No video :(

Replacing Studs the 'Easy Way' -EricTheCarGuy

Подписаться 1,8 млн

Просмотров 2 млн

50% 1

I've been asked to make this video for some time and I was just waiting for a vehicle to come in that needed new studs. Well, not only did I get one in that needed a new stud, but it needed 2 studs. This doubles our fun for this video. The principal was the same for both studs. Some of you might not agree with this method and that's OK. But I can say that I've done it this way for many years and have not had one come back yet for an issue. However, if you feel you don't want to employ this method, you can remove the axle nut, slide hammer the hub out of the bearing, replace the stud on the bench, press the hub back into the bearing, and hope your bearing doesn't go bad as a result of separating it. Either way works. Here's some links to some tools you might find useful that were mentioned in the video.
Cutting Wheel: www.jbtoolsales...
Air Hammer: www.jbtoolsales...
Thread File: www.jbtoolsales...
Discussion about this video: www.ericthecarg...
The best place for answers to your automotive questions: www.ericthecarg...
Facebook: www.facebook.c...
Twitter: / ericthecarguy
Google+: plus.google.co...
Information on Premium Membership: www.ericthecar...
Stay Dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 1,5 тыс.

@chingonr 10 лет назад

Done this plenty of times, never had a problem...those of you that are complaining he mentioned many times this is ONE way of doing it without having to remove the wheel hub and replacing the wheel bearing, not everybody has the luxury and replacing every at once for a simple stud, this method is not dangerous.

@MrFredboy 9 лет назад

Recr Actually, that isn't true. This probably won't be, but CAN be dangerous. The shoulder on those studs is all that keeps them from pulling through the hub. On 2 studs, it isn't a huge no no, but if you're doing all 5, find another way, because that's when it becomes dangerous.

@mja9001 6 лет назад

Never had a problem YET.. removing 25% of the retention part of the nut that holds the wheel on is dangerous..

@CharlesCarabott 5 лет назад

@@mja9001 I would think that the force is sideways not outwards so I wouldn't think it's that dangerious

@davidlawhon7506 8 лет назад

I just replaced studs on a 02 ford explorer, the studs I bought came with the heads shaved on one side. Just as you did. The ones I removed from the factory was the same way, So, I guess your right up there with Ford. Thanks for the video

@philr9407 8 лет назад

☺

@amadotacu3707 7 лет назад

David Lawhon lol.....Ford certified ehhh

@r0wdyn3ss 6 лет назад

Maybe Ill get lucky then.

@RedSnakeGT500 4 года назад

"I guess your right up there with Ford" That is a low bar, my friend.

@cjwherley 4 года назад

RedSnakeGT500 b

@davesippel914 Год назад

I’m grateful for this video today. I changed out a broken lug on my son’s 2008 Honda Fit. I used this method and it worked perfectly. Another guy online removed the entire knuckle and needed a hydraulic press to finish the job. I was done in about 15 minutes. Thanks!

@kenlemmond673 Год назад

Just used your tip to replace the two front wheel studs on a 2006 CRV. The hardest part for me was trying to hammer the new stud thru the hub. Gotta check out one of those air hammers from Harbor Freight! Thanks again for the help. You're one of my most trusted resources on RU-vid! Keep up the good work!

@estrelladelnorte1308 10 лет назад

well... i think thats is better and stronger than driving with NO stud at all , think is great that eric is honest and he is there trying to save money for his customers , other mechanics would have recomend changing the hub, brake pads , brake caliper,bearing,axle, transmission and maybe the engine for a broken stud!!! ( if you know what i mean with this) What eric just did made the car safer that what it was before.Gracias eric

@henrietn 10 лет назад

Like eric said, this is the easy way. A lot of people freaking out here. Some people actually look at the cost of repairs, and this way is much less time consuming and cost effective, if the customer so demands it. If he wants the replacement done the normal way, it will be more expensive. Besides, Eric is just putting up a video that youtubers asked for...

@provostkhot 10 лет назад

Freaking out? Man, someone who talks about work ethics shows a video in which he deliberately breaks one thing to fix another? Really? It's not about weather it works or not, it's about sloppy bodged work. We're waiting for a reapir video made entirely on "zipties", I mean who cares about actually doint it the right way.

@ericthecarguy 10 лет назад

provostkhot This is not 'sloppy' or 'botched', the method works and in the right application I have no problem doing it and have never had a problem with this in the many years that I've done it. I think you should focus more on the idiot that cross threaded the lug in the first place rather than demonizing me for fixing it.

@henrietn 10 лет назад

EricTheCarGuy hit the nail on the head right there!

@rubenvarela4077 6 лет назад

Hendrik Derudder yupppppp

@kaineshorts1783 Год назад

@@ericthecarguyhow’s it going eric i have to replace some studs on my car do i need to replace all of them?

@donnybruno3594 18 дней назад

Holy moly! Thanx Eric@ You saved me so much time and money. I heated the hole and froze the bolt. IT WORKED!!THANK THE CAR GOD ERIC!

