Тёмный

Riding Mower Mulching Blades Review - Do They Work? 

John Salt
Подписаться 54 тыс.
Просмотров 75 тыс.
50% 1

Riding mower mulching blades review - do they work? If you're asking yourself this question, you're not alone. I've been wondering if mulching blades work after being disappointed by the performance of the riding mower mulching kit I got for my John Deere. It's review & test time.
I finally decided to purchase a set of these aftermarket MaxPower / Gator style mulching blades to compare against factory OEM blades - both standard factory blades, and mulching factory blades.
The results of these MaxPower riding mower mulching blades were fairly good. In fact, they exceeded my exceptions given the poor results I was getting with the factory mulching blades that came with the John Deere BM21816 mulching kit on this lawn tractor.
As with all mulching blades, results will vary. The main factors that determine how well (or poorly) any mulching blades & kit work, over & above the blade design, are:
- How long the grass is between cuts. The longer the cut grass blades are, the less likely they will get mulched up as fine as needed.
- How wet the grass is. If too wet, the mulched grass blades stick together like a snow ball and leaves clumps.
- How thick the lawn is. You have to cut more often or at a slower pace if you have a really thick & healthy lawn.
- How fast you mow. Slow your pace if clumping is noticed.
- Using deck plugs helps ensure grass is "chewed up" more for a better/finer mulch and is blown back down into the lawn instead of sitting on top of it.
Why do I mulch my lawn? I first started mulching after moving to an acreage because bagging was just too time consuming with the amount of lawn I have to mow, not to mention where to put all the bagged grass afterward. However, after mulching for eight years now, I've found other benefits. I usually only have to fertilize once a year now which is saving time & money. I don't have to water the lawn as often again saving time and money. Weeds are also down - you guessed it - saving time & money.
Link to the 42" John Deere MaxPower mulching blade set I used in this video:
amzn.to/2ZSOexF
Other MaxPower mulching blade sets are available for different size & brands of riding mower decks as well.
Video Chapter Time Index:
- 0:00 Introduction
- 1:34 How do mulching blades & deck plugs work
- 2:53 MaxPower mulching blade design vs. factory blades
- 5:16 Honda pushmower mulching performance (bench mark)
- 5:27 John Deere standard factory blade performance
- 5:56 John Deere mulching blade performance
- 6:07 Checking & balancing MaxPower mulching blades
- 6:50 MaxPower mulching blade performance
- 7:00 Mulching blade comparisons on lawn
- 9:26 Conclusion
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting RCHelicopterFun.com & my channel which helps me keep creating content.
Please consider giving a thumbs up & subscribe if you enjoy my content - thank you.

Наука

Опубликовано:

 

25 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 101   
@Rchelicopterfun
@Rchelicopterfun 4 года назад
Link to the 42" John Deere Deck MaxPower mulching blade set I used in this video: amzn.to/2ZSOexF
@indermannsingh1189
@indermannsingh1189 2 года назад
Will these blades fit John Deere S100?
@ciphercode2298
@ciphercode2298 2 года назад
You went through alot to make this video. Best,most in depth video I've found on the subject, thank you.
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Glad you enjoyed it
@mktwatcher
@mktwatcher 2 года назад
Thank you for taking the time to do such a good test. I Just saw these new blades on Amazon and was skeptical until I found your review.
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Glad to help
@dwoodog
@dwoodog 3 года назад
Thanks for all that work you put in to making this video.
@FurHeavensSake
@FurHeavensSake Год назад
You are so welcome, John, I told several of my neighbors of your time and energy spent, on our behalf and benefit, what was most admirable. I would like, but don't expect, everyone to be as helpful as you, but that just makes my ''thank you' more valid."
@christinaannabel
@christinaannabel 2 года назад
Thank you for the thorough comparison. We are weighing a variety of options, and your information is very helpful.
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Glad it was helpful 🙂
@joselitomontalban7762
@joselitomontalban7762 2 года назад
This is helpful. Showed how to properly install the MaxPower blades that I had gotten and also confirmed that they were a good choice. Thanks!
@jmabs5096
@jmabs5096 2 года назад
Easy to remember is grass grows UP, Blade wings go UP!
@FurHeavensSake
@FurHeavensSake Год назад
Well done presentation, informative, and appreciative of this efforts to 'show and tell' so I could understand it! Kudos!
