Replace Front Wheel Hub and Bearing with Portable Press! - Toyota Camry - Easy How To

Подписаться 57 тыс.

Просмотров 105 тыс.

50% 1

No need for a high torque impact driver, 6 foot breaker bar or shop press to get out and install FWD bearings! I combined components of two kits (FWD Front Wheel Drive Bearing Adapters Puller Press Replacement Installer Removal Tool Kit - AND- a 10 Ton Hydraulic Knockout Punch Hole Driver Kit) to squeeze out old bearings and squeeze in new bearings in steering knuckles.
To squeezed out old bearings, I've been using my high torque impact wrench to torque twist the forcing screw nut. This places wear and tear on my impact wrench, makes a lot of noise and runs down the battery pack. Also, depending on the quality of the hub and bearing adapter kit, the forcing screw and nut may wear to to point where galling can ruin them.
So what did I do? I screwed in the forcing screw into the hydraulic cylinder and used one of the knockout punch threaded adapters to adjust the screw pull length. The hydraulic cylinder has about 1 inch of travel. After the bearing has moved 1 inch, I release then tension on the forcing screw, remove the slack using the punch adapter then continue pressing the bearing out.
The hub and bearing replacement was performed on a 1999 Toyota Camry.
If you'd like to make a donation to the channel, please follow the link below: paypal.me/Hard...
Parts & Specialty Tools:
GMB 770-0173 Wheel Bearing Hub Assembly
(Fits: 05 - 04 Avalon, 92 - 03 Camry & 99 - 03 Solara)
amzn.to/2JO20ft
Lisle 39510 30mm Axle Nut Socket
amzn.to/3lfQuYc
10 Ton 1/2" to 2" Hydraulic Knockout Punch Driver Tool Kit
amzn.to/3ZsCdvM
Front Wheel Bearing Adapter Puller Kit W/Grade 8 Drive Bolt
amzn.to/2Uvstio
Slide Hammer Puller Set:
amzn.to/2FazwI6
16 Inches Heavy Duty Snap-Ring Pliers:
amzn.to/36lZmFe
Milwaukee 2767-22 Fuel High Torque 1/2" Impact Wrench w/ Friction Ring Kit (This is the super high torque impact tool that generates over 1400 lbs of nut busting torque! A lot more than the one used in this video!)
amzn.to/2MzfKIW
Milwaukee 2767-20 M18 Fuel High Torque 1/2-Inch Impact Wrench with Friction Ring (if you have M18 battery packs - bare tool - no battery)
amzn.to/35kOBS9
Powered Impact Tool (not the one I used, but less expensive quality corded version):
amzn.to/2F57ldk
As an Amazon associate, I earn from qualifying purchases. Thank you for your support!
#wheelbearing #wheelbearingreplacement

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 288

@tomknud 2 года назад

Pretty cool. I think I might coat the bearing in grease before freezing to curb condensation directly onto the metal, though.

@hardlymovingpro 2 года назад

It'll all evaporate.

@Maestro-gh2ei 7 месяцев назад

This man is such an inspiration dude, i’m broke down on my luck and absolutely got fleeced purchasing my first car but watching his videos i’ve been able to fix so much and stay afloat.

@hardlymovingpro 7 месяцев назад

Good for you!

@nathanjohnson3790 Год назад

Wow!!! Most Creative manner to use a piece of equipment in a "Thinking Outside The Box" Way!! I Am Truly Impressed!! Great Job!!!!

@hardlymovingpro Год назад

Glad you liked it and thanks for the visit!

@terryzak1742 3 года назад

Brilliant on every level. Efficient, fast, and economical. The hydraulic kit costs 1/3 or so of a high-torque impact gun. Should be a great money maker for anyone who uses flat-rate or similar charges. Wonderful!!

@hardlymovingpro 3 года назад

Thanks! I also focused on off site portability and utilize the power features of a hydraulic shop press while keeping the steering knuckle on the car.

@on-site4094 3 года назад

The hydraulic pump make it a breeze 👍

@hardlymovingpro 3 года назад

I know. And I haven't seen ANYONE use this technique! It's simple.

@angelramirez7747 2 года назад

This is genius; I've been working hard unnecessarily pressing bearings in and out manually. Thanks for an awesome install!!

@hardlymovingpro 2 года назад

Thanks! Work smarter not harder!

@jjunderwood4095 Год назад

Make it easier on yourself. Take the whole spindle off and while the new bearings in the freezer, heat up the spindle with a propane torch. I've never pressed in bearings, they just fell right in.

@josefelix4152 3 года назад

Man i just went sand bought this hydraulic hole punch, because my hub tool screw got damaged because of continuously impacting it, this method saves my hands, my ears, my tools and my time.

@hardlymovingpro 3 года назад

You said it my brother!

