RUSTOLEUM PAINT JOB 

The reason people are using spray cans isnt because of the cost of the material, its because of the cost of good equipment. larger compressors, air filtration, (good) spray guns are expensive. then you have to know how to use them, and mix the paint and hardeners and thinners, which tips to use, how to dial the air and the fluid. When a paint shop charges thousands for a paint job, the material cost is almost immaterial to the process. People use spray cans because they dont have the equipment, they dont know how to mix anything or use the right tip or dial the air or fluid, you push the button and paint comes out. so that $90 vs $120 base color comparison makes spray paint not make sense for you. but you have thousands in equipment, and years of experience laying paint. Anyone can pick up $150 in spraycans from home depot, and if their prep work is good, they can get decent results. Add in about $250 for those 2k clearcoat cans and you can get a better than factory Toyota paint job for Maaco price. If you or a buddy has a DA polisher and know how to use it, you're can take that clear coat close to a good factory American/European car paint job.

I have Barcelona Red Toyota, the base cost was $200 for a pint. I went to Autozone bought 4 Duplicolor rattle cans for the hood and roof for $25. Flipped the cans upside down ran the aerosol out, pierced the cans poured directly into my Sata and sprayed then cleared it, perfect match and looks beautiful . The key is get the paint out of the cans and into the sprayer cup. Had left over paint when I was done.

I’ve seen raddlecan paint on some vehicles! This is by far the best I’ve seen! The clear coat definitely did the trick!

I did 2 fenders with a spray can and said enough of that noise.. got some (quart) enamel custom matched to the spray can color for 22 dollars. Added hardener and thinner and some japan drier and shot it out of a HF gun and came out great..wet sanded and buffed it for a day about a week later came out great. So an alternative to spray cans. We will see how long it lasts. Great vid!

As a finish carpenter who uses an hvlp turbine to spray trim and moulding, I am amazed at how much overspray occurs with your gun. Clouds and clouds. Then again, spraying thinned water base latex is a whole different beast.

I had an old 07 gmc duromax 4x4 with a half million miles on it, that I used to run my trap lines. Drove it thru the brush and had so many scratches on it, that would've taken forever to sand it out. Got the bright idea to black rino liner the whole truck. So I ordered a few kits thru Amazon. Came with it's own gun and everything. It ended up awesome! And that stuff was tough as nails. Almost impossible to mess it up.

Best rustolum paintjob on youtube, most others use spray can for clear

I am professional body man, and back in the day I was selling an Acura Integra with a new fender on it. The buyer wanted me to spray paint the black e-coat fender in spray paint just so it had some color on it. I picked up some Krylon semi gloss white, and it matched perfectly! I ended liking it so much I cleared over the spray paint and kept the car, it lasted 6 years before the clear coat started to peel. The clear coat peeling was because I didn't remove the belt molding, so my fault. The spray paint as base was legit!

I am a mobile autobody man or a backyard mechanic as you would see but I take pride in my work before I do any paint job. I wash every vehicle with Dawn dish soap, reason being like you said it gets rid of all the dirt cleans everything and the dish soap decreases everything.

You guys inspired me to paint my car like this and y'all did an A1 job thanks for making this video 🔥🔥🔥💯💯💯

My 91 honda Civic is this color. Used the gloss cans. Never cleared it, but I'm really thinking about it for the longevity of the paint. I do keep it clean and ceramic coated . Definitely love this color

Wow that Celica came out really really good!!!! I have 2 Celica GT's and also put a lightweight flywheel and performance clutch!!! Glad I did

I always have problem with rust oleum brand paint aerosol cans. Seems like half way through it loses air pressure. So now I see that you can refill the air pressure in can with a car rim air valve. WOW that clear coat really made it look good!👍

MY MAN WOULD YOU PLEASE TELL ME HOW LONG TO WAIT UNTIL SPRAYING THE CLEAR AFTER PAINTING THE CAR? You da man

people hate on it, but I love rattle can paint jobs, gloss black, on a old rusted out work truck I use for my lawncare business every 6 to 10 years, keeps her looking pretty decent for the age. especially with these midwest winters not being kind to dodge ram bodies lol.