@barrymckinley2292 7 лет назад

Thanks to your tips here, I was able to do this myself and save myself about $300(The tire shops I called all said about $150 per stud!!! That's insane!!! It literally takes longer to take the brakes apart than it does to remove and install a new stud. Thanks again!!

@Inline3speedy 2 года назад

it's so fucking funny because these mechanics are usually the one who over torque studs and we end up going back to them again for fucking 300$? No thanks, I'll rather do it myself and learn something new.

@silveravnt 2 года назад

The dealer quoted me $615.05 because they said the bearing had to be replaced on a 2000 honda odyssey and it's pressed in so the whole knuckle has to come off.

@eastoahu 10 лет назад

Wow @ all the people bashing Eric for this... I really think its these kinds of videos that you learn things from. Factory service manuals don't show you these kinds of things. Thanks Eric!!!

@joshuacarrasco6012 4 года назад

I agree

@mrbreezeet1 3 года назад

@@joshuacarrasco6012 yeah, it is just fine grinding the flat into the back of the stud. I've done it too. I have even seen factory studs with the flat already machined away.

@stevehillier7018 6 лет назад

The man has been completely open and honest so I don’t see any problem. Keep up the good work Eric

@sixtyfiveford 10 лет назад

I have done this and it is a good reasonable method. Even with the missing portion on the back of the stud there is no way you would be able to draw it through the hub before the threads gave out.

@EpicHeroSandwich 10 лет назад

or before the hub gave out for that matter.

@davelowell3008 8 лет назад

For that type of vehicle, if it's yours. That's the best way to go. I'm sure owners of similar vehicles appreciate this vid.

@toconnx 10 лет назад

When I insert my new wheel stud, I like to throw the stud in the freezer and hit the hub with a heat gun for a few minutes. Those small bits of thermal expansion / contraction make all the difference

@dg-xr3gc 5 лет назад

"We don't want to mess up the threads that's why we're here" continues to hammer the shit out of the stud as it's going in at an angle.

@MicroSoftner 3 года назад

lol

@UltimateSteevil 3 года назад

as a stud myself? i can confirm that chicks love it when you hammer at an angle. :P

@subele_music 3 года назад

its ok they only got booger’d up a little

@DesignatedName 3 года назад

I was thinking the exact same thing 😂😂😂😂😂

@jthresher78 6 лет назад

Can't believe so many people get upset with this method. Nice idea, Eric. He clearly states not everyone may like it, but it is a viable alternative and some of us do work on old cars where what it looks like isn't all that important. Does anyone think some car manufacturers purposely design them this way in order to ramp up the cost and complexity of repairing them? I do. This is what's wrong with the engineering designs on newer cars and manufacturers don't care about the cost to customers, only the bottom line profit$.

$@fractal4284$

@fractal4284 5 лет назад

All the people complaining this is obviously a work around it's clearly obvious that the client/customer probably couldn't afford the extra labor for the bigger job if this method solves it it doesn't hurt anything

@Bones12x2 10 лет назад

I'm lucky I guess, I just replaced a stud on my car and I had enough to get the full length stud back in with no problem. But my grumpy old neighbor did call the cops on me cause of the noose from hammering it in. It was only one stud and the hammering lasted for no more than 5 minutes. Stupid old man.

@ramanpreciado2241 4 года назад

Wow I'm on day two of hammering my rusted in stud. My neighbor did came by though today.....he offered to help me with any tools he had. Great man 😅 sorry to hear yours is messed up.

@roberteberhart1139 3 года назад

Yup! And I'll call um again on ya too. Young whippersnapper

@owenfranklin814 3 года назад

Lol the guy next door always helps with tools or to borrow his jack, sorry bro

@rswindello 3 года назад

I’ve been hammering the new one in for 30 minutes. Feeling bad for my neighbors

@DefendTheStar 3 года назад

You'd think an older gentleman would appreciate someone working on their own car.

@richardsquires6534 8 лет назад

Replacement lug studs usually come with a "D" shaped base for easy installation. And Eric, if you air chizzel that flap that you cut, you can probably drive that stud home without thread damage. Isuzu used to pay 6 hours io replace the studs on all 4 corners. Those were happy days! ; )

@WorkableWax Год назад

Box truck or light suv?

@MrSnowmobilefreak 9 лет назад

Eric, thank you for leaving your videos relatively unedited, its those things that make me chuckle that make your videos just that much better!

@andyshandyshop9207 4 года назад

It's a repair that I have done before, using the same method that he used. He done good! You don;t want to rebuild the entire hub assembly for a wheel stud!

@ThisDoesNotCompute 10 лет назад

Yes, this method works. But honestly, if I was paying a shop to replace a stud on my car and they did this without asking first, I'd find it very unprofessional.

@TheRick2130 10 лет назад

with that kind of hub bearing there's 90% chance you wont be able to remove without damaging the bearing.. as soon as you pull the flange and the bearing race came off that's another $$$ specially on honda,toyota that a freaking big $$$

@ThisDoesNotCompute 10 лет назад

Oh I agree, just saying that if anyone is getting paid to do this kind of work, they should be upfront with the customer about exactly what they plan to do. It's like going to the dentist to get a cavity filled and they decide to just pull the whole tooth because it's faster/easier/cheaper. In this case, eliminating the risk of damaging the bearing comes at the cost of a cut-up splash shield and a weakened wheel stud (since part of the head gets ground off).