@nathanl7795 Год назад

What you didn't mention is that if you have a abs sensor the bearing needs to go in a certain direction. The magnetic side needs to go in to where the abs sensor is. If you don't do it that way you will be pissed off cause you need to buy another bearing and start over.

@hardlymovingpro Год назад

With Honda's and BMWs yes ... Not Toyota. Toyota uses an abs ring for their sensors.

@nathanl7795 Год назад

@Hardly Moving Productions I understand but always good to mention this cause it's not the same on all of these.

@LR-dy5ck 2 года назад

Try and level some steering knuckles for a 20 ton shop press. If not secure you can damage the knuckle during removal or cockeye the bearing during installation very easily. This process greatly eliminates those damaging possibilities during removal and installation.

@hardlymovingpro 2 года назад

You're correct. You need more than a shop press to properly service pressed on bearings.

@brentmcgillis 9 месяцев назад

Wow, what an excellent video. Your camera person is so skilled at zooming in and showing the rest of us front bearing rookies how this is done properly. Thank you so much for your efforts making this video that shows in explicit detail the exact procedure for this Front Wheel drive font axle bearing replacement. Your video stands out against all others I have watched on this subject. I would have to recommend this video to anybody who has NOT done this procedure before because of the excellent content and great camera work, that leaves no part of this procedure as a grey area.👍👍

@hardlymovingpro 9 месяцев назад

Thanks for your critique! Most places remove the complete steering knuckle and press out the hub and bearing on a press machine which people don't own.

@J3yP1 2 года назад

Sorry to question your tool recommendations. But the astro kit has a 7/8-14 bolt and the punch kit has a 3/4-16 thread. It wont work unless you buy a 3/4-16 threaded rod n nut or buy the other kits other than the astro kit.

@hardlymovingpro 2 года назад

Good to know and thanks for sharing!

@oluwadarefavour9698 3 года назад

Amazing video👌👌 Does taking out the steering knuckle as a unit make the job harder, or you just decided to do the job on the vehicle?

@hardlymovingpro 3 года назад

Both. Easier to maneuver the knuckle while being attached to the lower control arm. Thanks for your post!

@majortom5190 3 года назад

Great video! I am deciding whether to do this job myself. You made it look so easy. Can you give me a list of all the tools that you used? I missed the part about removing the outer bearing race. Was this not necessary?

@hardlymovingpro 3 года назад

List of parts should be in the "show more" text description of this video. Don't understand your question. This whole purpose of the video is to show you how to remove the outer bearing race from the steering knuckle.

@xushnudbekismatov6332 3 года назад

Presni dastavka was buladimi

@hardlymovingpro 3 года назад

Shlangi nasos va adapter majburlash vintini tortadi

@Jigsaw_knows 3 года назад

Beware. Pump does not always match screw threads in large bolt. Once u figure it out its magnificent.

@hardlymovingpro 3 года назад

Agreed. Good idea to bring the forcing screw when shopping for a pump to make sure it fits.

@deagointhemix9798 Год назад

Wish I would have saw this

@Maestro-gh2ei 7 месяцев назад

Is it possible to overdo the process of pushing in the new bearing with the hydraulic press? Do i need to have a comprehensive understanding of where the bearing should be seated or can i just push it in until it feels right/can’t go in any further?

@hardlymovingpro 7 месяцев назад

When the snap ring grove is visable, you've pressed it in far enough.

@Maestro-gh2ei 7 месяцев назад

@@hardlymovingpro thank you 🙏

@Maestro-gh2ei 7 месяцев назад

@@hardlymovingpro do you offer 1 on 1 consultations? I’d be willing to pay for your expertise of course

@hardlymovingpro 7 месяцев назад

@@Maestro-gh2ei send email to hardlymoving@gmail.com

@Dhahdbjdnd Год назад

You should package bearing puller sleeve and plates with the pump and sell them as a kit!!!!! Money in the pockets!!! Shark tank!!!!

@hardlymovingpro Год назад

I did reach out to a few parts manufacturers about the idea but got no feedback or interest. Go figure.

@robertfrate9738 3 года назад

Hi, now this is absolutely what I call let the tools do the work let your experience work the tool, very informative and very nicely done the way it should be, the best install I’ve ever seen on the ground or a lift, the freezer trick I learned that years ago and it works very well, excellent quality video ty so much, Bob,

@hardlymovingpro 3 года назад

Glad it was helpful! Thanks!

@robertfrate9738 3 года назад

@@hardlymovingpro always a pleasure not many people take pride in their work anymore like we do, just my opinion,

@FlowtnWitWalden 2 года назад

Good stuff. What do you think about putting the bearing just in the refrigerator? I'm worried that when the frozen condensation melts after the bearing is installed it will be permanently rusted in place.

@hardlymovingpro 2 года назад

There won't be any rust.