My fingers were cramping just watching you guys use those aerosol cans 😆. Rust-Oleum actually sells a nice spray can handle called a Comfort Grip, #241526. Works great. Thanks for the video 👍🇺🇸

Dam bro that came out clean af, Excellent job as always 👌

Very informative thank you. I can see where this would be a lot of fun with a good running old car!

So I’m here in the garage . Once you were done dropping that glass I put the phone down and was just listening . I had to come back the min I heard you do that “ negative RU-vid viewer comment voice “ . …. Good laugh brother . Keep dropping that glass man …….

Celica looks amazing brother. Thank you for the video

I painted my ugly brown 79' Dodge beater pickup truck with 15 cans of $.98 Walmart gloss black one summer. I washed it, hit it with a scotch brite pad, washed it again and masked it off. I have to say it actually looked pretty decent! Much better than oxidized turd brown anyway. It held up for several years of Oregon weather before is started to get thin and the brown started coming through. These days it's parked and hardly used. It looks almost tiger striped from fade between the spray pattern.

I did a rustoleum turbo can paint job on my 93 silverado in 2019 waited 3mos wet sanded an cleared it in my back yard, man-o-man it still look like it came out of a gun!!

👀👍🏽 not bad. I've never rattle canned a car but I've done small parts so for that to come out looking so respectful I'd say another win🏁🏁🏁

Great job, If you told me this car was painted with spray cans I wouldn't have been able to tell.

I love the memes,. A new thing I hear in this generation is they use turbo paint cans and 2k clear with that activator. I'm new to the paint warming thing and the paint prices got crazy It exploded in the last few years

Id pick up some of those little pistol grip spray can handles. Makes it easier to hold a trigger in than pushing those buttons.

How about mixing brands... like A brand singel stage - use B brand of clearcote.... What should I think about of what can happen? Really nice job....but you should take of the wing.....🤔🤔🤔😉😉😉😆😆😆

I used the rustoleum in the gallon with the majic hardener. It wasn't horrible but even a cheap base like crossfire sprays better

Dude what amazing looks that color i really love it

Looks great! Considering a Rustoleum paint job on my budget hot rod build. Got a bit of rust repair to take care of first though.

I painted my truck sunrise red from home depot and won a truck show...do the dam thang Playa

Man love it I miss those rattle can days in the earlier videos I know you and bens fingers was tired after the 13 cans of paint 😂

can you make a video discussing the benefits of sanding primer before paint? thank you.

I don't care what anybody says that looks great 👍👍 Nice work 👍

I enjoyed the video, keep them coming. Thank you.

WOW le queda perfecto ese color !!!! excelente trabajo !!!

I'm surpised you didn't get the Spraycan Gun handle to help with the paint process. OTHER THAN THAT! I love this!!!

you have a whole entire paint booth that's ventilated and all that - you got your tyvek suit on , good ventilator mask - but yet your using rattle cans? Its almost like invading Normandy with bow and arrow? ...doesn't work out in the end. Just do it the right way brother man!

Three cans for $20? In Canada manufactures raised the price from $6 to $15 for one can!

Having done the Rusto, I forget how many cans I did end up going through on my small car, but I'll say it was around 8-10, and my Sentra was smaller than that Celica. That doesn't count primer cans, either. So I think you're right on that estimate, especially because I think your primer was probably very porous, whereas I think the Rusto "filler primer" was less porous. I think the advantage of doing it the spray can way, even if you can't justify it completely in dollars and cents is that with rattlecans it's much easier to go panel by panel during 1-3 hour kinda stints after work or whatever, and just do a fender or a door at a time, and eventually after a few weeks or months have the whole car done. I wouldn't do "two coats" but I would do about 3 passes, first pass really light, and second and third passes progressively heavier. Also what I did to eliminate the tiger stripes was since I was spraying outdoors, I would wait until just around dusk to spray, when it would be coolest. I would never spray mid day. I ended up getting rid of that Sentra sadly, but I do want to do it again, and hopefully do it panel by panel as I said and then one day with a gun get some of the nice Speedokote clear and do it up really nice. You are right math-wise, but having to do the whole car in one shot is pretty hard.