@user-nl9ne5gk6k 6 лет назад

the bearings aren't all that expensive when you get parts through a real parts supplier, and not from a schlep boiz or autobone! lol

@sunsweetsuitable593 6 лет назад

this is why you never go in the work bay area

@mopar0IIII0jeep 6 лет назад

At $100+ an hour for shop time the alternative will cost the customer a couple hundred extra bucks for no real benefit. The more of a pain in the ass a job is the more it costs the customer.

@bmxpeter8 9 лет назад

Makes me laugh those who complaint about this method clearly never worked on old used car someone wanted fixed on a budget (which is the type of job 90% of independent garages live off). Its not the type of procedure you do on a brand new Audi, Eric knows it... its something you do on a 1998 Sunfire that someone use as a winter beater. and I'm ready to bet that those stud wont ever go anywhere.

@ariso 7 лет назад

The customer paid for 2 new studs, one of which was broken, and the other one had damage threads. They were then replaced with 2 studs with damaged threads. Plus, he spent time polishing threads and grinding down the studs. He should have just removed the hub.

@eurobeatmachinist732 7 лет назад

Aris Oglesby Grinding took about 10s, If you can remove a hub and replace the bearing in that time just go ahead and do it.

@headphonesnotincluded1700 7 лет назад

But still. At least do it the right fucking way. It takes less time and less effort to do it the right way, than it does this way.

@amadotacu3707 7 лет назад

Pierre Gauthier preach

@georgeghneim 7 лет назад

@unclematt3 4 года назад

This is a small, easy fix that helps avoid a lot of time and expense. It's doable for a guy in his driveway. Thank you for showing this.

@steveaverbach164 9 лет назад

Eric knows his stuff his advice has been extremely valuable in repairing our Acura CL Captive Rotor and wheel bearings!

@domari9459 10 лет назад

Brilliant Eric. I'm an IT guy who does my own car stuff in the backyard and garage, and everywhere I can access without aggravating others. ;) Your methods are spot on. They are great for guys(and girls) who work on their own cars, and for pro's as well. A whole world of making my own tools has opened up to me by watching your videos. Keep up the good work mate(I'm from down under) :D

@andrewmayhue 10 лет назад

Eric great video!! I have been a mechanic for thirteen years I have done this numerous times NEVER had a problem. I wonder if those people who are complaining about your repair know the tensil strength or rockwell rating of a wheel stud look it up it may suprise you! !!

@th3b0yg 4 года назад

Not picking a fight, but what does Rockwell hardness have to do with it in this case? You're thinking something like if it's hard it'll be less likely to deform under load? But I agree with you that this repair is perfectly acceptable.

@itzchaparr0661 7 лет назад

people actually getting mad by this method, i did this to my nissan like 4 yrs ago, and the wheel hasn't had any trouble :), Good job Eric save the customer some money

@Quake3DeathGod 5 лет назад

I totally appreciate this video! It is a massive money saver on a Honda fit! What would have taken me $400 at a shop or two days in 17 degree weather, took me about 30 minutes. Thanks again for the video, keep up the good work.

@josephmckinney4816 2 года назад

About to do this with my 2012 Honda Fit. I'm so glad to see your comment on this.

@Hachiro 8 месяцев назад

@@josephmckinney4816 2008 for me! Doubt I cross threaded the last one, more likely that I over tightened it. Too bad it didn't happen to one of the rear studs, cause the whole hub is super easy to replace.

@DJzSith 10 лет назад

This works 100% and is much quicker, easier and minimizes risk of damaging something. That being said, I would inform the customer about the costs of taking of the knuckle and doing it properly and hope he would accept, before pulling off this sort of improvisation on his car.

@edwinreeves6506 2 года назад

My only concern is ,would it still pass a state safety inspection. My state ( Missouri) still requires inspections.

@davidbrennan5 7 лет назад

This is what I call a rough and ready repair. It is not pretty but it works and the car is fixed quickly.

@Hole_Motorsports 3 года назад

This is what I call a lazy hack job

@johnpaulgarcia6906 4 года назад

I don't like how it's done but it works plus it saves money and it really doesn't harm the vehicle's steering. Great job sir

@wingman1861 10 лет назад

One of the many reason i still drive a 1gen dodge neon.the gap is already there to remove the wheel stud and you dont even have to remove the brake caliper. Its a good way to do it eric..dont listen to the haters.

@eastoahu 10 лет назад

That is a horrible reason to justify having a dodge neon.

@dav3fk 10 лет назад

You pick your car based on how well it caters to wheel stud replacement? I wouldn't drive a hunk of shit, just to make it easy to replace a part that should seldom need replacing, if ever.

@crawfordoverton7786 10 лет назад

I found using a few flat washers and your lug nut tighten the nut against the flat washer pulling in stud flush. I have used this with a great deal of success never a failure.