@ManicMechanic007 3 года назад

Well done! Did you have to modify the hydraulic cylinder to fit the thread geometry of the forcing screw?

@hardlymovingpro 3 года назад

No ... Not at all. Seems like all these forcing screws in kits are of consistent diameter and thread pattern along with the hydraulic cylinders that accepts them.

@ManicMechanic007 3 года назад

That's great! Thanks for the response.

@hardlymovingpro 3 года назад

You bet!

@EdHotin 2 года назад

I’m curious to know where you got the long hex bolt from? I know it didn’t come with the hydraulic kit because I have the exact same kit and the bolt that comes with the hydraulic kit is a 3/4 inch 5 inch long stud bolt. I purchased the exact same hydraulic kit from Harbor Freight and the 3/4 stud bolt that comes with it is way too short to do what you did and the hex bolt that comes with the bearing adapter kit is a lot larger than 3/4 which is required to use the hydraulic kit. Thanks.

@hardlymovingpro 2 года назад

I used and cross purposed the bolt from the Hub Bearing Removal Tool kit (from the red kit in the picture). The threads from that long service bolt matches the thread pattern in the hydraulic press tool.

@bluemax229 Год назад

If my eyes did not deceive me, the steering knuckle on your car is exactly OPPOSITE of most vehicles (and videos) I have seen? Your bearing is removed and installed from the backside, assuming the extension with the two holes is for the strut?

@hardlymovingpro Год назад

That's correct with Toyota steering knuckle bearings. Some vehicles have front and rear snap rings where you decide direction of removal.

@MrSupernova111 2 года назад

Damn! That's amazing!! I wish I would have known about this before I went to replace my front wheel bearings! I used a 20 ton HF press but this seems much easier!! Thanks!!

@hardlymovingpro 2 года назад

Thanks! Here's what amazed me. I reached out to some parts manufacturers about making a kit with a hydraulic pump attachment. No one expressed an interested. Also, using a stand up press can be difficult without having a hub and bearing press kit. Getting that steering knuckle perpendicular to the press can be a bear.

@MrSupernova111 2 года назад

@@hardlymovingpro . Yep. It was real challenge doing this for the first time on a press. Great idea man! Cheers!

@hardlymovingpro 2 года назад

You bet!

@hobbyless4089 Год назад

I just did my front wheel bearing two days ago. I purchased a 20 ton press (got a real good deal), but it was very hard to support the knuckle. I ended up renting the tool from O'Reilly for $400. I'm still keeping the press, but I will also buy these two devices.

@sindriatlason6925 2 года назад

i bought my 15t hole puncher over 10 years ago for this same reasons. i have changed hundreds of bearings with it.

@hardlymovingpro 2 года назад

Good for you and thanks for sharing!

@sindriatlason6925 2 года назад

@@hardlymovingpro it is an excellent tool for bearings and bushings with metal outer sleeve. if you buy a bolt that has the same threads that go into the piston. then you can drill through it and tap the hole. now you can use smaller diameter bolt to go through bushings.

@ghe422 Год назад

Hello Sir, what is the size of the forcing screw that you attached to the hydraulic puller and did it come with the bearing puller set you used?

@hardlymovingpro Год назад

The forcing screw and bearing puller are provided as 1 kit. The length is consistent with most hub and bearing kits. The thread pattern can differ and have no way telling you.

@Maestro-gh2ei 7 месяцев назад

Can a bad wheel bearing on the drivers side cause my breaks to fail? Master cylinder was empty after this occured but no signs of leakage from any of the lines? Perhaps Master Cylinder inner seal failure, or it all drained into the brake booster? Brakes are fine when engine isn’t running, but they are soft and go to the floor when engine is running. Have to slam on them to get them to respond minimally if at all. This happened after jacking the car up on the driver’s side to tighten my lug nuts as I kept hearing a screeching sound that I now realize was a symptom of faulty wheel bearing

@hardlymovingpro 7 месяцев назад

You master cylinder seal is shot allowing brake fluid into the brake booster.

@rayw9602 5 месяцев назад

I just spent weekend with my teen son using breaker bar and it took forever. Are the threads for the bearing tool common standard with the punch tool, this was super clever, thank you so much for this, I’m encouraged continue with the other bearings that need replacement.

@hardlymovingpro 5 месяцев назад

Some bearing press kit's forcing screw have different thread patterns. A local machine shop could make you straight bar forcing screw.

@salvasiwan5453 Год назад

Toyota camry SV40 1994 front wheel bearing sample number

@hardlymovingpro Год назад

Go to rockauto.com

@bigdeal87 5 месяцев назад

The hydraulic press got M20 1.5 thread so will it fit the 7/8 14 rod thread ?

@hardlymovingpro 5 месяцев назад

Sorry ... Can't advise.