@Rchelicopterfun
@Rchelicopterfun Год назад
Appreciate the view 🙂
@ruddyrid
@ruddyrid Год назад
Great back to back comparison!!!
@ElHobbito
@ElHobbito 3 года назад
fantastic video. thank you for the hard work!
@Rchelicopterfun
@Rchelicopterfun 3 года назад
Glad you enjoyed it
@southrocket
@southrocket 3 месяца назад
Thanks very much for this video. You are to be congratulated for such a through job. Plan to order some MaxPower blades for My Ferris Zero turn.
@Rchelicopterfun
@Rchelicopterfun 3 месяца назад
Mowing & mulching fun. Hope the MP's work well for you too - thanks for watching 🙂
@dbwright69
@dbwright69 Год назад
you helped me make up my mind to purchase special mulching blades. I recently purchased a jack that uses a screw mechanism to tilt the entire mower, and for just under a hundred dollars it sure beats the hell out of having to take the deck off.
@danielreasor6487
@danielreasor6487 20 дней назад
Where did you get the jack
@Johnny-bx7tb
@Johnny-bx7tb 2 года назад
Great video. Lots of work is obvious put into this. Thank you for this information
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Thanks for watching!
@Paulog1990
@Paulog1990 3 года назад
Can you please do a video on your lawn? Like type of grass and what you do to maintain it. It looks amazing.
@kennethlowe6337
@kennethlowe6337 2 года назад
Good info on the blades got some for my old cub they work great. You really have to get a mower jack combined with a impact 5 minute blade change now the only time my deck comes off is to blast and paint. 👍🇺🇸
@rudolfthegardener6105
@rudolfthegardener6105 5 месяцев назад
Great video. Thank you for all the effort
@Rchelicopterfun
@Rchelicopterfun 5 месяцев назад
So nice of you 🙂
@petersack5074
@petersack5074 2 года назад
9:50 time; Correct, John. I have several push mowers, one 6 hp one with the very same 3 tooth mulch blade on it. It is painted yellow, a different brand, but works just like these 2 you tested. Cutting a 15 inch high abandoned yard, and hardly any '' evidence '' of the cut-grass. The neighbor cut his 'hayfield ' with a riding mower, and wow....what a mess. It never had any mulch blades on it. What a huge difference. Anyway, thanks for the work, in educating us. Take care of all in your power.
@nicklloyd9165
@nicklloyd9165 Год назад
Thanks for doing this!
@blindbob2539
@blindbob2539 2 года назад
gorgeous lawn
@mattp9932
@mattp9932 8 месяцев назад
Great video. Ty
@Ed-ym4tu
@Ed-ym4tu Месяц назад
Appreciate the effort!
@Rchelicopterfun
@Rchelicopterfun Месяц назад
Appreciate the view 🙂
@goaheadmakeourdayscooterpe9644
@goaheadmakeourdayscooterpe9644 2 года назад
I never noticed a big difference in blades until used on dry leaves in fall the gator type and mulch blades really chop them much finer.
@99rvm
@99rvm Год назад
Great video,,going to order the max blades,you must have edited the part where you had a cold beer with all that deck removal,,,cheers
@Rchelicopterfun
@Rchelicopterfun Год назад
😄👍
@jascam1
@jascam1 2 года назад
Great video, the Honda HRX217 is a wonderful machine, six years running without a hitch and always start on first pull. Buy quality and you only have to buy once.
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Yep, can't beat a Honda mower. I purchased that HRB215 in 2000 so it's 22 years old now and is still working like a swiss watch with only yearly oil changes and I think I'm on my 3rd spark plug. Up to two pulls now to get it started so might be time to install the 4th plug... 🙂
@helenanderson4410
@helenanderson4410 2 года назад
Thank you, great video, informative with not too much old man ranting.
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Glad you enjoyed
@gerry7457
@gerry7457 3 года назад
very well done!
@Rchelicopterfun
@Rchelicopterfun 3 года назад
Glad you enjoyed it.
@jonathonmcdavitt92
@jonathonmcdavitt92 3 года назад
Great video
@Rchelicopterfun
@Rchelicopterfun 3 года назад
Glad you enjoyed it
@wheinz574
@wheinz574 Год назад
I plan on just purchasing the mulch kit insert along with the max power or predator mulching gator blades.
