 390, 125, 200,250.
This is a basic step to allow servicing and to change the rear sprocket
Instagram: / moto_mirius
Subscribe to keep up to date with the regular content: bit.ly/2UWwY90
___
Some links may earn me a small payment - but cost you nothing
Links to Where I Purchase Parts:
eBay: ebay.to/2Io2l6L
Amazon: amzn.to/2KvMiFA
___
2017 KTM Duke 390 Parts List:
- Power/ Sound
Akrapovic Slip On Exhaust KTM/RC 125 390: bit.ly/MotoMiriusKTMAkrapovic
Akrapovič Exhaust Grommet: bit.ly/AkrapovičExhaustGrommet
Exhaust baffles: www.pipewerx.co.uk/webshop/ac...
Decat Pipe Leovince Duke 390 2017 - 2019: bit.ly/MotoMiriusLeovinceCatDe...
Arrow Cat only Delete pipe: bit.ly/ArrowDeCatLinkPipe
Stunt/ Protection
Rok Bagoros Two Finger Stunt Clutch Lever: bit.ly/MotoMiriusStuntClutchLever
Magura X-Line Handlebar: bit.ly/MotoMiriusRokBagorosHan...
Rok Bagoros Adjustable Crash Cage: bit.ly/MotoMiriusRBAdjustableC...
Rear Sprocket 56 Teeth: bit.ly/MotoMirius56tStuntSprocket
Rear Sprocket 50 Teeth: bit.ly/MotoMirius50tStuntSprocket
O-Ring Chain 520 SRO6 120 Links: bit.ly/MotoMiriusORing520Chain
Galfer Wave Front Disk DF940CW
Rok Bagoros Front Freestyle Crash Pegs: bit.ly/MotoMiriusRBFreestyleFr...
KTM Powerparts Engine Cage
Service
R&G Paddock Stand Slider: ebay.to/2UgX1Dp
KTM oil Change Kit: bit.ly/MotoMiriusKTM390OilChan...
K&N Oil Filter: bit.ly/MotoMiriusKNOilFilterKT...
Style
KTM Powerparts Bar Ends: ebay.to/2Xcfv9U
KTM Powerparts USB Power Outlet Kit: bit.ly/KTMUSBPowerKit
___
Playlist 390 KTM Duke: bit.ly/2VGE3I0
____
Follow me here:
Instagram: / moto_mirius
Facebook: / motomirius
Website: www.moto.mirius.co.uk
___
Music provided by Epidemic Sound: www.epidemicsound.com/referra...
___
Logo: bit.ly/2Zau67P
#RokONSquad #MotoMirius #KTM390
moto mirius,RokONSquad,rok bagoros parts,ktm 390,ktm motorcycle,ktm,
ktm duke 390,390 KTM Duke,ktm duke,duke 390,390 duke,duke 390 mods, 390 duke mods, duke 390 modified
2017 ktm duke 390,ktm duke 390 2017,2017 duke 390,390 duke 2017,duke 390 2017,2017 ktm duke,2017 duke 390 modified,2017 duke 390 mods,
2018 ktm duke 390,ktm duke 390 2018,2018 duke 390,390 duke 2018,duke 390 2018,2018 ktm duke,2018 duke 390 modified,2018 duke 390 mods,
2019 ktm duke 390,ktm duke 390 2019,2019 duke 390,390 duke 2019,duke 390 2019,2019 ktm duke,2019 duke 390 modified,2019 duke 390 mods,
2020 ktm duke 390,ktm duke 390 2020,2020 duke 390,390 duke 2020,duke 390 2020,2020 ktm duke,2020 duke 390 modified,2020 duke 390 mods,
ktm rc 390,ktm rc,ktm,rc 390,390 rc,rc 390 mods, 390 KTM rc
2017 ktm rc 390,2017 ktm rc,2017 ktm,2017 rc 390,2017 390 rc,2017 rc 390 mods,2017 390 KTM rc,ktm rc 390 2017,ktm rc 2017,rc 390 2017,390 rc 2017,rc 390 mods 2017, 390 KTM rc 2017
ktm duke 125,125 KTM Duke,duke 125,125 duke,duke 125 mods, 125 duke mods, duke 125 modified
ktm duke 250,250 KTM Duke,duke 250,250 duke,duke 250 mods, 250 duke mods, duke 250 modified
ktm duke 200,200 KTM Duke,duke 200,200 duke,duke 200 mods, 200 duke mods, duke 200 modified

Авто/Мото

Опубликовано:

6 янв 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 70

@sohebr6540 2 года назад

Really appreciate your videos. Spot on explanation and learn a lot. Greetings from Mauritius 🇲🇺

@MotoMirius 2 года назад

Awesome, thank you!