@CharlesLease-ei1ee Год назад

My thing is one more bolt and just put it on the press. He wouldn’t have to turn angle it just to get that in there or you could spend $400 for that the ram or just pay for our labor and have somebody press it out or do it by hand torch, hammer and freeze the bearing do it the old-school way

@hardlymovingpro Год назад

That's how I use to do it till I had too many of these jobs to do that needed fast turnover!

@leonidas9969 Год назад

Bought this pump from Amazon from the link idk why mine is different my press head doesn’t unscrew from the hose it’s one piece and the box is a metal one with styrofoam inside will buy this same one from harbor freight

@hardlymovingpro Год назад

Thanks for sharing!

@VeryPersian 3 года назад

Props for trying something new!

@petermuller161 2 месяца назад

Very nice, there are tools that do this specifically but you’re looking at thousands of dollars

@hardlymovingpro 2 месяца назад

That's right! Thousands of dollars! I got the idea to cross purpose my tools based on a German automotive tool kit.

@BeamRider100 7 месяцев назад

Looks like the screw from the bearing puller fitted the hole in the punch kit. Otherwise you would of had to root around for a suitable screw that fit the thread on the punch kit.

@hardlymovingpro 7 месяцев назад

That's correct! If the screw thread pattern doesn't match, you should be able to acquire one or have one made at a local machine shop.

@upallnight888 2 года назад

I have the same setup, but I ordered a high-strength threaded rod from McMaster Carr instead of using the forcing screw. I used the nut from the front bearing kit with the new threaded rod. First saw this used by this RU-vid DIYer. ru-vid.com

@hardlymovingpro 2 года назад

Thanks for sharing! Concept is still the same; that is, use hydraulics to force out pressed in bearings or force in new bearings.

@1mJustCurious 2 года назад

Would you be so kind to share the part number of the forcing screw and the washer that comes with it from McMaster Carr?

@garybuffington6021 11 месяцев назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-SkN1BbjU_s0.html

@garybuffington6021 11 месяцев назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-SkN1BbjU_s0.html@@1mJustCurious

@shehzadatif1 5 месяцев назад

Excellent video.. This is going to help us DIYers with bearing and hub removal without pain and noise.. way more efficient than impact gun. Appreciate you for being innovative and letting us know about knockout Punch driver..

@hardlymovingpro 5 месяцев назад

Thanks for sharing!

@tylerday4747 3 года назад

That’s a good idea putting the new bearing in the freezer. 👍

@hardlymovingpro 3 года назад

Definitely makes the squeeze into the knuckle happen with less pressure

@gavinsmartt6996 11 месяцев назад

Was the thread pitch and size of your draw bar from your other set the correct size and pitch to fit into the hydraulic pump?

@hardlymovingpro 11 месяцев назад

Yes. What you call the "draw bar" is commonly referred to as the "forcing screw". You may have to find a replacement forcing screw if the thread pattern on the screw doesn't match the hydraulic pump. A machine shop should be able to help you out if needed.

@mistacdawg6882 2 года назад

Autozone wants $499 to loan this thing

@hardlymovingpro 2 года назад

You can buy the hub/bearing tool set for under $80 on Amazon: amzn.to/3wiYC1v

@mistacdawg6882 2 года назад

@@hardlymovingpro Thank you, I got the one from Amazon and it worked perfectly! Just finished it today.

@johnblatney3140 Год назад

@Mista CDawg did you use the harbor freight punch kit with the 3/4-16 threaded ram and if so which wheel bearing kit do you have that has the same thread forcing screw as the ram... alot of people have asked him about this and he is not answering the question that is being asked... he just says take the bolt from your hub bearing kit to hf and see if it fits the hydraulic kit... we all have the same hydraulic kit ,we need to know which hub bearing kit, p/n and or link to buy the correct one to match up with our hydraulic kit. Thank you and I hope this can help me and many others

@505fastlife6 Год назад

@@johnblatney3140if you haven't figured it out the front wheel drive bearing adapter matches perfectly with hydraulic hole puncher both made by Pittsburgh at harbor freight.

@AutoDiag_ Год назад

Do you feel 10t is enough? I see there is also 15t version. Have you been in situation where 10t is not enough?

@hardlymovingpro Год назад

10t has worked for me. But if 15t is available, why not.

@angelmatos5987 3 года назад

Congratulations it a great idea use the hidraulic punch 👍

@hardlymovingpro 3 года назад

Thanks. Helps to stop wear on my impact driver.

@cyrusmoser1090 3 года назад

Nice! Love your videos.. Thank you sir

@hardlymovingpro 3 года назад

Glad you like them!

