RV Electrical System Solar and Lithium Battery Upgrade - Start-to-Finish Guide

EXPLORIST life Mobile Marine & Off-Grid Electrical

Подписаться 261 тыс.

Просмотров 148 тыс.

50% 1

This video will show you, start-to-finish, how we upgraded an existing electrical system in a 30A Travel Trailer.
In this DIY 30A RV electrical install, we cover a wide range of topics, so we have included chapters at the bottom of this description if you need to find a specific part of the install.
This comprehensive tutorial will cover installing a 270aH Battle Born GC3, wiring a Victron Lynx Distributor with a BMV-712 Smart Battery Monitor and master disconnect switch, replacing the lead acid battery with a battery relocation kit, installing 800W of solar panels connected to a solar charge controller, wiring a Victron MultiPlus 2k and splice kit so we can run 120V outlets without being connected to shore power, and alternator charging using Anderson connectors. Each chapter will also include a segment on programming and testing each component so you can best understand your system.
➤ Shop kits used in this video at the EXPLORIST.life Store: shop.explorist.life
➤ Shop Battle Born Batteries: battlebornbatteries.com/?afmc=...
✅Use code 'explorist' for $50 off per battery.
➤ Binge all our other full installs: • DIY Van, RV & Motorhom...
00:00 Introduction
00:36 OEM System Walkthrough
03:48 Electrical Upgrade Plan
04:16 Lithium Battery Install
04:49 Wiring the Lynx Distributor & Chassis Ground
11:52 Battery Bank Relocation
16:01 MultiPlus and Splice Kit Install
25:42 Solar Install
34:33 Alternator Charging
40:16 Final Thoughts
Here are some additional resources that you may find helpful with planning and installing your DIY Camper:
➤TRUCK CAMPER INSTALL: • How To Upgrade Your Tr...
➤ Binge the Transit Van Build: • The Ultimate Camper Va...
➤ FORD TRANSIT DIY Camper Van Electrical Install: • DIY CAMPER VAN ELECTRI...
➤ DIY Sprinter Camper Van Electrical Install - Full Tutorial: • DIY Sprinter Camper Va...
➤ DIY Camper Solar Wiring Diagrams: www.explorist.life/solarwirin...
➤ How to Perform a Power Audit: • How Much Solar Power D...
➤ Basic Parts & Components of an Electrical System: • Basic Solar Parts Need...
➤ How to Cut Wire: www.explorist.life/how-to-cut...
➤ How to Strip Wire: • How to Strip Wire from...
➤ How to Crimp Wire: • How To Crimp Wire Lugs...
➤ How to Make MC4 Connectors: • How To Make MC4 Connec...
➤ How to Wire Solar Panels in Series-Parallel: • How to Wire Solar Pane...
➤ How to Crimp Wire Ferrules: • How to Crimp Ferrules ...
➤ How to Wire an AC/DC Breaker/Fuse Box: www.explorist.life/how-to-wir...

Авто/Мото

Опубликовано:

26 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 435

@EXPLORISTlife 11 месяцев назад

❗❗ *IF YOU WANT A SYSTEM LIKE THIS:* ❗❗ *Here is the core kit:* shop.explorist.life/shop/all-products/30a-oem-rv-retrofit-2000w-inverter-200-1000ah-battery-bank-dc-dc-charger-wiring-diagram-kit/ *Also available with a 3kVA Inverter:* shop.explorist.life/shop/all-products/30a-oem-rv-upgrade-400-1200ah-battery-bank-multiplus-3k-12-orion-12-12-30-wiring-diagram-kit/ *And then you can add whatever solar you like/need from these options (12V battery bank options):* shop.explorist.life/product-category/all-products/camper-wiring-kits/solar-charging-wiring-kits/ Or... *Here is the EXACT setup we showed in this video:* shop.explorist.life/shop/all-products/travel-trailer-electrical-upgrade-270ah-battery-multiplus-2k-12v-800w-solar-orion-12-12-30/ *GET $50 OFF PER BATTLE BORN BATTERY WITH CODE explorist AT CHECKOUT:* battlebornbatteries.com/shop/brands/battle-born-batteries/?afmc=explorist_bb67

@bryansbusadventure4783 5 месяцев назад

I purchased all this before I found your site Sad but that is reality The reason I want to know about C rates is as I am a DYI person and want you to know build my own batteries Of course cost is a huge factor in this choice

@21trips 4 месяца назад

How much do you charge to install this?

@mikethomsen5096 4 месяца назад

can i do a 3000 w inverter instead of a 2000w for this system

@andrewhofmann5453 11 месяцев назад

I dont think you guys know how much we have been waiting for an RV related video that works for us all! This is great. Thanks!

@EXPLORISTlife 11 месяцев назад

Hey, @andrewhofmann5453! I appreciate that. Thanks for watching! 🙂😀

@mikesnifferpippets3733 5 месяцев назад

Agreed! I have learned so much by watching just a few videos… I feel like such a nerd 😂

@1gesteban 4 месяца назад

Why is solar panel wiring such a "thinner" gauge? Do they eventually need to be "thicker" with the more solar panels in use?

