I must say, I been in almost all the websites, forums, listening to people trying to explain things. so far you explained it so well and shown the result in black and white , I cannot thank you enough. I hope to see further demonstrations and maybe to gain some of you knowledge.
Dear friend the project you saw in my channel is working very well and it can demonstrate the unusual high power at the output! If you are well skilled with Tesla's patents you can understand how it works. The only problem is the high frequency at the output. The electric power can not be rectified and stored in capacitors (that is why you see a light bulb there as a load). Now i am working on another similar project with lower frequencies to demonstrate better the over-unity effect. Stay tuned!!!
Thanks for sharing, that is a beautiful inductive oscillator configuration, indeed I’ve found that finding the standing wave resonance, and then harmonic of that is beneficial to efficiency, as you state the key is to tune it.
man I wish you were my neighbor. I understand your way better than other scematics. I will do it your way and hope to achieve it. thank you so much for your help and keep going forward
I spent 3 years on other things already. I have all the time in the world to make one working device so I gladly spend time to tune it. at this point , even if I can get 10 watt out instead of kw I be more than happy. at least we can prove that there is a way to do it..thank you so much for your time and responses, I'm looking forward to watch your future videos..Be well.
do you have any interest in akula or ruslan replication? I seen the same wave form on several patents including Meyers hho generator. I think the yoke in all of them runs to produce running current with almost no input. user a. valon demonstrated Ferraro resonance with single mosfet with 0 amp input inside square wave. if we can do that ,using the current to drive kacher cuircut and than short it at peak as you shown us, I think we will achieve what we are looking for. I also think vasmus is using exactly what you are doing with internal triangle pulses to drive the cuircut with minimum current input but maximum voltage
I would say that my project is similar to Ruslan Kulabuhov. ( i am not sure about Akula or Vasmus). Instead of the freq. generator (with ferrite core) i am using the Katcher and instead of the Granate - coil i am using a λ/4 receiver coil and with the simple circuit (video 2) I am hitting the phase with current (not impulse). As a result i have much more power at the output than the input. Not so much as Ruslan has, but it can demonstrate the unusual effect of the standing waves. You can build it of yourself to see the effect. The only problem is to resonate well the two coils. (It takes time). Right now i am working on this project and i am using other frequencies (lower) to utilize the output, just to demonstrate it better. I hope i will show it to all of you soon! Regards.
Hey mr g thanks I have a question im not too much an electronics man but if I follow schematic will it be possible to get same results?? I only have one posting to you tube and thats all my experience but I understand a lot about frequency and hv and relationship to over unity from the vacuum.
Dear Alex see well first all 3 videos of my project. Check the circuit of nr 3. If you understand what is resonance and follow my instructions, you can find 100% overunity!
Hi , I'm a newbie on cuircuts so I have a quick question. in your last video, are you using the kacher scematic or would power mosfet cuircut from earlier work better? thank you for your answer in advance
i did not see any power measurements , also no power factor information. You cannot just see over unity it must be looped or measured very accurately with power factor correction. Oscilloscope does not show power only voltage. Resonance is just more efficient no over-unity.
Hi again . I was thinking about what you said earlier on trying to lower the frequency. on some of the tesla patents, there is an ac cuircut on the primary side of the receiver. so identical coils to transmit and receive. he used the ac cuircut in line with the load on the receiver side. if you use 50-60 hz to step up and short it on the receiver, to step it down, do you think it will work? As for tesla patents. I grew up with Western education, they don't teach anything that's free at school on my end. I had to learn everything I know about tesla by research.i am originally from Turkey and I didn't hear about kapanadze untill after I left turkey.i wish I had the opportunity to meet him when I was home . now I have to replicate what he was trying to show years later...
Dear friend. Tariel Kapanadze has build his FE device using high frequencies of 12-30khz for resonance to product standing waves in a conductor. After that he used 1-2mhz to hit the peak of the current (Tesla coil). You can find it out reading his own patent! At the output of his device there is a converter to 220v/50hz (also written in the patent). 50 to 60 hz is not working like this! (you can try it if you wish). If you want to build a working device, i recommend you to read Tesla's patents of high frequency high current. Then check again my videos or Ruslan, Akula's one. You have to build standing waves at the 2 coils (Kacher and receiver) and tune them to resonance. If you do only this step right, then you can get the picture of what is happening! Kapanadze kept it secret from all of them they reached him before. You don't need him to build such a device. Just understand Tesla's patents and keep your mind free and open!