@stephenbay9564 3 года назад

Absolutely outstanding! Very creative! May I ask.....the bearing kit says the bolt that comes with it is 7/8" grade 8. I'd like to get that hydraulic kit you used, (and included a link for).....but it's obviously very important that the bolt in my kit fits this particular hydraulic kit's piston. Can you please tell me the exact size of the bolt that fit this hydraulic kit? Is it really a 7/8" bolt, with what? SAE or metric threads?

@hardlymovingpro 3 года назад

The hydraulic press kit was purchased at my local Harbor Freight store.

@johnblatney3140 Год назад

I have the same question. I have the Pittsburgh punch kit and the ram uses a 3/4 -16 unf fine thread forcing bolt. The wheel bearing set you have is different than the one you have a link to in Amazon and not just because the case is different. I need to get the wheel bearing replacement set that has that particular size forcing bolt. Where did you get your kit and can you please give us the link or description of your set as it Cleary has a bolt that threads into your Pittsburgh ram... any and as much info as you can provide would be much appreciated. Thank you!!!!!!

@bigdeal87 5 месяцев назад

Yeah wonder that too

@LamNguyen-hs2wo 8 месяцев назад

i did the same thing you did, works perfectly 👍

@hardlymovingpro 8 месяцев назад

Good to hear!

@marciliogoncalvesdasilva1019 2 года назад

Boa noite manda para mim o nome dessa ferramenta aí em português

@hardlymovingpro 2 года назад

Kit Extrator do Adaptador do Rolamento da Roda Dianteira. Use um tradutor de idiomas online e clique na descrição deste vídeo para ver as ferramentas que usei.

@tgw230 Год назад

How did you get the stuck inner race off of the hub? I didn’t see that part in the video

@hardlymovingpro Год назад

Watch this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-I4P3T-cb7rg.html

@عبدالمجيدناصر-ج7ض Год назад

مشاء الله

@roeuin 3 месяца назад

where did you get the hydraulic press from?

@hardlymovingpro 3 месяца назад

I cross purposed from a hydraulic knockout punch driver tool kit. They're used to cut / punch out large round holes in sheet metal. I provided a link to the kit in this video's description.

@Ed-de3ro 6 месяцев назад

Hi there, changing the wheel bearing by using a knockout pouch is a small way of thinking. Great video and thank you for sharing your genesis thinking. The size of the hydraulic pouch threads is M20-1.50mm. The wheel bearing set large bolt is 3/4"-16, thread pitch That’s a little too small to work correctly without damaging the bolt or hydraulic pouch threads.

@hardlymovingpro 6 месяцев назад

Thanks for watching! The wheel bearing (large bolt) is called a forcing screw. Believe if you go to your local machine shop they can provide you a non headed screw with the correct thread pitch. You can then screw on a nut on each end giving you more adjustment flexibility when attached to the press bearing adapter plates.

@johnblatney3140 Год назад

Hey man i really appreciate you showing this video. I have tried to communicate with almost 20 people selling the fwd hub bearing replacement kit and not 1 could either tell me the size and thread pitch of the main large forcing bolt that you show threading into the Pittsburgh hydraulic ram... could you please send me a link or anything that would guide me to the right kit that will work with the Pittsburgh set. Thank you very much in advance and i hope you can help me out!👊

@hardlymovingpro Год назад

Suggest you contact a local Tool & Die machine shop to get the size and pitch specs.

@johnblatney3140 Год назад

I know the specs of the bolt needed and yours has it. I need a new bearing replacement kit as well so do you mind giving me the info of yours and where to buy it? I have the Pittsburgh hole punch kit and now I just need the other kit to replicate what you have. I would greatly appreciate the info! 🙏Thank you in advance..

@johnblatney3140 Год назад

Hey buddy did you get my last message where did you get your bearing replacement kit and if you happen to have a link or a way for me to locate it I would really appreciate it. Thank you. Just let me know if you can or not 🙏

@horacewilliams4254 Год назад

Hi, where can i get that press tool? What name can i look for?

@hardlymovingpro Год назад

Tool details are in this video's text description.

@Heybat 11 месяцев назад

How did you remove that piece of old bearing from the wheel hub? You did not show that part

@hardlymovingpro 11 месяцев назад

If you're going to use your old hub, here's the video showing how to remove the stuck inner race: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-I4P3T-cb7rg.htmlsi=_0SgQm8MBlOq4Len

@Heybat 11 месяцев назад

@@hardlymovingpro thank you so much

@mikejr550 3 года назад

This is amazing! Thanks for sharing!

@hardlymovingpro 3 года назад

You bet!

@mrlyricsneo Год назад

from where i can get one of this portable press kit please ??

@hardlymovingpro Год назад

Tool links provided in this video's description area.

@mrlyricsneo Год назад

@@hardlymovingpro thank you

@nathanjohnson3790 Год назад

Also!! Sir!! You Most Differently Should have more subscribers on this one!! Outstanding!!!

