Round Wing Zipper Pouch | Detailed Sewing Tutorial 

Learn to sew your own Round Wing Zipper Pouch in this detailed sewing tutorial.
If you have any questions along the way, you can direct message me on instagram (@torieandren) or comment below and I will try my best to answer as soon as possible. For pattern updates or corrections visit my instagram and check my story highlights.
For written instructions visit: torieandren.et...
Instagram: @torieandren
Templates can be found here: bit.ly/3RDFCps
The seam allowance for this project is ¼”. Seam allowance is indicated at each step.
Finished Size: Approximately ≈ 5¼” × 5¾”
Materials:
Faux suede/leather vinyl is recommended for Print C. Other materials such as quilting cotton, cotton linen (55% linen and 45% cotton), and 21 wale (21W) cotton corduroy can be used for Print C. A lightweight fusible fleece is recommended to reduce bulk which will help keep the bottom round when turned inside out.
You may require other supplies such as snap pliers/fasteners or a press, pinking shears, scissors, pins, a rotary cutter, thread to match your fabrics, and a ruler or measuring tape.
Materials (Yardage)
Print A (Quilting Cotton): Fat Eighth
Print B (Quilting Cotton): Fat Eighth
Print C (Faux Suede/Leather): Fat Eighth
Print D (Quilting Cotton): Fat Eighth
Lightweight Fusible Fleece (Pellon 986F or similar): ¼ yard
Continuous Nylon Zipper #3 or No. 3 or Size 3: ¼ yard with 1 Zipper Pull Cut to 5¾”
12.5mm or Size 20 Fashion Spring Snaps
Materials (Scraps)
Print A (Quilting Cotton): N/A
Print B (Quilting Cotton): (2) 4” × 6½” and (1) ≈ 1” × 2¼”
Print C (Faux Suede/Leather): (2) 2¼” × 6½”
Print D (Quilting Cotton): (2) 5¾” × 6½”
Lightweight Fusible Fleece (Pellon 986F or similar): N/A
Continuous Nylon Zipper #3 or No. 3 or Size 3: ¼ yard with 1 Zipper Pull Cut to 5¾”
12.5mm or Size 20 Fashion Spring Snaps
Cutting:
Print A (Quilting Cotton)
(2) Bottom Template
(1) Pocket Template
Print B (Quilting Cotton)
(1) Flap Template (Template facing up)
(1) Flap Template (Template facing down)
(1) 1” or width of zipper × 2¼” Zipper Tabs
Print C (Faux Suede)
(2) 2¼” × 6½” Exterior Accent
Print D (Quilting Cotton)
(2) Lining Template
Fusible Fleece
(2) Bottom Template
(1) Flap Template (Cut with the template and glue side of the fusible facing up)
(4) 2” × 6½”
(1) 2” × 2”
Materials used in this video:
Fabric:
Print A is Little Fawn and Friends by Nina Stajner for Dear Stella
www.hawthornes...
Print B is Countryside Comforts by Jane Carkill (LambLittle) for Figo Fabrics
Print C is faux suede bought from sewersclub.com in store.
Print D is Little Fawn and Friends by Nina Stajner for Dear Stella
www.hawthornes...
Interfacing:
Pellon 986F OR 987F
sewersclub.ca/...
sewersclub.ca/...
Hardware:
Zipper & Pull: sallietomato.c...
Snaps: I can't remember where I got my snaps, but KAM snaps has some kamsnaps.com/c...
I am affiliated with and have personal ties to Sewers Club and Owl Be Sewing, but do not make a commission off the products I recommend or share. My opinions are my own and I share products because I love them. I do get items at a discount unrelated to Torie and Ren videos and patterns.
Thanks for stopping by, I hope you love this project just as much as I do.
with love,
torie and ren