@sbramel93 2 месяца назад

@@1gestebanthe higher the voltage the thinner the wiring you can get by with because you size the wire by amps

@Swerly01 11 месяцев назад

I really hope you're on the payroll and get shares of Victron. You guys do an amazing job of explaining everything.

@briandumont7619 11 месяцев назад

This video is great! I'm almost done retrofitting my daughters 30 amp OEM system and this helped fill in some final pieces. Also, your wiring kits are fantastic. I have sourced most of my upgrade through you with excellent shipping times and accuracy. Great job!

@housesOTR 10 месяцев назад

I upgraded my Imagine 17MKE to 300 Ah of lithium, 3000 watt inverter, two solar chargers. Works very well. 370 watts on the roof and 200-400 watts portable. Great video. Glad to see you both in it.

@Chantheman235 11 месяцев назад

In the process of adding a Victron DC to DC charger in my trailer as well. Thank you for the excellent tutorials, they have been extremely helpful!

@ascenttev6022 11 месяцев назад

Stephanie has truly turned out to be an A+++ PRODIGY. Your tutorials has always been helpful, we appreciate your input.

@EXPLORISTlife 11 месяцев назад

Hey, @ascenttev6022! I appreciate that. Thanks for watching! 🙂😀

@scottd143 11 месяцев назад

What a great video. Your technical knowledge and explanations are priceless. Also your kits are easy to use for us DIYers.

@EXPLORISTlife 11 месяцев назад

Hey, @scottd143! I appreciate that. Thanks for watching! 🙂😀

@betterwithrum 4 месяца назад

Hey thank you for putting this video together! It is the most comprehensive video I've seen on going from zero to fully decked out. I have to figure out how I'm going to run power to the Multpass 2 and back to the fuse panel, but one problem at a time!

@chrisjohnson4110 9 месяцев назад

I could watch this stuff all day. Is it uncommon that I am contemplating a career change, so I can do cool stuff like this all the time? I've done a lithium battery and the 712 with inverter and new converter in my little TT so far, solely from the confidence and complete explanations of each step that you provide. Thank you Nate and Steph!

@cpwatching5647 11 месяцев назад

Excellent video for the 30A trailer folks like me. Appreciate the details...well done. I'm thinking about a game changer prep as I build my system. Thanks!! Take care.

@GirdHerd 11 месяцев назад

Another outstanding "how to" video. I purchased and followed your detailed diagram for a 3000w system a few years ago and the system is still working great. If I was doing an install today, I would definitely buy all of the necessary install kits from you to make sourcing easier. Keep up the great work.

@EXPLORISTlife 10 месяцев назад

Hey, @19ken49! I appreciate that. Thanks for watching! 🙂😀

@ghostpepperrides4805 8 месяцев назад

Outstanding. As a retired electrical/Mechanical contractor I understand most of this. The equipment is new to me. Thank you. I’m subscribed.

@tomwilliam5118 11 месяцев назад

You guys do a top-notch job. So clean so detailed is unbelievable

@EXPLORISTlife 11 месяцев назад

Hey @tomwilliam5118, Thanks so much! Cheers!

@paulmalone7323 26 дней назад

This was very helpful. Just purchased a Brinkley Z 2900 and will source one of your kits after we get home after our month long trip in August. You folks make it look so easy.

@richardroberts1090 10 месяцев назад

These video's and wiring kit packages are just plain Awsome Nat and his crew have taken so much guess work out of the processes and planning.

@mattcruz5915 10 месяцев назад

These videos are amazing and make me think I could DIY this (with no electrical experience). I'm going to let a professional do the first install, but I look forward to the day where I will DIY my next camper electrical.

@theghostlyorb 10 месяцев назад

You made this look so easy! DC-DC charging is on my list eventually and I can't believe how simple you made it out to be!

@EXPLORISTlife 10 месяцев назад

Thanks! Yeah, it's easy to overthink that charging leg of the system. Glad it helped! Thanks for watching!

@jasonb9913 11 месяцев назад

I used Anderson connectors on my truck for the DC-DC charger I have, its great. So great, that I cut the power cord to my Viair compressor and put an Anderson connector in the middle of that. Now I can power it from the rear bumper or connect the original clamps to battery up front.

@billharrington172 9 месяцев назад

Great Idea!

@donclark4063 2 месяца назад

What a great resource. You guys are so clear and concise with your tutorials. Excellent videos. Bravo!

@johnplyler7054 10 месяцев назад

The biggest problem for me is not the install, but the firmware updates. I don't design websites, but I think some major improvements could be made. I remember one site where you had to read down to the very bottom of the page and then click on this one word that was not even marked as access to the update! Thanks for another nice Sunday morning video!

@jjsantos3292 11 месяцев назад

Great work! Absolutely love the way these videos are put together, thank you!

@EXPLORISTlife 11 месяцев назад

Thank you very much!

@JesseHires 11 месяцев назад

I have an RV trailer that is nearly identical to the one in your video. Thanks for this.