@hardlymovingpro Год назад

Thank you so much 😀

@yessirskiii2615 2 года назад

Would this also work with a Volvo C30? The bearing is inside the hub and must be replaced together. Remove tool has plates that go behind the hub.

@hardlymovingpro 2 года назад

Should work with minor differences.

@stephenbay9564 3 года назад

PS - Please understand, that I want to buy that hydraulic kit right now, but I need to be sure it will accept the bolt in my bearing kit.....and that is why I ask about the size of the bolt in that kit, OK?

@hardlymovingpro 3 года назад

That was my concern before I bought the press kit. I recommend you take the bolt to your local Harbor Freight store and see if it'll screw into their press adapter. I'm sure the threads and diameter will match.

@leored79 6 месяцев назад

Cool, i have the 17t cylinder from Klann...highly recommended...

@hardlymovingpro 6 месяцев назад

Thanks for sharing!

@deagointhemix9798 Год назад

My long forcing screw from the press kit won’t screw into the hydraulic puller. Did u find another screw for this?Plus my cup stuck on the outside from my impact gun any ideas on how to get it off

@hardlymovingpro Год назад

Yes. I've learned that the thread pattern on some of these press kits won't match. You have to go to harbor freight tools where they have both kits to verify a match. Try light taps with a hammer to get off the cup.

@chrisboyd6032 Год назад

At 3:00 where did you get the threaded bolt that fits the hydraulic punch kit. The one that came with my hydraulic punch kit is short. The bolt from my bearing press kit is long enough but a courser thread than my hydraulic cylinder .it's a fine thread.

@hardlymovingpro Год назад

The "threaded bolt" or forcing screw came from the Hub and Bearing kit. The one I bought had a forcing screw with a thread pattern that matched the hydraulic pump. Try a local machine shop and see if they can order or make you one.

@ahmadghosheh3104 3 месяца назад

This is amazing. Got to get one

@hardlymovingpro 3 месяца назад

Cross purposing tools.

@dannysautorepair 2 года назад

Would the 10 ton tool work also to press out the bearing or does it have to be the 15 ton tool ?

@hardlymovingpro 2 года назад

10 ton should work.

@siucbset 3 года назад

Practical: Cool video, however, since you only have one lower nut left. Why not just remove it then take the knuckle to a press?

@hardlymovingpro 3 года назад

I could but the purpose of the video is to show convenience and portability while avoiding big, bulky equipment.

@jeanlawson9133 4 месяца назад

Smooth Brother

@hardlymovingpro 4 месяца назад

Appreciate that!

@toyotatundra0455 3 года назад

This is best idea in RU-vid. What the size and thread of the bolt in hydraulic knockout punch? I have the Astro Bearing Pressing kit. I'd like to use it to remove hub wheel in a 4WD 2004 Tundra. Before, I buy the kit from HF, I'd to know if I need a longer bolt. Thanks.

@hardlymovingpro 3 года назад

I went to harbor freight and the thread pattern in the punch kit's hydraulic adapter matched my press kit forcing screw.

@toyotatundra0455 3 года назад

@@hardlymovingpro Thanks. I hate to bother you. One more question, who makes your slide hammer kit?

@WILSONJ-tn9om 3 года назад

WOW!! Does autozone or O'Reillys part stores have them to rent out the hydraulic pump? Great work!!!

@hardlymovingpro 3 года назад

Thanks! Nope ... no tool rentals on both the bearing press adapter kit and hydraulic pump. The press adapter kit usually goes for around $70 and the hydraulic pump comes in a knockout pump kit for around $100. See the "show more" text description of this video for more details.

@kayrod57 3 года назад

Wow... you made it look so easy. Xan you help me solve my problem? I changed my bearing and hub but now I have a louder whirling sound at around 40 mph. I used to only have a humming sound barely noticeable. How can I troubleshoot my repair?

@hardlymovingpro 3 года назад

Hub may not be completely seated against the outer CV bearing cup. Try re-torquing the axle nut.

@ryang1589 2 года назад

No way I disagree with you I would rather wear out my impact gun instead of myself using a slide hammer

@hardlymovingpro 2 года назад

You can lead a horse to water, but ...

@oby-1607 Год назад

Wow, you are a thinking man. I have a 1998 Camry which I will never sell and this will help keep it alive.

@hardlymovingpro Год назад

Right on!

@fredguerra4917 7 месяцев назад

I see it looks to me the tool can also use my greenlee knockout punch in the same form. I just got to get the proper size adaptors. Thanks for the tip!

@hardlymovingpro 7 месяцев назад

You bet!

@samsonn25 Год назад

nice

@hardlymovingpro Год назад

Thanks!