Looks great with the clear coat, Just wish you would have done it with Rusto clear to make it a 100% Rusto job but still came out really nice.

Please show it all toghter, thts the iceing on the cake for the ending!!!!! Great work as usually but we as fans need the whole car together!!!!!!!!!!😢😢😢😢

This isn’t your typical rattle can spray job by some kid . They don’t have access to spray guns for primer and clear coat so this is going to come out way better than anything they could do!

One option is to plan ahead and order the paint....also one can here $15

I like it. Back in the '80s, I tried rattlecanning an old Cutlass with acrylic lacquer and no clearcoat. Actually it was Duplicolor Bahama Blue metallica....( Ain't My Bitch ) 😆 I was experimenting with cut and buff.....it was okay....wish I could've had pictures of it. That was when you had to actually buy film for a camera! Damn....I'm older than dirt! There was no RU-vid then!

why wouldn't you get a quart ($16) of that color instead? all you have to do is thin it out and spray it with a real paint gun instead..

I feel like you hold the gun/can too close to the surface, makes me nervous, but the results speak for themselves!

Hi..I used acrylic lacquer paints and when i put polyurethane clearcoat the result was that my clearcoat peeled...so must I sand my paint before putting my clearcoat...tanks

Great job, thank you!

You shouldn’t put bondo overpaint and, if your going to put bondo over paint, get t rough with 80 grit, and, you don’t want to get water on bondo, it soaks up water like a sponge

More secrets about paint temperature and panel temperature released! Y'all better be taking notes😂. Came out minty fresh bro 😎

looks much better with the clear applied. 120 versus 90 ,definitely go 120

Wow! Great job. Have you made a video showing how to remove a vinyl top and prep for paint? My 1984 olds cutlass needs its top removed due to hail cracks!!

i guess the major question is how does it hold up? anyone with it after a couple of years of harsh summer sun? ,,really is interesting it works being an uncatalized color but so is regular water bourne as well as solvent basecoat,very interesting ,,thanks for posting

My husband has been doing paint and body work for 20 years and he never takes the wings off of a car and has never used a paint booth and there is little to no debris in the paint.

Looks great 😎👍🏾

Great results! I've always wondered. What do the door jambs look like?

Man that looks way better than the job a guy did my wife’s mustang using a gun to paint it. Wish I had a shop I would have spray painted the car myself for way cheaper than the $3k he charged us to ruin our car

I found out last week when I git bored you can use smr42 over krylon spray paint, I used my fathers wheels as a test mule because he didn't believe me lol.

Good video having fun looks good

Great job Love the lesson in all your videos Please keep up the good work

did you use a specific primer and or sealer? love the content!

I not a professional but have painted a car on the cheap before and yours came way better ! That said maybe just me and everyone else know, but I saw some orange peel in the clear when you were spraying. Did you cut and buff it and I'm just suppose to know everyone finishes that way or does your clear coat level out as it settles on the car ? Because O can't see buffing that out on such a cheap job and the finish pictures it didn't look like the orange peel was there ? just wondering because you said you sell the clear coat !

If you have the equipment to spray (compressor and gun) wouldn’t it be better to mix rustoleum paint, acetone, and a little hardener instead of using rattle cans?