@EXPLORISTlife 11 месяцев назад

Our pleasure! Thanks for watching!

@bobwojcik6196 11 месяцев назад

A great video. Your explanation really helps me better understand the whole process. Currently have a Sprinter Van I purchased used that has a rather sketchy system and know it’s going to need updating.

@EXPLORISTlife 11 месяцев назад

Awesome! Glad it helped. Thanks for watching!

@billharrington172 5 месяцев назад

BTW, I purchased the wiring diagram for this install an it has been super helpful. Well done!

@sethandersson7021 10 месяцев назад

I really could've used this a year and a half ago! 😂 Thanks for all the great advice!

@EXPLORISTlife 10 месяцев назад

Awesome! Glad it helped. Thanks for watching!

@John-eq8cu 11 месяцев назад

A pretty good installation. I did a similar one in my camper, but i used the 2kW Aims inverter/charger. With that system, the AC electrical is limited to 2kW, so I had to wire the inverter loads on a sub-panel, and wire the high-power circuits (AC and HotWater) directly to shore power. But the nice thing about the Victron Multiplus is that you don't need to do that, as the "hybrid inverter" will take extra power and 'mix' it with the battery power, all the way up to 30 amps. If I were to do it again, i'd use the Victron.

@mausie1967 11 месяцев назад

Love your videos. Not just this one but all of them

@EXPLORISTlife 11 месяцев назад

Hey, @mausie1967! I appreciate that. Thanks for watching! 🙂😀

@timf6916 11 месяцев назад

Good job. You guys are doing a fantastic work.

@EXPLORISTlife 11 месяцев назад

Thank you so much 😀

@craigquann 11 месяцев назад

That's an awesome setup.

@guttermastersplus5613 11 месяцев назад

Finally someone that explains the thing the right way and the simple way highly intelligent good video

@EXPLORISTlife 10 месяцев назад

Hey @guttermastersplus5613, Thanks so much! Cheers!

@Justthe2ofUs843 9 месяцев назад

As an installer, I approve this video. Well done. 👍👍

@EXPLORISTlife 9 месяцев назад

Awesome! Glad it helped. Thanks for watching!

@cristianperalta74 11 месяцев назад

Mennn, your videos are always very helpful Thanks...👍👍👍

@EXPLORISTlife 11 месяцев назад

Glad it was helpful! Thanks for watching :)

@RD27600 11 месяцев назад

Fantastic video!!! Shows me that I can do this. For a follow on video I'd love to see the addition of a generator and transfer switch like you'd have in a Class A.

@dtburrows 6 месяцев назад

Most helpful video I've seen. Thank you

@EXPLORISTlife 6 месяцев назад

Glad it was helpful!

@the_searchers 10 месяцев назад

Thanks guys. I really like the way you break it down

@EXPLORISTlife 10 месяцев назад

Hey @the_searchers, Thanks so much! Cheers!

@glenludwig5135 4 месяца назад

My God. Best video ever on changing to Solar. I wish you would do that same setup to a 48 volt system. Thanks

@EXPLORISTlife 4 месяца назад

Glad it was helpful! A 48V system would not be beneficial in this setup. It's too small.

@12v_obsession92 11 месяцев назад

Hey Nate, good install. A few things to consider here: The anderson connector on the truck could have benefited from a springback protected cover with grommets like the one supplied from trailer vision, likewise the anderson on the RV should have a cable sheath and rubber cover. The terminals will corrode and fill with water/dust in no time. For monitoring the the Cerbo GX would have been a great compliment to the system. Hope it doesn't get too warm down there under load. Anyway keep up the good work mate👍

@tonyrardon3227 11 месяцев назад

I used the Trailer Vision to cover up my SB50 connector on the truck and wrapped all wires in a cable sheathing to give it a nice clean look and protect the wires.

@bobfarrell6510 11 месяцев назад

Awesome installation

@EXPLORISTlife 11 месяцев назад

Thanks! 🙂🙌

@Mark_Lawler 11 месяцев назад

Another great how-to video!!! Thanks!

@EXPLORISTlife 11 месяцев назад

Glad you enjoyed it! Cheers!

@daviscrt 11 месяцев назад

Great information. Thanks Don

@camperbum 9 месяцев назад

Very good and cool how you showed what it takes to have a good system. Thanks.

@EXPLORISTlife 9 месяцев назад

Thanks so much for watching! Cheers!

@TumbleweedRvLife 10 месяцев назад

Another great video - Thank you! 💜💚❤👍

@anthonyrettig8617 5 месяцев назад

Great video!

@carykern6079 11 месяцев назад

Thank you for awesome videos and explanations. FYI, using Tabasco Sause, or Taco Bell "Fire Sause" works excellent at cleaning electrical cord prongs, old military trick that works awesome on copper or brass due to low pH.

@kroy106 5 месяцев назад

I'm more confused now than ever...... Not your fault, just more to it than I imagined, but I will do it myself 😉

@KJC63 11 месяцев назад

So helpful... excellent video.!