@tomhale9863 3 года назад

Did you have to buy a long fine threaded bolt because the one that came in red box kit with all the amatory was coras thread

@hardlymovingpro 3 года назад

The "threaded bolt" is commonly referred to as a "forcing screw". Just take the screw out of the kit, bring it to the shop selling the hydraulic punch kit and see if the screw threads into the punch adapter.

@chumbucket1313 Год назад

So i am wondering if it wouldn't be easier to remove the whole piece take it to a shop press press the bearing and bolt it back on?

@hardlymovingpro Год назад

That's what I use to do. Problem was repair down time and time spent going back and forth to the machine shop.

@Dhahdbjdnd Год назад

I had the same idea doing the same thing. Now I don’t have to think on how to do it. You already figured it out.

@hardlymovingpro Год назад

There's a German tool company that sells a kit for close to $2,000 that does the same thing. That's where I got the idea.

@LamNguyen-hs2wo 8 месяцев назад

i did the same thing you did, works perfectly 👍

@hardlymovingpro 8 месяцев назад

Good for you and thanks for sharing!

@luiscardonapcardona5243 2 года назад

Hello my friend Where did you get the bolt from ? Thanks

@hardlymovingpro 2 года назад

I used the bolt (also called a forcing screw) from the bearing adapter kit. The bolt threads matched the hydraulic press tool.

@RohitPatel-et2cg 7 месяцев назад

What make is your bearing service kit and model number

@hardlymovingpro 7 месяцев назад

Links provided in video description

@RohitPatel-et2cg 7 месяцев назад

The kit on the link looks different from the one you have on your video. Will the bolt from the kit on the link screw on to the hydraulic punch

@RohitPatel-et2cg 7 месяцев назад

Will the Maddox kit from Harbor freight work with the hydraulic punch tool

@hardlymovingpro 7 месяцев назад

Check the fit at the store?

@douglascunningham1840 Год назад

Make sure the axel is snapped in into the transmission all the way or your wheels will rotate hard when in park.

@hardlymovingpro Год назад

Absolutely!

@wranefis 3 года назад

How do you when to stop pumping it in ??? Would it be easier to put the back o ring/lip and push it in front the front till it hit the o ring well till you be able to feel the resistance that it is hitting it ?

@hardlymovingpro 3 года назад

I've found visual inspection on the progress of the bearing movement to be the easiest. Also, with the bearing being frozen, it didn't take much pressure effort to pump the new bearing in the steering knuckle until I felt the back pressure indicating the bearing has reached the lip of the steering knuckle.

@Andre-tc1wj 3 года назад

Can you tell me the model number on both the hydraulic pump and bearing press kit. I ordered the press kit you have listed ( Blue) but the hydraulic pump I have looks to be the same company the forcing bolt in the press kit is a different size. The pliers u recommended worked great. Thanks again

@hardlymovingpro 3 года назад

I recommend you go to a local Harbor Freight near you with the bearing press kit's forcing screw. Then see if the forcing screw thread pattern matches the threads in the punch kit hydraulic adapter. Another thing you can do is replace the short forcing screw in the punch kit with one that's the same length in your bearing press kit. Go to your local machine shop and see if they can help you out finding a supplier.

@Andre-tc1wj 3 года назад

@@hardlymovingpro I purchased the hydraulic pump 56411 from Harbor Freight and the press kit from your list of tools. I will check around for a local shop. Was looking to purchase the hydraulic pump you suggested if it will work with the blue press kit you suggested. Do you know if that hydraulic pump works with the blue press suggested?

@jalixvarietytv7849 2 года назад

Thank you for uploading a nice video. More power💪🇺🇸

@hardlymovingpro 2 года назад

Glad you enjoyed it!

@mannyclemente7159 3 года назад

Hey boss, is it required to do a front wheel alignment after this type of job?

@hardlymovingpro 3 года назад

Most of the time ... No. If there's steering wheel pull to one side while driving, then yes.

@RM-ub1xd Год назад

So you push the old bearing out towards the engine right and install back from the same side?

@hardlymovingpro Год назад

That's correct. Can only go in or out in one direction.

@deeeyewhy5949 Год назад

Is this the same process for the rx330? The part looks identical for the Camry from years 99-06 maybe even beyond that from what I can tell in pictures at least.

@hardlymovingpro Год назад

Yes but the bearing will be different

@deeeyewhy5949 Год назад

@@hardlymovingpro Are the bearings for the 4cyl and 6cyl Camry different? From what I’ve read the bearings should be the same for camrys from 04-09 and then many after that should also have the same bearing and hub as the rx330. Only asking because Someone near me is selling a set for cheap and they bought it for on 06 Camry but idk yet if it was 4 or 6cyl variant

@deeeyewhy5949 Год назад

Sorry one more question. Just How much torque you think I’ll need to pull a bearing? My ryobi p262 is a beast 500 easy probably get 600 lbs/ft if I jam on it at high for 15 seconds with a full 6ah pack. Dropped the thing in a bucket of atf during the engine swap and it didn’t skip a beat! (Have seen a Milwaukee dunked in water while spinning so I wasn’t too surprised) but I’m wondering if I need something that gets into the 800-1000 range?