@Paulie3051 11 месяцев назад

Your videos are on point. I learn allot from watching. And I really appreciate that you are very thorough. I have learned allot on how to do my own on my bike.

@MotoMirius 11 месяцев назад

Great to hear!

@HellGatefr2 Год назад

Thank you for this video, I got a flat tire and needed to dismount the wheel, it was very useful to get your instructions ! Personally I didn't need to tinker with the chain tension setting at all

@MotoMirius Год назад

Thanks and great job!

@Rainer_Zufall_ 2 года назад

Nice helpful Video. Thx a lot and greetings from good old germany

@MotoMirius 2 года назад

Glad it was helpful! And greetings back to good old Germany!

@mjacobim 2 года назад

Greetings from India and land of KTM's partner. Expecting more maintenance videos like this :)

@MotoMirius 2 года назад

I've recently reorganised my KTM videos so the maintenance videos are now all in the same playlist as they were getting hard to find in the modification videos. But there are still more to come!

@markgilgorobat5296 2 года назад

Kudos! Awesome! Very helpful vlog. Thanks

@MotoMirius 2 года назад

Glad it was helpful!

@hectorlavoe6663 2 года назад

Thanks for the vídeos very useful the sound effects can be better thanks a lot for the videos🔥

@MotoMirius 2 года назад

Thanks. What about the sound don't you like?

@callumboothroyd3766 2 года назад

Very well explained David, will be using once I need to change my sprockets and discs!

@MotoMirius 2 года назад

Thanks, good luck with that. I'm thinking of getting another set of road oriented sprockets to create an alternative build.

@callumboothroyd3766 2 года назад

@@MotoMirius you have the 50t stunt sprocket if I remember correctly? I was going to get that but I think I'm just gonna stick with stock gearing.

@MotoMirius 2 года назад

@@callumboothroyd3766 I have a 48 tooth, but close. Gearing is what works for you, so thats fine

@Keno.H Год назад

Very helpfull Video 👍✌️

@MotoMirius Год назад

Glad it was helpful!

@xSoYeahThatHappenedx 5 месяцев назад

Great video! The only thing missing are the socket and wrench sizes. Thank you for help! Now I can get my wheels off for new tires. I haven't ridden since I got a flat in August.

@MotoMirius 5 месяцев назад

Glad I could help and well done! Sometimes I do put the socket and wrench sizes on. There are several reasons that I don't as a rule, but the most important is that the cheapest way to buy spanners and sockets is as a set, and I've found that putting the sizes on leads people to buying them individually - and I'm still using the same spanner set I bought nearly forty years ago. If you need to know a spanner or socket size because you are missing one that fits, just measure across the flats of the nut.

@Rafriasduc Год назад

Hello, please the specs of the tools uses example size wrench etc ..

@Asousaaa 2 года назад

Hi David, greetings from Brazil! Your content ia absolutely rich and I am learning a lot. Thanks for share your knowledge. I have a question regarding the TFT display. I didn’t found any video related that and I believe that you faced the same issue that most of us: fog in the display. Do you have any tips to solve or minimize that? Also, could you prepare a content regarding that? Thanks

@MotoMirius 2 года назад

Thanks and hello to Brazil. Fogging in the TFT is not unique to this bike or even KTM. The TFT is not airtight so water can enter even as moisture in the air on a damp day. I don't think KTM have solved this even with several years of trying. I find there is can be a little water after riding in the rain, but it dries out when the weather improves. I have added it to my list. Thanks

@ahmedk7815 2 года назад

Hi David. Genuinely blessed to have come across your channel. I recently got a duke 390 and I've learnt so much from your tutorials and videos. Keep it up 👌 I have a quick question. What size is the nut you have to torque to 98nm? I'm trying to order a torque wrench and I want to make sure I get the set with the correct socket for it. Thanks!