@EXPLORISTlife 11 месяцев назад

So glad it was helpful! Thanks for watching!

@cpwatching5647 9 месяцев назад

Excellent video. Thank you.

@EXPLORISTlife 9 месяцев назад

Hey @cpwatching5647, Thanks so much! Cheers!

@user-ic5yo6nl4w 3 месяца назад

Great video

@nekrojester6168 5 месяцев назад

Very helpful. Thanks for all these videos yas do guys. ;)

@canada59worldwide31 11 месяцев назад

Great videos

@sunbtanman7354 5 месяцев назад

You guys are great awesome video. Now I have to dissect what I need out of it. LOL

@RVingwithG 9 месяцев назад

😮😊just another GREAT VIDEO by Nate @ExploristLife Thanks buddy 😊

@EXPLORISTlife 9 месяцев назад

Hey, @RVingwithG! I appreciate that. Thanks for watching! 🙂😀

@KampingKids 11 месяцев назад

That is awesome! I’ll be doing something similar for my rig.

@EXPLORISTlife 11 месяцев назад

Awesome! Glad it helped. Thanks for watching!

@bobgordon5447 6 месяцев назад

Enjoyed your videos

@EXPLORISTlife 6 месяцев назад

Glad you like them!

@lickalittle 11 месяцев назад

I saw the GD and thought yes finely something I could use, as I have a 2500RL center bathroom, it's 29ft and have been pounding my brain how 🤔 I don't want to break the Artic Seal underneath and that one doesn't have the Artic package. Alas I'll figure it out, nice work as always and this gave me a couple helpful ideas 💡 Thanks again for your time...

@billharrington172 9 месяцев назад

my GD 22MLE (like in this video) has the Artic Package... it's a 2021

@michaelparks3106 10 месяцев назад

I have pretty much the same system on my Grand Design 2670MK, but since I have a 50amp system I went with the MultiPlus II. I did the wiring is a way that I think was a little easier, required less cable so it was less expensive, and has fewer connectors so there are less points of failure. For the shore power, instead of running a cable from the stock shore power line at the fuse box to the MultiPlus, I just disconnected the shore power wire from the fuse box, unscrewed the socket from the outside wall and pulled the whole thing out. I then drilled a hole (I think it was 2") and screwed the connector to the wall next to the storage compartment where the MultiPlus was, the stock wire was more than long enough to reach it directly. So I only needed one Romex 6/4 cable to go back to the fuse box for the 110v line, not two. For the 12v coach battery same idea, instead of running "battery relocation" wires from the new battery to the old battery location, i just rerouted the stock factory wires direct to the new battery. Once you drop the belly pan, pulling the wires from the old location to the new is very simple, and since the battery in the storage compartment is closer to the fuse box than the old one was, the wires are more than long enough. I've always felt that the less wires and connectors needed to get the job done, the better. Other than that, great video.

@EXPLORISTlife 10 месяцев назад

Neato! There are 100 different ways to do this stuff and I'm glad you found a way that works for your specific application. What you described won't work for most people as the wire lengths are often not long enough to accomplish that, and if somebody has Jack's, slides, or generators, running the factory 12v wiring to the lynx distributor will not deliver enough power to run as that factory wiring is only big enough to run the converter and not necessarily those larger oem items. But yeah, glad you found what works for your specific application. They way I showed will work for 99% of applications, which is more what I'm interested it. But other than that, good comment.

@OnyxRayven1 3 месяца назад

Thanks!

@berthaduniverse 11 месяцев назад

Nate, great work. One kinda significant point, the solar panel roof anchors were not installed properly. Ideally the surface between the roof and bracket should have been pre-caulked and then anchored (using something like Sikaflex or Lexel), then lap-sealed around all 4 sides and holes. The way it was done here, capillary action will draw water under the back of the plate on the one uncaulked side, and allow a leak or backerboard to rot.

@EXPLORISTlife 11 месяцев назад

Thanks for watching! The tape we used is specifically designed to form a waterproof gasket. I know this may not be enough for everybody (much like everthing I show on this channel 🤣), and if that's you, feel free to dicor/seal where/however you like.

@berthaduniverse 11 месяцев назад

@@EXPLORISTlife sorry, didn't see the tape, must have missed it. I agree, a Bituthene like product can work well in a "smoothish" surface.

@chachi5975 11 месяцев назад

For those that don't have a solid roof on their travel trailer, using channel strut into the crossbars of the roof make a secure mounting bracket for solar panels. If your travel trailer is an ultra lite and didn't come with a ladder attached, it's probably too thin to simply screw into and hold the panels.

@camustang1966 10 месяцев назад

Have you looked at the new flexible solar panels from Bouge RV (CIGS)? Are they practical for RV roof installation and usage? This was a great video. Probably the most comprehensive, yet snappy videos explaining this whole process. Well done. I have a fifth wheel, but I could adapt this to my situation very easily. Thank you!