@thomaslevine6120 3 года назад

the link for the "Front Wheel Bearing Adapter Puller Kit" (comes in a blue container) has the incorrect size and thread for the harbor freight press so that slide bolt cant be used. Can you give us the correct puller kit with the correct slide bolt please?

@hardlymovingpro 3 года назад

What I did was take the forcing screw (puller bolt) with me to Harbor Freight to see if the thread pattern of the bolt matched the thread pattern with the hydraulic adapter. I have 2 wheel bearing replacement kits and the thread pattern on the forcing screws are the same. You must have bought a puller kit with a non standard (should be 3/4") forcing screw size.

@thomaslevine6120 3 года назад

@@hardlymovingpro Can you give me the the kits number w the correct slide bot size because the in the link you gave us does not fit at all

@505fastlife6 Год назад

If you haven't figured it out get the hydraulic hole puncher and front wheel drive bearing kit both made by Pittsburgh at harbor freight.

@meassavuth4649 2 года назад

Great , where can we buy this tools ?

@hardlymovingpro 2 года назад

Check this video's description

@WizzRacing 3 года назад

I never thought of using an electrical knockout set on bearings,... I got an old Greenlee around somewhere...

@hardlymovingpro 3 года назад

It works great!

@WizzRacing 3 года назад

@@hardlymovingpro I bet it works great on bushings too....

@hardlymovingpro 3 года назад

@@WizzRacing That's a different animal needing unique adapters

@maxodorestant9053 3 года назад

Great video as always, where did you buy the pump from?

@hardlymovingpro 3 года назад

Was on sale at Harbor Freight for under $100. Buying the 15 ton pump would have made the job go a little bit easier I think. Plenty of these types of pumps on Amazon.

@Andre-tc1wj 3 года назад

Are you able to remove the hub with the hydraulic

@hardlymovingpro 3 года назад

Nope. That's a different procedure. Here's the link on how to do it: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-I4P3T-cb7rg.html

@kjenkins8648 3 года назад

I am having great difficulty in pulling the hub off the cv axle. I have a 5ton hydr bearing puller with 3 point attatchment on backside of hub flange. I have full tension on puller and have applied heat tapping all around with hammer. Still no give. 2012 kia soul. Sure could use some advise, thank you anyone?

@hardlymovingpro 3 года назад

Did you first release the tension where the cv axle slides into the inner splines of the hub? If not, release that tension first.

@kjenkins8648 3 года назад

@@hardlymovingpro Yes I had already done every step but I finally found a slide hammer to rent from oreillys and got it to pop. Man I hope the next one goes easier on me!

@kjenkins8648 3 года назад

@@hardlymovingpro It was that tension that I was trying to release! Hehe.

@hardlymovingpro 3 года назад

@@kjenkins8648 Well...you got er done!

@ousmanediop9113 3 года назад

How many more times have you used this technique? What's the success rate? The forcing screw being the same thread pitch was that just a coincidence?

@hardlymovingpro 3 года назад

3X. 100%. Thread pitch was coincidence. Perhaps industry standard tool size.

@ousmanediop9113 3 года назад

@@hardlymovingpro I see you left a link for a different tool than the one you used (from harbor freight). Any reason for that?

@hardlymovingpro 3 года назад

@@ousmanediop9113 For those who want to buy on-line instead of running to the store.

@ericschweitzer1654 11 месяцев назад

Way to think outside the box🌞

@hardlymovingpro 11 месяцев назад

Thanks!

@klm82006 3 года назад

Wonder how it would be on a stuck bearing race

@hardlymovingpro 3 года назад

10 tons of pressure is a lot of force coming out of that hydraulic pump.

@tamusbaby Год назад

thank you for posting!

@hardlymovingpro Год назад

My pleasure!

@luiscardonapcardona5243 2 года назад

Thank you for your prompt response.

@hardlymovingpro 2 года назад

You bet!

@julianarodriguez3635 3 года назад

Did you freeze the bearing

@hardlymovingpro 3 года назад

Yes. Makes the install easier.

@jerryolivares5412 3 года назад

I need to purchase the hydraulic pump it'll make it a lot easier for me being mobile to press out bearings especially on front wheel drive vehicles that do not have a hub assembly

@hardlymovingpro 3 года назад

Correct ... and more importantly, not wear out your impact driver / gun.

@jerryolivares5412 3 года назад

Very true thanks for the video

@jerryolivares5412 3 года назад

Will it work if you don't put the bearing in the freezer over night or will it make it a lil bit harder