@MotoMirius 2 года назад

Thanks, much appreciated. It's a 22mm nut.

@maxthebeast1311 2 года назад

i have a queation do you know how to remove the error "abs failure" it popped up when i unplugged the display and plugged it back in and now its there

@MotoMirius 2 года назад

Hi, it's an odd error to have pop up if all you have done is unplug the display. Could you have pulled the harness and disturbed another plug? Otherwise you might need to visit the dealer to have the code reset. Good luck with that.

@Subkeys Год назад

I successfully taken off the rear wheel however whenever I attempted to put the wheel back on I cannot fully tighten the axel bolt because it tightens the rear wheel to the point it will not spin freely also makes the rear breaks feel funny

@MotoMirius Год назад

Yes, I have had that happen. You just need to make sure that everything is properly in place with the spacers in the right places and then it will tighten up properly.

@hectorlavoe6663 2 года назад

Legend

@MotoMirius 2 года назад

Thanks

@osamaaijaz4055 2 года назад

Hey David, Best wishes for the new year! Had few questions: 1. What's the best way to align the rear wheel to avoid any wear & tear of the tyre? 2. Can I use silicon grease instead of lithium?

@MotoMirius 2 года назад

Hi and thanks. There are a number of ways to align the chain - KTM recommend using the marks provided for this purpose on the rear axle. Lithium grease is designed for lubcricating steel and mechanical parts. Silicon is for rubber and plastic - it does not have the mechanical strength for steel parts. Lithium is not ideal for plastic.

@osamaaijaz4055 2 года назад

@@MotoMirius Noted. Thanks!

@vidsupercharged1622 2 года назад

Seals that go on the axle come in contact with road grime, oil and hazardous chemicals. They're generally made of nitrile . Same with fork seals as they see oils and sometimes fuel. They're nitrile too. Lithium grease goes good with nitrile and neoprene. Silicone is generally used to natural rubber. We don't use natural rubber seals anymore because they would go bad within very few months. Here's my two cents! Cheers.

@vishnucr1735 Год назад

Hello David, I have a 2015 RC 390 and it ran 16000KMs, Chain and sprocket not changed yet. recently when rotating the rear wheel, the chain clatters hard on the swing arm, i have tried to matched the spacer alignment to almost identical, yet there is a wavy pattern in chain motion. The chain gets really tight on part of rotation then comes back to normal. Changed the bearing recently, yet its same. Any idea ?

@MotoMirius Год назад

Sounds like it's time for a new chain. It's normal for old chains to have stretch in some parts and tighter spots elsewhere. Check also that the rear sprocket is not bent - but if changing the chain, sprockets should be changed at the same time.

@vishnucr1735 Год назад

@@MotoMirius chain and sprockets is not worn out, but it did had some rust a while back.

@dimitriszafeiropoulos272 2 года назад

hello moto mirius!!!! Can u tell me why a ktm 250 duke sometimes downshifting at low rpm stalls (only when the clutch is kept pressed)? Thank u very much

@MotoMirius 2 года назад

In my experience this happens when the clutch lever isn't pulled in enough (or not adjusted for clutch wear). The engine is designed to rev very quickly and also engine brake very quickly - Ready To Race. The problem with race oriented engines is that they stall very easily and are very lumpy at low revs. There are two solutions, which apply to all race engines - make sure that you pull the clutch in enough and don't run the engine at low revs - it isn't designed for it. Ever see a supercar in slow traffic? They don't flow with the traffic, they rev the engine and accelerate then brake heavily, then repeat. I have often stalled the engine under heavy braking or when trying to pull away at low revs.

@dimitriszafeiropoulos272 2 года назад

@@MotoMirius i agree!!!! Thank you so much because some mechanics told me the bike is broken. keep up the good work!!!

