Resin anchors | Resin fixings 

Wonderful workmanship; delightful to watch!

Thanks fella for the video, another technique I have never used or seen being done. Thanks for sharing this. Neil.

Very nice! You make it look so easy!

ABSOLUTE GENT, THANKS FOR GETTING BACK TO ME , YOUR AN ASSET :)

Once again awesome. Learning all the time :)

Good video. Very informational too.

many thanks for this it saves me a fortune and time using this method

Thanks ,informative and straightforward without any fuss 👍

Thanks for posting the video. It was really useful! Andy

Good Job!

Great video. Will use the same technique for mounting a ledger board.

I`ve never used that type of resin before but have used the type in a glass tube which you place in the hole and break with the stud. Used to cut the stud at an angle of 45 deg and screw it in using a battery drill. All of these chemical anchors are solid with no stress on the surrounding material. Great vids fella.

Great stuff mate, thank you👍👍👍

Looks really good, it really sets up that quickly... It must as you have promoted it. I will see if I can find it here... Thank You...

great vid.

Great video. Thanks for info.

Great video

VERY USEFUL

Thanks for this. Just about to install a chin up bar. Tried wall fixings but they don't take to my interior walls. Someone suggested resin bolt kits which will do the job hopefully!

Could you use this technique to put up a punchbag bracket? Informative video

You are brilliant-

Handy tips.

good as always :)

HandyMan! Can you do a video (when you can) on how to prepare a wall for wallpapering and how to wallpaper tips and tricks plz. Cheers

nice video :)

Hi, I'm wondering about fixing a metal balcony using these. Should I use a rubber gasket behind my washer to take up some expansion - black metal balcony on sunny south facing wall? Thanks mate, I enjoy your videos!

On a standard right hand thread you should twist the stud in anti clockwise as this pulls the resin downward into the hole. Twisting clockwise will screw the resin out of the hole.

nice one as always uth, can i ask where do u buy your fixings from, im finding the local providers quite expensive.

great video...planning to use this.method to fit 20ft ledger board on my house for a deck...what distance do you suggest I leave between fixings?

Good video, I'm rather surprised that you didn't put your timber onto the protruding studs before the resin dried, that way you would be sure to have perfect alignment when it was dry.

It mixes perfect from the get go - it’s designed to

Hi want to put a punchbag bracket on the same sort of house bricks outside . Should I have use same procedures ? Please advice Thank you in advance : )

Can you use screws in resin. I'm trying to fit a countertop shelf for the basin in the bathroom and the last screw just keeps spinning. Space is tight and the only thing I can think of is a chemical fixing? Thanks

What do you suggest for fixing into block work, it's a supporting wall but think it is the thermalight block. Iv got masonary bolts ut not sure which hold the best

what make is your sds drill? cheers

What I don't understand is how you ensure the stud ends up in the centre of the hole if you're drilling the hole ~2mm larger than the stud itself (to allow for the resin). I want to use this technique to mount brackets for a desk so it's vital that the studs are right in the centre of their holes otherwise the brackets won't fit onto them, and/or the tops of the brackets won't be level.

How many holes did the tube do mate?

Nice to see the vids coming thick and fast. Could you have also used expansion bolts in this application?

Would this hold alot of weight? I need to build a pergola on my terrace. I want to screw the studs onto the walls which are made from concrete blocks, these studs will basically hold the whole pergola together. Would it hold the weight? Thanks alot mate.

I have very soft internal walls and any convential fixings just pull out, since it's impossible to keep the hole to size. I have been using resin for years Thanks for the video but I was a little concerned how close to the mortar joint the holes were.

could you tell me what type of resin you use for the brick?

Which is the best place to drill in a brick wall for fixings. Is it right in the middle of the brick or in the pointed area(cement)

what do you suggest to mount a 64lb cabinet to a cinderblock wall? I plan to add about 45lbs of items inside the cabinet. I've been going crazy tying to figure out the best way to do it. Thanks for any help you can add.

Is the resin really that strong that it can stop the studding from turning once you start to tighten the nut? Any idea how much torque can be applied? Could the stud ever turn if enough torque was applied?

Maybe a silly question but has anyone ever used anchor resin as a grab adhesive. Would it work ?

Can there be used to go into plasterboard and then into brick to hold a TV on the wall?

Someone’s got a load of resin on there garage floor and 3 studs sticking out lol

When you say "straight through the brick work"... are you going right through into the cavity or do you stop about 10mm so shy so the resin can't pour through?

Hello and thanks for sharing. One question: what if the studs need to be removed for any reason? Is it possible to "unscrew" them using a particular procedure or the only way is to cut the protruding part and leave the remaining part inside the wall? Thanks!

Best to avoid drilling a hole in the mortar between bricks - makes it much weaker if you don't.

I'm in the States and totally confused. You suggested using a 110V drill (or RDC) when working outside. Seeing as how the U.K. is 240V, where would you find a 110V outlet?

Cool :P

How deep was your cavity that tube didn't look long enough I would have pushed a rod in first to measure depth I think

where do you get mason mate from

Screwfix has different types of easyfix resins; polyester, styrene-free, & vinylester. Any idea how they differ & perform?

Bolton or Darwen????

How do you clear the nozzle tube after you used it? Ive just used a small amount of it,and now the nozzles gone solid,rendering it unusable again. I see you can buy spare nozzles though.

looking at the brick pattern you would think thats a cavity wall, wouldnt you?

Than

Mavie aufgepasst kaufen siegen unterdachung

The yandles, and into de yole hilarious sorry mate...

Great idea - horribly expensive way compared to conventional fixings, and you can't store the resin for long periods, which has always put me off. That stuffs about £20 worth on the consumer market isn't it?

1 - No home DIY has 100v equipment. an RCD would suffice 2 - you didn't hold the drill straight, ie its drilling downwards! Good luck with alignment!

Into de yole ha ha...

All wrong here :)