@winstonbuzon 10 лет назад

A few? How about one big but strong one? This method sounds good, but would that mean you'd need a longer stud?

@dohnjoe9324 6 лет назад

Good idea ill try that i have big washers that will work perfect! I aint buying no power hammer tool ;)

@FragItAll 5 лет назад

I've done it this way (with washers), works for me.

@gitmoray1 10 лет назад

I am sorry that so many people watch a free video that thinks outside the box, and all they can do is bitch and complain. I really like the fact that you do very detailed videos, with decent takes and closeups, and that you explain all the pros and cons as you did on this one. My only suggestion would be to throw the studs in the freezer after grinding them down. If you freeze them before insertion, they will go in a lot easier. You have saved my butt on several occasions already. Please keep doing these videos!

@mrbreezeet1 3 года назад

Yeah freezing the stud that's a good idea. As I mentioned before I think Eric said some may not agree with grinding that flat onto the back of the stud I've even seen studs in a car that were like that I don't know if it was factory or or they made it aftermarket like that for that reason but that studs not going anywhere with a little bit of that flat ground off what the heck?

@eliseviv 4 года назад

Thanks to Eric of the past. Your old vids are still the best. Ill be getting a thread file out later today. ;)

@tviele1 10 лет назад

good video...shortcuts i have used many times...quite a few studs come from the factory with a portion already flat spotted for clearance issues... when drawing a stud in with a lug nut i would recommend lubricating the threads to prevent damaging them with the high load you put on them trying to force them in...

@treydogg77 4 года назад

Take a angle grinder and bevel that hub guard more. Less likely to damage the threads on the new studs. Nice shortcut I like it a lot!

@danielmoore17 4 года назад

That's great! I wouldn't do this on my nice car, but I just snapped a stud on my winter beater, time to bust out the grinder. Thanks bro

@izyb478 3 года назад

I did somewhat the same on me 06 civic si front end. Bent the shield back in the smaller area and cut the cross threaded studs that was so very nicely messed up by tires plus and grinded the side as you did . Not flat though. Needed an angle to slip it in with the use of a 2lb 🔨.fyi tires plus has lost my any business in the future. It will be the 2nd time they do this to the same car. Thanks Eric. I have worked on a 93 accord and my 8th gen civic because you are one of the people out there which have been able to help me gain the confidence to get dirty and make it happen for myself.

@mememan2344 2 года назад

89 honda civic here- and yeah. No way I'm taking the whole assembly off. Thank-you for saving me time and money.

@jayohhhohhh2875 4 года назад

This doesn't look easy at all

@ohmythatsweird 7 лет назад

Half the people that thumbs down the video are the same people that wont pay the extra money to do it the proper way. If all mechanics went only buy factory spec,they would all be rich. This is clearly a work around for certain occasions .

@Shorefire100 5 лет назад

for those afraid to try this have no fear, last night I spent 3 hours trying to thread that lug stud past the heat shield of my 2014 CRV. afraid to cut that heat shield because it is a newer vehicle I decided to bite the bullet and take it to the dealership to do it the right way. Long story short, guess how Honda dealerships do it? THEY CUT THE HEAT SHIELD AND FLATTEN THE HEAD ON THE STUD!!!! WELL DONE ERIC I'LL NEVER DOUBT YOU AGAIN!!!!

@momadnomad9018 5 лет назад

In CT, the state police have oversight on repair practices such as you describe. Give your authorities a call and you might find that dealership more than willing to redo the mess they left you with. PS Two wrongs will never make a right. Slash and dash repairs have no place in amateur or professional repair practices. If you can't do a job right, don't do it at all. If this comment is thought to be hating, so be it.

@tylhunt 3 года назад

@@momadnomad9018 It'll just be 5x the price for essentially the same job.

@johncornharvester 10 лет назад

i've done this twice, on a honda accord and subaru forester, both worked great. would not hesitate to do it again, thanks eric.

@TrojanHorse1959 10 лет назад

Eric, When "pulling" a stud back in, try using a larger nut or stack of flat washers for your old nut to pull against instead of directly against the hub. It helps keep the stud from wanting to twist. Also lubricate the threads and the washers or larger nut contact areas to reduce the friction. It works for me when I cannot get an air hammer to the back of the new studs to drive them in.

@johnlagreca6288 2 года назад

The air chisel works too.

@ShelleyYbarra 2 года назад

What do I do when the washer become stuck on the stud?

@armchairtin-kicker503 Год назад

There is a tool for installing studs: Lisle 22800 Wheel Stud Installer.

@benhyzy3662 Год назад

@@ShelleyYbarramust have been too small of a washer. You’ll have to break it off, try heat.

@benhyzy3662 Год назад

I used the closed end of a 1/2 combination wrench (didn’t have enough washers laying around the garage)

@miloman812 4 года назад

Dude really knows his shit. Love how fluently he speaks as well. Goes to show he really does know what he’s talking about. If I made this video, I’d be saying “uhmmmm” a lot

@fragmare 6 лет назад

People talking smack about this procedure must not realize they sell pre-notched studs, like the one Eric made, for exactly this application. Also, a jamb nut or axel nut makes an excellent washer to put between a lugnut and the hub flange for pulling the stud through... never had one spin in the hub.