@loucinci3922 11 месяцев назад

Well done

@EXPLORISTlife 11 месяцев назад

Thanks! 🙂🙌

@EBKRV412 11 месяцев назад

Another awesome detailed video guys! What a great install this is I'm sure the owners are very happy. Do you happen to have a link to the blind bolt kit you used to attached the ground from the lynx dist to the frame?

@darrylm3627 3 месяца назад

😄👍Good Stuff, Great Tips

@EXPLORISTlife 2 месяца назад

Thanks for watching! Cheers!

@pocketchange1951 11 месяцев назад

👍👌❤️🇨🇦, thanks for all of the info, much appreciated

@EXPLORISTlife 11 месяцев назад

Thank you so much for watching! Cheers!

@awall_wants2no 11 месяцев назад

Love your videos. Been waiting for this one. How come you grounded the solar charge controller to the inverter/charger? as oppose to doubling up on the ground stud on the lynx distributor? Can you do this with any inverter? I have used your videos to upgrade my rv's lead acid batteries with 2 100 amp hour battleborn batteries, the lynx distributor, and I am currently adding the victron MPPT Charger controller. I did find your videos after i upgrade my oem WFCO converter/charger for one that has a lithium battery switch and I am keeping my existing Xantrax 2000 Inverter. I am not sure if i can/should ground the solar charge controller to my Xantrax 2000 Inverter or what the alternative would be. Thanks for all these videos! i just let them play all day while I am at work!

@hexd2g 11 месяцев назад

Great video! Can't wait to follow your guide for my Grand Design Imagine. Did you reinforce the wall to install all the Victron components? Would the Victron Multiplus 3000 be enough to power the AC and would it have any heat issues in the storage bay? Thank you!

@heashepard23 8 месяцев назад

I have a 2019 sprinter 170 extended with 60K miles and many options including 10 inch display and cameras all around. Following your instructions, I added a 500 watt inverter (only about a 30amp draw) to position 6 in the tray using 2awg wire. Connecting to the X145 term #1 I ran a wire to a 200 amp isolator so that the inverter could only operate when the engine was running. This was for emergency purposes if my rerar 3500 watt inverter connected to 800ah lithium battery bank ever crapped out. After putting everything back the engine started right away. took it for a test drive and everything seemed to work as intended, BUT after driving 70 miles to camp on a friends mountain property ---the chassis battery was below 12 volts and it would not start I fact the entire MB side of the house was blacked out--NO LIGHTS ete Borrowing a charger and a long extension cord I was able to get the battery to 12.9 volts and restarted the van in the morning. It immediately went into fast idle mode (an option I did not select when I purchased the van) and this lasted about 10 minutes before slowing to 800 rpms. Driving it out of the mountains, there was a check engine light and glow plug light as well as a battery warning message --also none of the lane keeping or adaptive speed control would work. After replacing the battery and charging it overnight, all functions returned. It has been to the dealer twice. At their suggestion, I disconnected the inverter from the tray. BUT it still does not appear that the alternator is charging the battery.. I returned from a 4500 mile trip camping around the Great Lakes last month. The van ran like a champ averaging 20mpg and never having an issue starting. Do you have any idea what could have gone so wrong? The dealer's head Sprinter Tech said since 2019 the alternator and entire electrical system is mighty touchy. He suggested if I would like to again connect into the OEM electrical system to do so at the battery.

@paimormusicstudio6423 11 месяцев назад

Great video, i always enjoy your detailed explanations. What am i missing because I am currently using an all in one EG4 3kw invertor, with a EG4 48v battery. Then all i had to do was run the AC output from the EG4 invertor to the RV shore input..done, very simple installation. The solar panels just plug into the EG4 and charge the EG4 battery, and i can charge the house batteries as well. I use my house rv batteries for emergencies. And the EG4 also has an AC input for a generator to charge the batteries quickly. however i am in a permanent location so perhaps that is different.

@EXPLORISTlife 11 месяцев назад

Awesome! Glad it helped. Thanks for watching!

@rudivandoornegat2371 11 месяцев назад

This will be another classic video of the Explorist life channel. In the video on Victron Energy RU-vid channel titled Victron VW Van Electrics Install - Episode 3 Mains Electricity at 4:45 min they put a 3D printed protection cap for the Lynx system. Maybe EL could sell these too in the future for people that are interested?

@EXPLORISTlife 11 месяцев назад

Ah, nice! Good idea!

@mikemcguire5859 11 месяцев назад

Nate. Great DIY/PRO videos. My question is, why not use the tined lugs vice regular copper lugs and get away from any corrosion on lugs and bare copper bus bars. Thanks for sharing all your great content.

@EXPLORISTlife 11 месяцев назад

All of the wire in the camper is un-tinned copper. I suspect that the ceiling and floor will rot away before our un-tinned wires need to be replaced due to corrosion. Tinned lugs are really only needed in marine/salty envrionments.