@rayburnett3253
@rayburnett3253 3 года назад
I have those mulching blades on my Poland. It's a 42 inch now. When I got the Poland it had a 38 inch deck on it with the star pattern on the blades
@jimjam1719
@jimjam1719 2 месяца назад
if you don't mind me asking, what deck are you using? actual poulan or husquevarna? i have a 38" poulan, needs a new deck, pretty worn out, was looking to upgrade to a 42 if it will work and what belt to use with it. i was thinking since poulan is no longer around, at least here in my area, maybe a husky deck would be interchangeable as in bolt on product without modifications.?. any advice would be appreciated. thanks.
@wurly164
@wurly164 2 года назад
I have a JD with the 42 cut, I got it with the bagging kit and also a set of mulching blades. I quickly went to mulching, but was never super impressed with its mulching. The guy put the wrong blades on, all this time I've been using the wavy blades for mulching. I'm looking to upgrade my blades so your video helps I also don't remove the deck, I just jack up the front and use an impact gun. Blades on in 5 minutes
@danbasta3677
@danbasta3677 2 года назад
Just be sure you do stick a stump of wood underneath just in case. Safty has no quitting time.
@wurly164
@wurly164 2 года назад
@@danbasta3677 I use a jack and always jack stands Belts and suspenders
@tommoretti666
@tommoretti666 2 года назад
Great video. One caveat I would add is the speed at which you ran your John Deer tractor. Did you move at the same speed as the Honda push mower?
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Hi Tom, I do mention pace in the description playing a roll in how well or how poorly mulching works; but yes, I tried very much to match walking pace.
@DwanHall
@DwanHall 3 года назад
42" deck on Husqvarna "0" steer. I took the same Maxpower blades and welded 2 of them in a cross for each side. My clippings are all less then 1/4" when cutting 2" of the top of heavy grass. I do find they create a heavy load when engaging the mower deck but I think it is worth the results. Been mowing with this setup for 2 years now.
@Rchelicopterfun
@Rchelicopterfun 3 года назад
Thanks for sharing your experience with them - interesting idea pairing them up like that. 👍
@petersack5074
@petersack5074 2 года назад
wow.....i may attempt to do the same feat, on one 6 hp push mower i got....thanks.
@garypic4083
@garypic4083 Год назад
Thanks Do a leaf clean up
@apaul13150
@apaul13150 2 года назад
I've got a mulching kit on this mower, I've had it for several years. That mower looks brand spanking new to me, you must look after it really well.
@Rchelicopterfun
@Rchelicopterfun 2 года назад
@Apaul - Yep, I look after all my stuff - makes it last longer and a penny saved is a penny earned. I purchased that little Honda push mower shown in the video back in the spring of 2020 so it's going on 22 years old now and still runs & looks great.
@apaul13150
@apaul13150 2 года назад
@@Rchelicopterfun buy good quality, look after it properly, it will last forever.
@SulaimanTheGardener
@SulaimanTheGardener 11 месяцев назад
The forks may have sharp edges to help shear grass but there main purpose is to direct air upwards which creates an vacum affect to lift grass upwards so it can be cut.
@rhornwhitside2068
@rhornwhitside2068 3 года назад
Where did you get that blade balancer ? That looks way better than the stupid cone ones I have. Love the content . Think I'll get a set of those blades.
@Rchelicopterfun
@Rchelicopterfun 3 года назад
It's actually an RC airplane prop & RC helicopter Blade balancer (I fly RC helicopters) that I also use for checking mower blade balance. It's called the Du-Bro Tru-Spin balancer. amzn.to/2TuAit0 One caveat if you get one for mower blades - you will have to make some sort centering hub for the blade hole and the coned prop shaft (the white thing you can see in the middle of the blade hole in the video).
@AuronFFX
@AuronFFX 2 года назад
I've always used a screwdriver through the hole hold it straight and the blade will tilt to whichever side is off balance.
@lopincol
@lopincol 8 месяцев назад
Very good video. Please try the original Gator blade from Oregon. They're the best on the market. Get the G5 or G6 if you can
@joeedmond7715
@joeedmond7715 Год назад
Noticed that the angle on the gator blade you used looks like it pushes air out from the blade centre. Other gator blades, from Oragon I think, angle the blades to push air and clipping in toward the blade centre. Apparently this is to allow the cutting portion of the blade to repeatedly chop clippings into smaller pieces. Could be the reason for the poor performance???