@homeboy391 5 лет назад

Awesome. Thanks Eric. I needed this video cause I had no idea how to replace the stud on my 06 Sonata without removing the wheel assembly, which is quite a chore. Some have commented that if a professional shop did this they would be upset. Honestly, if a professional shop use this method and it will resulted in less labor hours and parts for me then I wouldn't mind at all. I'll definitely invest in an air hammer. Thanks again!

@MichaelMantion 10 лет назад

I changed 2 lugs on my sequoia, I didn't have to cut anything to get access. That said when I put the lug in I froze it in my chest freezer for a week. I am sure a day would do the same thing. I cleaned up the hub a bit and the lug slid in with some washers and a lug nut. took almost no effort. I will say that I tried it another time w/o freezing it, I got it but it was much, much harder. I am often amazed how much steal shrinks at -20f, which is what my chest freezer is at. I guess if you really wanted you could use dry ice to get even lower, but that is $$$. I have used dry ice to get transmission bearings into place but I wouldn't waste the money on lugs.

@LH81633 3 года назад

Issue is the length not fit! No room to remove insert unlike other manufacturers that put at least one hole so that you can pound it out and easily put in the new one!!!

@CptMishMashVonRandom 10 лет назад

You were going good until you beat it in there. It is possible while not damaging the stud at all. I do it by completely cutting out the piece as you did, then with a grinding stone I grind the surface of the knuckle back a tiny bit where the loose stud bumps it. You don't need much off, you just soften the sharp edge and the stud will fit straight in there. :)

@th3b0yg 4 года назад

Nice tip! Thanks!

@tedbonbrake1967 6 лет назад

Ouch... I love your channel and most repairs shown are valid. I have actually done this repair on my personal cars a few times with no adverse effect. When you used the side of the grinder to make the flat on the lug though I had to cringe. My left tear duct just under my eye still carries a chip of a grinding wheel that exploded doing that exact thing. I was wearing safety glasses too, but when the bolt jumped just a little, I turned my head and when the explosion occurred, the fragment ricocheted off the bottom edge of the glasses and imbedded itself just under my eye. It looked like I had lost a bar room brawl for weeks. I still use the same method to this day, but wear a full face shield. A caution at this time in the video is warranted I think...

@frankm2385 4 года назад

I got ready to bang my wheel stud out with a hammer until I saw this video. Put it back and grabbed the air hammer. 10 seconds later I was putting in the new stud. Thank you 🙏

@tinydx95t2 10 лет назад

I think that what you've done here is acceptable. I think that there is plenty of "meat" stud left on the stud head as you stated in the video.I've found that if you don't clean out the hole the stud will usually pull in without spinning using the lugnut method.

@NigOleBigger 7 лет назад

"You don't want to booger up the threads" proceeds to bang it through the hub

@bossmaine601 4 года назад

😂😂😂😂🤣🤣🤣

@elmecanico4943 4 года назад

I would put grease on the threads and hole where stud goes in.. To minimize damage..

@specialed618 4 года назад

At least he owned up to it lol

@juliansaiz5714 4 года назад

Lmfao yo

@twx895 10 лет назад

A suggestion that I have, coming from a manufacturing background, with having cut threads a lot, and fixing messed up ones, when ever I had to fix old threads, I would just take a thread die to them and recut the same size thread, that always worked for me, so I do the same with my automotive work and never have any issues after I do that

@MrPew17 10 лет назад

You can call him a cheap lazy hack or whatever you want, but it works, and that's what counts. As always, great video Eric.

@jsnjud 3 года назад

Thanks for the video. After watching it, I was expecting the worst on my 2010 Honda civic. Luckily, they designed it with a convenient hole in the shield to pop the old one out and put the new one in without having to grind or cut anything.

@thesilentdiva Год назад

I love Honda, so practical

@tyree9055 3 года назад

Thankfully I've not had to deal with engineering this bad regarding wheel studs. But once the splines are aligned and it's close to being fully seated, I just torque it down when I put the wheel on. Stay Dirty & Studly! 😄

@MorrowSind 5 лет назад

My mom had her car inspected and the mechanic forgot to tighten the lug nuts on the one tire after rotation. The car was making a strange noise 2 days later after she drove a 20 mile trip and back. I jacked the car up. The tire was wobbly, so I took it off, and two lug nuts fell out; both broken off. This method looks great to me. Thanks for the video.

@MorrowSind 5 лет назад

The studs fell off with the lug nuts after I took the hub cap off. I forgot to mention that. It's late here.

@tarnowek1 8 лет назад

Excellent video...thinking "outside the box" ,as usual EricTheCarGuy has come good!

@henrybikeman 4 года назад

Pro tip for those worried about damaging the bearing while hammering out the broken stud: Leave wheel on ground and all good nuts tight. Drive broken stud back into hub using stiff punch. All the shock is taken within the wheel and tyre. Remove wheel and continue. I just did it with 2 good hammer blows, on a Toyota.