@ItsThe675 Год назад

I'm following this video to take my tire off so I can bring it to the mechanic and get an inner patch done where a nail went through. When I put it back together and put new grease on everything, does it need to be lithium grease on all of the parts that I will be re greasing.?? I'm doi.g this on the RC390 not the Duke

@MotoMirius Год назад

Ah, the grease debate! Personally I use a general purpose grease for this, but lithium based greases are becoming more popular for general purpose use - check the description on the grease as some are more specialist.

@ItsThe675 Год назад

@Moto Mirius okayy I'll check them out. I'm bringing the tire to get an inner patch/ plug because of a nail (in my month old -300mi use tire 🤬). So while at the mechanic I'll ask them what they sell, or at least use

@alfredojurado3948 2 года назад

Hi David, i'm from México, your videos are very well explained all of them, i have a question what size it's your rear tire??

@MotoMirius 2 года назад

Hi Alfredo, thanks. I run a 150/60 on the rear

@ahmedk7815 2 года назад

@@MotoMirius Hi David. How do you find running a wider wheel? What are the pros, any cons?

@MotoMirius 2 года назад

@@ahmedk7815 A lot depends on tyre design, this one is quite flat with very short sidewalls so it gives a good contact patch. 150 is a typical stock tyre size.

@gy8132 Год назад

Excellent clip, your knowledge is impressive Mr D. Are you motorcycle mechanic or is working on bikes a hobby?

@MotoMirius Год назад

Thanks. It's just a hobby for me.

@gy8132 Год назад

@@MotoMirius keep up the excellent work, you have given me confidence before tackling same work on my Duke 390.

@user-jg8oj3ph5h Месяц назад

hello Just to clarify, did you lubricate a lithium lubricant with a temperature range of -30+120 degrees? self answer) manual indicates "Bike Grease 2000" as lubricant for these parts of the rear wheel. its range is -30 +120 degrees

@MotoMirius Месяц назад

The function of the grease here is to allow the parts to slide together without damaging the coatings and it helps to prevent corrosion. The rear wheel has bearings which do all of the work - there is no friction on the axle creating heat.

@user-jg8oj3ph5h Месяц назад

@@MotoMirius thank you!

@deepakp716 2 года назад

What's the size of the tier?

@MotoMirius 2 года назад

It's a 160

@gorkhekoreanschool6445 2 года назад

Hi I am from the country of Mt.Everest I wish if you make videos about ktm bike wiring and sensor issues

@MotoMirius 2 года назад

Hi, what wiring and sensor issues are you having? Being at high altitude changes the fuelling requirements and makes changes to the bikes such as exhausts much harder.

@gorkhekoreanschool6445 2 года назад

@@MotoMirius I mean like starting problem, missing problem, battery charging problem, no headlight etc with problem explanation, proper diagnosis process and solutions at all.actually am not having problem but being a mechanic we need to be updated regarding these current issues....anyways thanks for your kind reply

@MotoMirius 2 года назад

@@gorkhekoreanschool6445 OK thanks. I will give that somethought - some big topics there.

@borky1987 Год назад

Is that rear tire standard on the 390?

@MotoMirius Год назад

It is the stock tyre size yes. Different brands will sometimes have different profiles and different brands have been fitted as stock over the years. This is a Bridgestone.

@borky1987 Год назад

Could you fit a 170, 180 on it, or would it be to wide?

@MotoMirius Год назад

@@borky1987 160 is typically the biggest and user reports are that handling starts to get worse. Bigger than that and you risk it coming off the rim - assuming you can even get it on in the first place. I've heard of people fitting 170 but it's hard to know if they even ride the bike or just want something they can park up.

@springy-2112 2 года назад

Just like Tatro but without all the moaning ! mind you he's calmed down a bit since he's moved shop and doesn't have to deal with all the "dumb ass" customers 😅.. Good precise video David , peace and Love brother 👍🏻☮♥️

@MotoMirius 2 года назад

Cheers. Tatro always makes me laugh, but yeah I think he is happier without having to deal with people

@hrensburg007 Год назад

Why lithium and not calcium grease?

@MotoMirius Год назад

The purpose of the grease is mostly to prevent seizure and corrosion - it doesn't have to be a high performance grease - all the work is being done by the bearings.