@680AaBb 11 месяцев назад

Thanks @EXPLORISTlife for this great video! You've inspired me to tackle my tow behind travel trailer with 30A shore power. I hired what I thought and what many other people in my area thought was a good installer. He installed 2 ea 200watt solar panels, and a victron multiplus compact, 12v/ 2000va/80amp inverter charger and a ruching dollar mppt charge controller onto my trailer. I have 2 100ah lithium 12v batteries, but the about every 3 months the batteries are destroyed and I have to use the warranty to get new ones. I suspect the installer lacked the training to program the inverter or the charge controller correctly. After seeing your videos I'm going to attempt to correct this issue. Quick question, can I fully program the victron with the ve.bus bluetooth or do I need the mk3?

@sylvainbeaumont7703 9 месяцев назад

Bravo !!! Great video

@EXPLORISTlife 9 месяцев назад

Thank you very much!

@sylvainbeaumont7703 8 месяцев назад

@@EXPLORISTlife I'd like to ask you a question about connecting the inverter directly into the breaker box of my RV

@EXPLORISTlife 8 месяцев назад

You should do that then. 🤷😂

@sylvainbeaumont7703 8 месяцев назад

@@EXPLORISTlife OK ! 🙂 If i turnoff the converter breaker in my Rv, the lights an the fan of furnase will continue ti work ? (excuse my english, i comme from Québec and i speak french! sory

@EXPLORISTlife 8 месяцев назад

If you follow the instructions in this video, all of your pre-existing components will still work as designed.

@toniawilkins-schafer8130 9 месяцев назад

Love your videos. Would you have an update as to how the Multiplus performed mounted on its side? I would like to get the Mutiplus 2x 120 but I have an older model RV and the height in my bays are under 23 inch in height. I thought of doing a side mount.

@azvanman3636 11 месяцев назад

Great video, I have been waiting for this since you announced a travel trailer upgrade video! In our old travel trailer we followed your diagram and installed the older Victron MultiPlus Compact 12/2000/80, that we will be reinstalling in our new trailer. When the power assist function of the inverter is on, will the 10 gauge wire be sufficient to handle the extra amperage or, will I have to use as previously recommended, the 6 gauge wire? Thanks for all you do!!

@FarmerCal 7 месяцев назад

Great video. If the RV had an onboard generator, how would you accommodate that with the equipment you have used in the video?

@dancanrv2 9 месяцев назад

GREAT job/video ... mentioning the approximate price of components and cables/parts could be very useful !!! cheers

@EXPLORISTlife 9 месяцев назад

Better than that, I shared where to find the EXACT price in the pinned comment.

@andrewk1916 Месяц назад

@Explorist Life Team - Awesome video for us TT DIYers! Thank you for creating these videos and offering the equipment and kits via your store. As many others have previusly said, your work and videos coupled with your store makes sourcing and installing for us DIYers easy, safe and uncomplicated! You pointed out on this install that this particular system was too undersized (meaning battery bank) to power the AC compressor. But could a samll 300amp hour(ish) system power a 15K AC compressor if the AC has a soft-start OR a 13.5K AC with a soft start? My assumption is "Yes" but I'm hoping you can give a quick clarification. Thank you again for the great work!

@billharrington172 5 месяцев назад

Hi Nate, great info and so well presented - as always! One question, you've mentioned stress testing your installations but I've looked around and can't find any information on how you do that. Any suggestions?

@jonrockefeller6068 11 месяцев назад

What are those video lights you are using for task lights? They look nice, compact and easy to use. Thanks for sharing! Hope you are enjoying those new headlamps.

@DenoGodin-lt6qq 10 месяцев назад

Excellent video Nate. In a tight pass thru situation like this is it possible to mount and pre wire connections as much as possible and then slide the “equipment board” into the pass thru? Being over 225 lbs I doubt I could fit to mount and wire the equipment. Any draw backs?

@april7_ 11 месяцев назад

I know this may be against recommendations but 10 years ago I only glued solar panel mountings (no penetrating screws) with Sikaflex®-521 UV and when 2 years ago upgraded bigger panels, I was not able to tear those mounts off the roof! So I think If you want to avoid holes in your roof, that is a safe option. Got also my seeking satellite dish 40x40 cm plate only glued to the roof over 10 years and it is tight there still!

@shadowfire77 Месяц назад

Great video as usual. Still curious about the heat anticipation and how the stress test went out with the multiplus mounted horizontally.

@EXPLORISTlife Месяц назад

We had no overheating alarms during our testing.

@beaugagne1 11 месяцев назад

Great video. I'm curious why you didn't choose to use the 2x120 Multiplus II to separate the air conditioner circuit to operate from shore power only? Would have required some additional wiring, certainly, but would have ensured the owner did not have to 'remember' to not use the A/C when operating only off of battery power. Perhaps using just the a/c fan without cooling was a requirement? Or perhaps it was a budgetary decision not to opt for a 3kva inverter. Either way, great installation!