@random12345457 6 лет назад

oh my goodness that air hammer is amazing

@Jademyheart 3 года назад

Yep,💯👍 that's MaC for ya😉

@jasonardenyi1036 3 года назад

Yes, verry nice

@dougpenn814 2 года назад

Đirt diger hamberger job not even if it was free sorry

@naturalresourcepro8383 3 года назад

I'm here because I'm currently doing this job myself. Couldn't believe a broke stud turned into such a huge job. Personally, I wouldn't do it his way, but I get why people do. On my 07' Honda CRV, there is zero room for cutting - the back of the stud is not too far from the bearing housing. It's of course not a removable assembly either. I was able to leave the steering knuckle partially installed, and with the CV joint out, I used a puller/installer on the bearing and hub assembly.

@everettclunie3525 8 лет назад

I put a stud on a car for the first time today. I used a lug nut to draw the stud back in but I put several washers between the lug and hub down the stud. that did the trick to keep the stud from spinning too much while I turned it with a big boy ratchet. It was an 09 Hyundai Sonata and I lucked out with being able to get the angle to slide the stud in from the back with out grinding or cutting anything. But thanks to this video I managed it, so thanks for sharing the easy way!

@jamisgood21 10 лет назад

THanks for yet another great video Eric! Wish i woulda watched this a few years ago when we did a few studs on my buddy's car. This is the method i will certainly use next time i need to do this. Surprised i didn't think of it earlier. As always, LOVE your vids man. Don't ever stop.

@MandrewP 10 лет назад

Like Eric said, it's one way to do it. It's one option. And I believe that option has it's place. Anyone with any mechanical sense knows that this is not a structural weakness that endangers anybody or anything. We live in a real world with real considerations that need to be made. If someone has an old car that they need in order to stay employed and can't afford to replace the wheel bearing too, then this method is a blessing and saves the day. So why not? Those that say it's bad engineering need to get off their "high standards horse" and develop some consideration for their fellow man. We don't live in a perfect world. This option is perfectly viable and can be very beneficial to someone in need. In no way can anyone rightly say that this method is too dangerous or risky. It just ain't so! Now you may not want to do this on a new car, or to just save a rich guy some money, but it certainly has a place among the viable options for this kind of repair. It just plain cold hearted to ignore somebody's car repair dilemma for some irrelevant "high standards" crap. THAT'S what's stupid!

@Crabtownresller 2 года назад

Facts

@matthewstorm5188 2 года назад

@ MandrewP On the other hand, there are better ways of dealing with this sort of thing. For instance, you can get an entire hub/knuckle assembly from a self service salvage yard quite cheaply and just swap the whole thing out. Yes, you have to take the time to go to the junkyard. But this is pretty simple for a DIYer. And the knuckle swap can be done fairly quickly.

@stephentaylor5311 7 лет назад

dude. when you started bashing that thing home, it was beautiful lol real world working on rusty cars.

@ronijr4918 3 года назад

I can confirm that this is actually the best and time efficient to replace a stud.

@12101DyM 8 лет назад

To draw the stud in without an air hammer just use the lug nut and and another nut that slides over the stud, but doesn't thread on.

@CCWSig 8 лет назад

That's a incorrect way of doing it. That way will cause the stud to stretch and fatigue. Using a air hammer as shown, or a press is the only correct way.

@antoniomunoz280 8 лет назад

An air impact is not incorrect, it's just another method of doing it. And an air hammer is another, neither methods are incorrect.

@CCWSig 8 лет назад

You are incorrect. Using a impact can over torque the studs causing them to stretch, crack and ultimately fail. That's why there are torque wrenches, and published torque ratings for bolts. 150,000psi tensile strength sounds like a lot, but it really isn't, and is easily achievable with a quality impact gun.

@Mebob2001 10 лет назад

for people thinking this would not work, you need to understand the mechanics beind it, the part that he did not grind off is trying to be pulled through the hole in the hub, there is so freaking way that is going to happen, the stud will snap before that happens, lug nuts will still have the same clamping force on them as before, nothing is weakened in this process, dont get me wrong i rather do it correctly but if it was my own car or truck, you better beleave i would do this, yes i am a tech like Eric but i work for Gm on diesel's

@Mebob2001 10 лет назад

there ya go, people shouldnt saying anything hahah

@q...... 10 лет назад

From my understanding the pull through force that it can take before the end snaps off is limited, and depending on which side is shaved off it can weaken it laterally to that side, but generally speaking the difference is not enough to make a huge difference.

@SpinolaEnrique 10 лет назад

I'm sure the customer would be happier with the bill coming from this method, instead of the cost of paying for remove hub, bearing, and whoever knows what else. I really like your videos mate ;-)

@willrobinson9575 10 лет назад

Most mechanics would charge what it cost to do it the right way and laugh all the way to the bank.

@latitudemarine4975 8 лет назад

Definitely going to use this method on my 2012 sentra. It couldn't be any more unsafe than driving around on 3 studs and I don't have the money to replace bearings and cv axles. Thanks for the vid.