I can’t wait to bring you my 96 Acura Integra, to do a paint job on it, love your work 🔥🔥🔥🔥🔥

car looks good,but why not turn the cans upside down and empty the gas out of them..open them up and pour the paint into a regular spray gun?...i would like to see the car outside..nice color on it

I have a lot of respect for you my brother

So the clear coat goes on right after the painting or can it go on at a later date? When do you cut and polish? I have no experience but i hear it here all the time. Cut and polish

Just saw on facebook a guy who painted his car with $700 worth of UPOL cans. I cant imagine spending all that time prepping a car amd using cans.

MAN, i got paint yesterday at advanced auto....15 BUCKS PER CAN!! INSANITY!!

I love it that you do in depth videos on the Rustoleum and shop grade stuff. There is so much you can do with these basic paints. I’ve never attempted to clear a rustoleum paint but want to try. Do you find you have to let the color flash/cure before clearing or just spray clear when it’s dry?

How did you get rid of the tiger stripes? Does the clear blend them out? Painting a hood at the moment with cans and those stripes are killing me.

Looks like the old Earl Scheib blue from the 70's.. 🤣

Why so close to paint with the clear? Could have avoided the runs

Amazing paint job this turned out to be. Once u hit it with your clear it really woke it up. What air filtration system should I buy for my home garage to clean the air?

"Sometimes it's not your environment it's your air" Bill Nye the Science Guy 🙄

Not bad! But stick with what you know best Marco great video brother

Hit the rims the same way same color

I want to paint my roof and my hood a different color from what the car is with the rest of the car stay the same do I have to strip all the paint off and prime before I paint the hood and the roof or can I just scuff it up and spray it over with the new color?

show the car up close.

How do you feel about spraying rustoleum out of a gun?

Ouch...Sore fingers...😅 looks good !!

I have 2 gallons of the smr 1150 did under a hood with it pure garbage shits like water never again will i buy. i used half a gallon just to get the results i wanted nothing but a jam clear im tempted to just throw it in the garbage ive never seen such a hazzy clear when spraying

Wow, there's a lot of beating around the bush in this video. I'm surprised they didn't video their meals and trips to the can as well. Sheesh!

Great color

What kinda clear coat did you use? And also i long did you let the paint sit before you added the clear?

Hey so where on your setup did you install your new filter? My compressor feeds a 25' line to a 50' line - so 75 feet of hose - i was thinking right at the compressor. Would value your opinion. Also, you gave my hope that painting my cheaper projects doesnt have to be expensive. When I am spending $150-200 for half a pint of like honda pearl red or some crazy toyota color, easy to get discouraged thinking of a whole car job, but the cheap base and decent clear - maybe $250-400 total - would be just fine for say my 54 chevy truck I am throwing together. Thanks

Sometimes I will paint my old work trucks with a gallon of rustoleum, acetone, and hardener. Will that clear coat still work ok ?

I know you don't wanna make a living out of rattle....Why wouldn't you just buy the Rusto by the quart or gallon in white and have the big box add the color you wanted? What was the primer you used? What are your thoughts about getting tractor paint (Majic) with thinner and hardener for an old truck compared to Rusto? I know, if it is only a little cheaper, get Speedokote. Is it that much better for a car or truck compared to tractor?

Should have bought a quart of paint for $40.00 any color you want but still looks good.

Ready for some teeny bopper at $5-6K 😆 Keep em coming!! 🍻 🇺🇸

What on earth happens to a non catalyzed product under a catalyzed one lol. Bubbles, delamination, cracks asking for a friend lol

Cool video I painted my bug with the same paint . I just grab a quart and cut it then mix it with some flat clear and bam

Why would you paint with rust oleum. Thick paint will fail there’s a reason why automotive paint is applied thin

Amazing job.

looks great

Rustoleum is not too bad. They have some different spray heads.

Wait... Rustoleum is oil-based paint as I recall, so how are you clearcoating over oil-base?

Is it true that the prep work is way more important than the actual paint that goes on? That's just what I was told

i got like 3 cars i really wanna repaint back to OG colors.. i'm inexperience and scared that i'll do lots of uneven painting so you'll see lines of it lmfao..