@rocket1point0 11 месяцев назад

I've always enjoyed your videos and so happy to see you've expanded to more videos related to trailer conversions vice building a system from scratch. This is outstanding! I had some concerns / questions on this one: 1. What is driving such large awg cables for chassis grounding (e.g. 2/0 and 2 awg)? With the exception of marine applications, I thought 8 awg was called for at a minimum (unless, of course, you are using the chassis as the negative side of power distribution). 2. I would caution using the trailer's aluminum wall and compartment framing as a chassis ground source. There could be instances when these are not grounded to the chassis frame. I would recommend running this under the trailer to the main trailer frame. 3. How was the emergency brake disconnect accounted for? In the completed configuration, it appears that power to the emergency disconnect would not be present if the main battery disconnect was turned to the off position. Normally, the emergency brake disconnect switch is wired directly to the positive terminal of the battery (or in my trailer's case, to the unswitched side of the battery disconnect). Also, this is usually an unfused connection. Thanks again for such a great and informative video!

@EXPLORISTlife 11 месяцев назад

1: ABYC states that the chassis ground shall be no smaller than 1 size smaller than the largest wire in the system. 2: Choose the most available and solidly attached piece of metal available to you in your installation so that the most metal on the van is connected to the battery negative. More often than not; the camper frame is electrically and physically connected to the trailer frame. 3: The electrical system 'new' main disconnect switch should remain on any time the camper is not in storage or under maintenance so that all of the factory systems work properly.

@rjenkins133 10 месяцев назад

I am a bit nervous with putting the emergency brakes on the other side of the main disconnect switch. If you forget to turn on the main switch you will be travelling without emergency brakes. I would probably put the brakes on an unswitched branch of the battery bus. I am also a bit nervous about not using a fuse on the emergency brakes. A shorted wire on a large battery - whether lead acid or lithium can cause a fire. When everything is mounted on the metal frame of the trailer - the fire is probably less likely - but if the battery is inside and the wiring is bundled with other wires and through walls, etc. then I think a fire is more likely. I would fuse the the unswitched branch with fuse sized to operate the emergency brakes.

@EXPLORISTlife 10 месяцев назад

@rjenkins133 That's fine, and you can do what you want, but the master disconnect is for storage only. There are certain things you need to 'remember' when towing a camper. If you 'forget' to plug in your 7 pin connector, you will also be without trailer brakes.

@bug512 6 месяцев назад

Thank you, your builds and videos are top notch. My question is why are the battery disconnects on the positive side? On Battle Born’s website it says “A battery disconnect switch can be installed on the negative or positive leads of a battery and it will effectively disconnect the whole circuit. However, installing the switch on the negative lead adds additional safety.” In years past when I worked on cars, RV’s and such the disconnect was always on the negative. Maybe you can comment.

@EXPLORISTlife 6 месяцев назад

I've actually never seen a switch on the negative side in-person on an actual build. I prefer the switch being on the positive side because it will always cut off power without question. A switch on the negative leaves the positive wire powered which in my mind seems dangerous; but I also know it is another fairly widely common approach.

@MrDukaman 10 месяцев назад

Great video. Good detail. I'm a master electrician. And I really don't know much about solar. Is it possible to incorporate a small wind turbine for some charging voltage during night time. Just a thought I'm having. I'm learning about installing my own solar system. Also I'm a solo camper. And I love the national parks and boondocks g off grid. Thx for sharing. Nice work🇺🇸👍

@EXPLORISTlife 10 месяцев назад

Good question! It's not really feasible to add wind charging for a remote application. Wind turbines need to be pretty big and tall to have much measurable effect, and storing that stuff during transit isn't something most people want to do.

@DCanavan-Imagine2600RB 3 месяца назад

Fantastic video broken down into easily explained and understood segments! When you discussed mounting the Multiplus horizontally, you mentioned stress testing they system when you finished the install. What were the results of the stress test and any heat issues with the Multiplus? As with the Imagine you worked on, I have the same issue with the lack of vertical height sufficient to install the Multiplus vertically. Also, did you make any note or measurements regarding the fan volume of the Multiplus while in use? Would it be feasible from a noise and heat standpoint to install the whole set up on the opposite side of the bulkhead underneath the bed?

@wardg.5559 3 месяца назад

What an awesome video. I'm just lost with my inverter/charger on my camper.. it's plugged into an outlet? I'm assuming to power to 110v outlets?

@tonyabdalla 11 месяцев назад

Love your videos Nate and Team EXPLORISTlife! I've noticed you prefer all copper lugs over tinned copper lugs. When it comes to long-term corrosion protection, do you see any added benefit to tinned copper lugs? Thanks and keep the great vids coming!!

@EXPLORISTlife 11 месяцев назад

So, all of the wiring in a camper is un-tinned copper, so to me, the added expense of making the wiring last longer than the factory wiring is not necessary. I'd suspect the frame and roof of the camper will rot long before the wires corrode to the point of needing replacement.

@tonyabdalla 11 месяцев назад

@@EXPLORISTlife Makes sense. Thanks for the reply!

@Sylvan_dB 11 месяцев назад

Tinned copper is important for marine or similar harsh environments, not nearly as important for this application. In the old days with lead-acid batteries the terminals attached to those batteries needed to be tinned because acid. LiFePO4 don't have that problem. (thank goodness!)