@dabruiser7938 6 лет назад

Did the same thing on my 2008 Accord in the front passengers side. I had to grind some more metal between the hub assembly and the dust shield for clearance. 11k Miles later and no issues, and I have taken off that tire a few times since with no issues. This is a cost saver, and don’t worry to much about the metal not being strong enough after tapering the head of the bolt because it’s still better to have that than not to have a lug nut on it anyways. Godbless

@striker851 10 лет назад

Eric, I love your videos and frequent out-of-the-box thinking. This video is a pretty big hack job, though. Cutting, messing up threads on a new stud, just not sure about it. But, thank you for your efforts and numerous videos.

@pjkentucky 3 года назад

When I have the problem of not able to feed a stud in the hub due to no clearance with the backing plate,I use a hole saw to make a 3/4" hole in the backing plate so the old stud can be removed and the new stud installed. I then take a solid rubber grommet to plug the hole when I'm done.The time would about the same and you have a nice finish result.

@762N8O 6 лет назад

Entertaining to say the least. Reminds me of when i was in high school and broke as hell You have steel nuts to post this

@onogrirwin 4 года назад

Sometimes, the customer has the money for the full procedure as specified in the manual. Great! Sometimes they have $82 and need their car back on the road to get to work. You going to help them or tell them to fuck off? That's why we do things like this. Different procedures for different situations.

@vcdrny 10 лет назад

I've done this many times on different vehicles and I guess I been lucky that I never ha to cut anything off. There is always a space to get the old ones out and the new ones in. Note to self stay away from older models Acuras RL.

@davidlawhon7506 8 лет назад

to all the people who are complaining about the way this guy put the stud in, yes you can pay a mechanic to do it the long way, but is going to cost a lot more. Some people just dont have the money including me. why give away money if you dont have to. But if you have money to burn, why not buy a whole new car. There is nothing wrong with the way this guy put in the stud.

@MrRainbowrooster 6 лет назад

Very good video. My car is 11 years old and I'm comfortable not spending the extra time and money involved doing it the other way. Thank You

@timothycwillis 7 лет назад

this works fine. good job

@dhestondh 8 лет назад

great video used it today on a prelude Eric ur the man bro love the videos

@boofdfast 8 лет назад

What year prelude? Mine is an 89 Si 4ws, and it has two broken studs... What a pain the ass. Replaced two studs on my 81 280zx, took less than a half hour. Fwd SUCKS.

@irishk5blazer 10 лет назад

usdot has a rule on stud design a> you have taking the harding out of the stud by heating on the grinder b> you have cut a 1/3 of the strength away. C> that dust guard is there for a reason. but guess your right make it cheap screw doing it right and screw the threads up in the process

@mexskal 10 лет назад

hahahahaha really hahahahah because he took one third to the stud u came to the conclusion that the took one third of the strength sure and the grinder didn't get it that hard to change anything because it needs to get way hotter to affect it and the ventilation shield was not affected because he did not cut the actual shield just one section which does not redirect air to the rotor due to the small size. u could consider it a inert section meaning honda could easily not include that section in the shield period so i don't know where u get ur info

@fisqual 10 лет назад

Almost all of your videos confirm a shortcut I have taken in the past, and for that I love you. lol

@danosleeper9294 6 лет назад

Good shit! This is exactly how i do mine.good to know the world has some smart people left

@GloveBunniesVideos 10 лет назад

A somewhat elegant solution to an obvious design flaw. ;-)

@tyree9055 3 года назад

Yes, the automotive engineers f'ed up on that one. What were they thinking? I wouldn't buy a car where the engineering was this ignorant! 😅

@VeryTucker 10 лет назад

I've seen this method before. I do not like the idea of grinding off any part of a stressed stud's head. While there is not nearly as much lateral load on the wheel hub when compared to other forces, there is still some. While this is not really a big deal and I am 99.9% sure nothing will ever happen to it. I just don't like the idea and I couldn't sleep on it. I appreciated the video though! You have taught me lots so thank you for that!

@pcofranc 6 лет назад

I loved the method of driving the stud with the impact hammer! Never though of doing that - although the "hammer head?" driving bit never seems to be included with harbor freight tools only the chisel bits. Have rarely replaced studs and have never had to trim the dust cover (just bent it) but THANK YOU for showing a car where that is necessary AND where the head of the stud needed to be clipped to get it installed. There is 5 studs on the wheel no way shaving the head will ever matter - but if it matters then take the wheel off and risk replacing the bearings - it's the mechanics choice :-). Finally, I have always used the lug nut to install the studs: 1. Grease or anti-seize the vertical grooves 2. hammer the back to get things started 3. power on with the air gun as you hammer the back of the stud to "help it" into the hole. However, I never liked doing this method because of the strain it puts on the lug nut & the new stud. Now I have a new and better way to mount the stud and I still thing greasing the vertical grooves helps with the install even with your method - THANKS!!

@nickb4302 10 лет назад

Very heated debates on this video about torquing lug nuts. How hard is it really to pick up a torque wrench? Does it really save you that much time not using one?

@JustinCrediblename 9 лет назад

Hmm let's see I've never had a problem not torquing my lug nuts. Same with so many other guys. what do you say about that? blind luck?