@dogrescuer1321
@dogrescuer1321 3 года назад
Nice video, I'm interested in converting my riding mower to a mulching machine what else is needed besides mulching blades please?
@Rchelicopterfun
@Rchelicopterfun 3 года назад
As I said in the video, you need a mulching plug as well for your specific deck. So that's all you need the blades and the plug.
@dogrescuer1321
@dogrescuer1321 3 года назад
Thanks for taking the time to answer.
@StewPudasoe
@StewPudasoe 25 дней назад
I have a mower with mulching blades on it with the chute closed! Do I have to close the deck as well? Or does it just mulch it and spit out nothingness?
@MsVictory1945
@MsVictory1945 2 года назад
Do you have to buy the mulching kit AND the mulching blades or can you mulch with just the mulching blades? I have a JD LA105. Thanks!
@Rchelicopterfun
@Rchelicopterfun 2 года назад
As I said in the video, mulching plugs are an integral part of a mulching system. Mulching blades only work as intended when the grass clippings are circulated within the deck and not immediately blown out the side or back.
@PERRAS239
@PERRAS239 4 года назад
Do you think these blades will help from cutting a lawn with weeds from carrying them over to the next?
@Rchelicopterfun
@Rchelicopterfun 4 года назад
I wouldn't think so unless you were to totally clean the deck of grass/weed/seed buildup between lawns.
@fastmoparr19791973
@fastmoparr19791973 Год назад
Credit to u sir I hate taking the deck off
@Rchelicopterfun
@Rchelicopterfun Год назад
You and me both 😬
@jazpanoz4996
@jazpanoz4996 4 года назад
If your mulch cutting,you need to mow slower in passes than you normally would to get best results,I found😉
@Rchelicopterfun
@Rchelicopterfun 4 года назад
Yep, it's one of the items I mention in the description on what affects quality of mulch.
@barbaravial6244
@barbaravial6244 2 года назад
I have the gator blades on my John Deere x570 .The cutting is ok BUT the build up of clogg under the deck is horrendous. So much so the deck belt jammed and broke. It takes me as long to get under the deck to scrape away the build up ,as the actual mowing. Help
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Grass needs to be fairly dry and not too long when mulching for best results and to keep it from sticking inside the deck. You can also try treating the underside of your deck with something to prevent the grass from sticking to it. I use Boeshield T-9 once a season and it works great. I've heard others recommend car wax, furniture wax, ceramic coat, cooking spray, silicone spray, wiping it down with transmission fluid or motor oil etc. If the grass is really wet however, no amount of anti-stick coating will keep it from sticking & building up.
@perrooceaniko2005
@perrooceaniko2005 3 года назад
Nice 993 ....😘😘
@brianspindler204
@brianspindler204 2 года назад
Can you use these without the mulching plug? Will it still cut more finely?
@Rchelicopterfun
@Rchelicopterfun 2 года назад
They will chop up the blades finer, but not to the same extent they would be with the plug in place because the clippings will be discharged much quicker than if they are kept circulating within the deck. It won't be much different from just side discharging with normal blades in other words. Mulching blades are meant to be used in conjunction with mulching plugs for them to work correctly.
@brianspindler204
@brianspindler204 2 года назад
@@Rchelicopterfun thank you for your information 👍
@RiseOrRelinquish
@RiseOrRelinquish 3 месяца назад
Which way do they get installed? I Believe I see the little ripples pointing upward toward the deck
@Rchelicopterfun
@Rchelicopterfun 3 месяца назад
@6:45
@elit3401
@elit3401 3 года назад
Yes , they do work. If you keep going over and over the grass left on top will ultimately be put down into the ground and leave a nice clean cut lawn. Oregon G3 or G5 mulching blades do the best. Nice video, nice lawn.
@Rchelicopterfun
@Rchelicopterfun 3 года назад
I've found over the past year now, I've never have to double pass unless I leave the grass too long between cuts, or it's too wet. The only thing I don't like about these maxpower mulching blades as much as the JD mulching blades that came with the mulch kit is they do seem to have less suction. Last fall, I found they (the maxpowers) didn't lift leaves off the grass as well to mulch them and for that specific leaf mulching job, a second pass or very slow speed was indeed required. That is the one area where the original factory mulching blades definitely have the edge (pun intended). 🙂
@danbasta3677
@danbasta3677 2 года назад
Best to not cut your grass with the mower deck down to the lowest level on your tractor. Raise your mower deck up and allow the RPM's do their job on cutting and reciting the grass down to small particles, or residue on grass. I do have a push mower which is a mulcher mower, and the setting of it is up in the middle between high and low, and after cutting the grass with it, you see nothing at all by way of grass shavings.