@aliasimondi5054 11 месяцев назад

Wow! What a great video but the info is a little over my head. I’m new to RV’ing. I just bought a small Coleman (Dutchmen) travel trailer. I’m hoping to start with a small project as follows: I’d like to upgrade to a Battle Born house battery and add a Victron Orion 12-12/30 DC2DC charger with Anderson connectors for alternator charging as I drive, as you did here. Here’s my question…will adding the Orion cause complications with the existing OEM charging equipment? i.e. Can I add the Orion without removing and/or replacing the OEM AC/DC charger?

@maxxonetwo3 11 месяцев назад

Can I bring my camper to you ? Depending on how far you are. You can install this system for me. Thank you again for a great clear speaking video. Lake George,NY

@EXPLORISTlife 11 месяцев назад

We have installers you can take your camper to: explorist.life/find-a-certified-installer/

@ravenfan1016 5 месяцев назад

Really nice job with the explanation of the whole process. One question you mentioned that the Victron inverter is not sized to handle the A/C. Would installing a Micro-Air easystart on the compressor work for a setup like this?

@meececa 11 месяцев назад

Thanks, I subbed after watching 😊. This is the first video I’ve seen that you’ve made. Would this set up also accommodate a small generator?

@meececa 11 месяцев назад

Hmm, just realized, yes it would because the generator would connect to the shore power.

@EXPLORISTlife 11 месяцев назад

Exactly!

@OffroadVikingr 10 месяцев назад

Very informative video. I am planning to add solar to my 2022 Grand Designs Imagine 2600RB. We want the system to support running the A/C as well. What capacity battery bank and solar array should I be looking at? Thanks.

@Sylvan_dB 11 месяцев назад

I like to connect to distribution panel(s) instead of the original A.C. and D.C. supply locations. Sometimes this is excessively difficult for one or the other, but not usually both A.C. and D.C.. Did you evaluate connection to distribution panel(s) or just decide to simplify to this universal approach?

@robertkelleher1850 4 месяца назад

This is amazing. I've watched so many videos on Victron's own channel and come away more confused every time. Question: If the negative side of the Lynx is grounded, then why is the additional ground wire from solar to multi required?

@erickessler6094 6 месяцев назад

Nate & Steph, It was so nice to see the beautiful job you did on Kurt & Laurie's 22MLE! OMG, I say, because my wife & I, also retired (and my college buddy Murf & Nancy) have 22MLE's as well! 😎 Mine 2023 came with a charge controller & Solar on roof, but we want "MORE POWER" lol. Maybe 3 or 4 panels? All I have done so far is upgraded to a 12v 230Ah LiTime battery. 1. I've watched your 12v vs 24v discussion and wondered if building the same system you did for Kurt & Laurie... but with a 24V Battery & System would have good advantages? 2. Also I love that Victron Power Assist feature, but could I use that with my lil 1600w (2000w surge) inverter generator to create enough power to run Air Conditioning? 3. Where are you & your shop located? Cheers, Eric

@EXPLORISTlife 6 месяцев назад

Thanks! 1: There is no reason to do this system as 24V. 2: Probably. Especially if you've got a soft-start on the AC. If you want a guarentee that the AC will work; you'll want the next size up on the Multiplus (3k) w/ a little bigger battery bank (400Ah minimum). 3: Northwest Colorado. We ship worldwide, though, and ship for free on orders over $200 within the contiguous USA.

@erickessler6094 6 месяцев назад

@EXPLORISTlife Thank you for your reply. If I understand correctly, the combo of my battery bank (with a 2nd 230Ah battery) and my 1600W Generator (and magic of the Victron "Power Assist") WILL power my Soft Start AC. But best if the Inverter-Charger were 3000 vice 2000. With 3000W capability, am I at risk of the stock Battery wires overheating? I noticed your battery relocation kit used much heavier wire to the stock batery box location. Cheers, Eric

@tompaoletti690 7 месяцев назад

Great video incredible detail!! but you eliminated a significant amount of storage 🤷🏻based on your trailer style/brand. Is there a smaller controller(s) that would work?

@erickessler6094 6 месяцев назад

Nate & Steph, Wow, this is my 3rd time watching this video! Ha-ha 🤪 I see you used a Victron MPPT 150|60 Tr charge controller (not sure what the Tr means?). I'm sure all solar panels are different, but my Furrion panel is 165W with that Voc spec at 20.4 (so if my goal were 4 panels, then ... "I think, if I'm beginning to learn," all I need is 4 × 20.4Voc = 81.6 . Like a Victon 100|30 or 100|50 ??? Does this mean your friends 22MLE have panels with high power Voc specs that drove the 150|60 Tr Charge Controller? 🤔 Cheers & thank you, Eric

@SaltyDog711 3 месяца назад

Great video! by chance do you have a video that has a solar panel already installed on the roof by the manufacturer? I have a 24' Winnebago Micro Mini with a single solar panel on the roof and says it's prewired for an inverter but I'm not sure where to start and what I would need for a system like this. Thanks!