@christopherkatz9484 3 года назад

It is pretty hard to pick one up when you don't have one 😅

@shodanxx 8 лет назад

Why not dig a groove in the knuckle ? Grinding off 1/4" into the knuckle casting seems to me safer than removing 1/3" of the stud thrust surface.

@Bryce.H604 8 лет назад

+shodanxx so instead of effecting an interference stud with a hubcentric wheel (takes load away from the studs). You what to score also heating a cast piece of the suspension, which will than shatter the first pot hole u hit hard. its not 100% proper yet customer didnt have to pay an extra $250 they probably didnt have

@shodanxx 8 лет назад

The casting is about 1 inch thick at this location. You don't have to heat it, just grind a bit off. As long as you blend it smooth it will do nothing bad to the part. Castings work mostly in compression and most of the weight goes through the knuckle's central axis. This is nothing compared to what corrosion does to these parts yet they rarely break. Those studs hold just as much weight as the entire knuckle and they do it on that tiny face which just had 1/3 of its trust face grinded off. Way, way better to grind that off the knuckle rather than the studs.

@ferreiraaveiro3908 8 лет назад

+shodanxx i was thinking about that

@BigBrotherIsTooBig 8 лет назад

+shodanxx Think about it this way...that stud with 1/3 of its face ground off does more to hold on your wheel than a stud without a lug nut.

@shodanxx 8 лет назад

BigBrotherIsTooBig It also does less than an intact stud.

@dylandrumhero6 7 лет назад

Thanks for the tip man! I gotta get new studs and start this project ASAP, just snapped a couple lugs putting my summer wheels back on.

@josuebarahona7873 2 года назад

Some of these studs come with the cut Eric did!! Great video

@danabasinski 10 лет назад

Can vouch for this method working well, did the exact same thing on my 95 Honda Civic. Worked well and was quick and easy.

@gvvq-pi5ml 10 лет назад

Hi Eric, i worked in the trade for 45 years so i know what your up against and how you feel, at the end of the day would the owner want to pay you $300 to do it the other way, prob not, you got the job done with minimal damage, i cant see the stud ever pulling out...i too found it hard pulling through with a nut, air gun seems to do it better, lot of crap sent to you on these comments, maybe they would like to have a go at it...Fred uk.

@gruberhoffman 2 года назад

I know that this video is almost nine years old but I was looking for a way to replace a damaged wheel stud on my 2003 CRV. It looked like there could be many additional problems stripping everything off. I will certainly check this out. Thank you for showing a possible work around.

@robertbilicke8027 3 года назад

Not appropriate for professional work. Absolutely appropriate for DIY! Thanks for the video!

@man_on_wheelz 8 лет назад

A mechanic replaced a stud on my moms rear wheel during a more complicated job and apparently screwed up real bad. Some time later she tells me her car makes a popping sound sometimes when she's backing up, I couldn't figure it out right away. So some weeks later when I got the chance, I removed the brake drum to change the shoes and hardware and immediately I see there's a broken spring just floating around in the drum and the brake adjuster was all bent to shit. So I'm like what the fuck could have caused this nightmare?!?! I remove the backing springs and the pins are bent all out of whack, and as I'm removing the shoes, half a rusted stud comes tumbling out of the assembly. There you have it! Whoever she took it to to get that work that involved replacing a stud done, they just hammered it back into the drum assembly, was probably too lazy to take it apart and retrieve the old piece, put a new stud in, put the WRONG TYPE OF LUG NUT ON THE CAR and sent it on it's way. I wish she could remember who she took it to cause I'd drill them a new asshole for causing us all this trouble. Do you know how hard it is to get a new brake adjuster for a 2003 Mitsubishi Outlander?!?! Out of sheer luck I found 1, count 'em, ONE Outlander at the junk yard with the back drums laying dug into the ground. I had to pull a jack from another car to lift it a little to get the part out. In all the years she's owned that car I have never come across her car at the yard, it's actually a really well built car and reportedly seems to run forever.

@joeespinoza3981 8 лет назад

people don't understand this method is wrong should not be taught thank God this guys mom didn't get hurt or worst

@SnowNinja 10 лет назад

Don't use an impact gun to tighten lugs on a car, you can lightly drive them on but do not impact them tight, use a torque wrench with the manufacturer specification to avoid doing this =)

@sexualldragon 4 года назад

Eric to the rescue as always. Feel like a day one fans. Going back 9 cars with me. But your stuff is always a first video. And when I see yours pop up. I know it’s the truth.

@illusmode 10 лет назад

EricTheCarGuy, Thank you! I have a 2001 acura CL and replaced a stud using this method. Worked! I don't have air tools and it took me a few tries. But i just used a hammer, nail set kit (used to countersink finishing nails), bench grinder, vise grip pliers, rachet, rope to tie caliper, and sockets. The nail set kit worked really well to punch the stud out (I was lucky enough that my stud broke short enough that i could punch it out.). I'd say maybe a punch would work better, but i thought this tool would be useful down the line in household work. Anyways, thanks again.