@Condor1970
@Condor1970 11 месяцев назад
Why the heck does my mulching blade with little fingers sound so loud? When it gets a lot of grass underneath and recirculates to mulch, it sounds like its rattling really loud. Yet, the blade is solidly mounted and the engine rotor/shaft is solid as well. It just clanks and rattles like crazy. It does a fantastic job mulching though.
@Rchelicopterfun
@Rchelicopterfun 11 месяцев назад
I experience similar (whole deck vibrates/rattles), but only when the grass is wet or overly long; basically clogging up the deck faster than the blades can chew the grass up and blow it back down. Not sure if that's the same thing as what you're experiencing or not, but to stop it on the little JD I have, I just have to go slower or raise the cutting deck and do two cuts.
@Condor1970
@Condor1970 11 месяцев назад
@Rchelicopterfun ...That may be it. Here in PacNW, our grass grows a couple inches or more a week. I noticed initially it sounds great, but as you hit a thick spot and clippings build up under the deck, it gets really loud, like it's grinding rocks with a tuning fork. If I slow down, it goes away slowly until it's mulched up into very fine bits, with virtually zero clumping. Maybe it just requires mowing twice a week instead of only once.
@mattp9932
@mattp9932 8 месяцев назад
What’s the negative of ALWAYS using mulching blades. Even if you bag
@Rchelicopterfun
@Rchelicopterfun 8 месяцев назад
They (mulching blades) produce less suction to move the clippings into the bag. For spring cleanup with the Honda push-mower for example, I always refit the regular blades as they do a much better job of sucking up all the crap into the bag.
@pickin4you
@pickin4you 8 месяцев назад
Why in the heck would those forks clog? The grass is going over the top of those. The cutting side is on the other side of the blade. Those are air lifts to lift the grass up that has been cut so that it can cut it again. So clogging? No way. That should have not even been a thought.
@Rchelicopterfun
@Rchelicopterfun 8 месяцев назад
Of course they could clog in the right conditions with the right kind of grass. And no, the grass is not going over those forks, *it's interacting with them*. They are what help chop it up finer as I stated. Yes, the forks most certainly can clog and they have clogged; clogged absolutely solid when I once had to mow long wet grass. Of course you should never cut long wet grass ( *especially when mulching* ), but sometimes life & poor weather get in the way forcing you to mow in less than ideal conditions. So that's absolutely one specific example of "why in the heck would they clog". There are more.
@mattg4306
@mattg4306 2 года назад
Original factory deck looks like it also sits lower than the others
@Rchelicopterfun
@Rchelicopterfun 2 года назад
Original factory deck/others? It's the same deck & same height for all 3. Only change was the three sets of blades.
@Jimmy-Legs
@Jimmy-Legs Месяц назад
Probably have much better performance if you knocked off all that stuck on grass.
@Rchelicopterfun
@Rchelicopterfun Месяц назад
Nope, makes no difference.
@Jimmy-Legs
@Jimmy-Legs Месяц назад
@@Rchelicopterfun Be interesting to see how it performs without the mulching thingy in there.
@Rchelicopterfun
@Rchelicopterfun Месяц назад
Not well. The grass all gathers and clumps badly on the discharge/outlet side of the deck (the right side on this specific deck). With wet grass/long grass, it will actually clog that side of the deck up so badly without the mulching diverter, the belt will actually start slipping on the blade spindle pully (at least on this machine it does).
Далее
Gator Mower Blade Comparison - BEST LAWN MOWER BLADES
8:30
Mulching Vs. Bagging? What Should I do?
9:35
Просмотров 158 тыс.
Best Toilet Gadgets and #Hacks you must try!!💩💩
00:49
Best Lawn Mower Blades - Types, Usage, Differences
12:37
John Deere Mulch Kit vs Gator Blades | Z540R
7:35
Просмотров 143 тыс.
The Truth About Mower Spindles
12:15
Просмотров 959 тыс.
Новодельный ноутбук Pocket386
1:16:17
Новые iPhone 16 и 16 Pro Max
0:42
Просмотров 956 тыс.