Samsung Washer Repair 

Excellent video, right to the point and no unnecessary commentary. You saved me a ton of money, thank you!

I watched your video twice and then dove in. Took all day but my wife thinks I’m a superman and my buddy’s think I’m a god. Thanks SO much for posting this video. If you are ever up here in Canada and near Hamilton, Ontario I owe you some beer. And up here in Canada we put alcohol in ours. Cheers! Derek

Excellent video! I needed to replace the front gasket on my Samsung and I felt like a genius! Little did I know I had much to learn 🤦🏾‍♂️🤦🏾‍♂️🤦🏾‍♂️. My bearing has gone out as well. Time for an LG direct drive washer!

Well done JB,I normally get really bored watching these types of videos, but I watched the whole thing no fforwards. I can't seem to get the drive belt to stay on my machine. So hats off to your patience and skills👌 👏 🙌

A superb, no bullshit video!

Nice job JS, thank you for sharing this, I might just tackle mine now you've shown me how it's done. Thank you once again.

Thanks man! I had a heck of a time pulling my inner bearing; but, I rigged up a puller and put some pressure in the right direction so that I could knock it out in a couple blows with my small sledge. I’ll have my replacement parts in a few days; looking forward to getting this machine back up and running!

Repaired mine today, $40 on Amazon, about 3 hours and 2 cuts but got 'er done.

Great video! Thank you for also recording how to put it back together after replacing the parts. Very helpful

Thanks for the video, it really helped. I was working on a Samsung built Kenmore which had some minor variation. EBay was were I found the parts ($80 for a bearing and seal kit). I would add that wearing gloves is critical as the inside of this machine is razor sharp. Marking all fasteners with their origin and taking pictures throughout the disassembly makes the reassembly go more smoothly.

He is strong, fast. The woman's dream.

Outstanding video

You’re not supposed To knock those bearings in the tub with a hammer metal to metal you could damage the bearings not very smart you should use a piece of wood to knock them in

I know this video has been out for a while. I hope someone can help us. We have this same washer and having a hard time finding the spider arm for this unit. If someone could point us in the right direction on finding the correct parts number or compatible number, it would be greatly appreciated. Thanks

Appreciate the video. Thank you!

How do you break the seal on the bolt in the back? I'm getting no where with it

at 9:26, using the old bearing to knock the new one into place is a nice trick.

Great vid. What crap they now make. If they would keep speed slower on spin and let it run longer. Bearing and seals would last. Check old spin rates and the new sonic spin rates.

Wow this looks like a fun repair. I have the same machine and I'm having a rubber burning smell.

Cannot thank you enough for this video. Gave me the confidence to open up the washing machine. My drum was not rotating, totally stuck and I was pretty sure something was stuck in it. Called Tech who charged 170$ and told me that there was some problem with shaft and asked me to replace it, my unit is only 3-4 years old. On opening the drum, I found broken kids scissor which was getting stuck. Not sure how it ended up there. Few tips/suggestions, it is not this quick and takes lot of time, many hours, so be ready for it. You can take pics of every part you are opening so that you can put it together back again by looking at the pictures in reverse. The drum is heavy so you may need help. Also, I felt it would have been easier for me to put the bolts which tie the drum to hydraulic suspension on the back side if I had put the weights first on the front side. Without it the drum becomes lopsided towards the back and a major pain to put the bolt in. Make sure you fix back everything based upon pics, I had missed putting the screws for the sensor on top of the drum and due it the machine would not go into rinse cycle. Took me 2 hrs to figure that one out. Nothing beats the thrill of getting it done and saving tons of money, even if you do not fix it you have practiced enough for future issues ;). Hope this helps someone in future.

What a man!

You Sir; are my hero. This saved me likely hours if not days of confusion and frustration.

Masterclass! A scrud build up lead me here, but the entire strip down is really useful, thank you 🙏

How cane I open the door handle? No screw found

Truly fantastic video. It was extremely helpful. Thank you so much for sharing your expertise. 🙏👍

Great video, thank you.

Go watch another video on this same washer. You’ll be sorry if you stick with this one. All kinds of important steps left out!!!

I bought for $999 in 1999 a Maytag Neptune, the water pump went bad after 6 years, the ball bearings went bad after 10 years and the motor after 14 years. My $1,599 Samsung machine, (WF50K7500AV/A2), the ball bearings went bad after 3 years and even the water pump still good, normally that's the first thing that goes bad on any washer machine. With only 1 year warranty, customer service does not care. I will never buy Samsung again, those are just pretty garbage, they should keep making just cellphones. SAMSUNG NOT RECOMENDED. GE or Maytag again will be my next choice.

Hi, thank you for the video. I have a Samsung front load washer WF361BVBEWR/A2. 01. I changed the rubber seal a few weeks ago and since the the machine vibrates and moves to the left only when the spin cycle gets to the high speed, then its fine. It only moves probably 2 times per the wash cycle. Otherwise is doesnt move or shake the rest of the cycle. Any thoughts? I changed all 4 shock absorbors yesterday and still moves. Do you think it could be the bearing. Any feedback would be appreciated. Thank you

When I search for bearing 6307-2RZ nothing available only 6307-2RS will that bearing fit ?

My washer stopped spinning today. Motor works just fine, but the barrel doesn't move. While I'm fairly certain it's not the bearing that's the issue, this video is still going to be really helpful to me tomorrow when I start ti disassemble it to find the actual problem. Thanks!!!

Hey where did you buy the parts from?

18MINS??!!! WHAT WILL I DO UNTIL THEN???!!

Wow never use a hammer on the bearing and are we just going to ignore the slit on the bottom of the seal 😉

I know it's been 2 years since you made this video, however could you please tell me exactly where you bought the replacement bearings from???? Having a very hard time locating the right ones, there are alot of different ones evidently. Thanks!

I own the Samsung WF42H5600AW. It seems I now get to do this onerous chore. Bleh.

Is this a vrt? Do they have belts . Mines not spinning because a big blanket was put in and now it won't spin . Any one gone threw this? Please help

I just fixed mine to it was all day but works like new now the oil ring is dc62-00156a

That was easy 🙄

any idea i have replaced eprom board and machine powers on but nothing on display just flashing ? do i need to reset it or what it does not react to all i hear powering on sound and thats it after that just all light flashing but not reacting to anything else except power on and of

Where can I find the assy shaft(spider arm) and what's the part & for after market, since Samsung discontinued the part

but you forget the most important, grease the seal bearing

God bless your bro… you have some patience… I was thinking about changing mine, but just looking at this makes me nauseous… But good for you… 50 bucks.. well worth it if you’re that skilled

Great Video! I'll be doing this next weekend! thanks for sharing.

thanks for the video i will never buy a samsung now, how old is this model and how long have u had the machine ?

I got the same problem,when the spin cycle at 6 minute it make a big big noise and seems the whole machine moving.And i just got my new washer installed.Anyway thanks to post this video ,it gives me confidence to replace the bearing on my own.By any chance what year is your washer?

When You Open The Back Panel I see There is no Sound Dampers ?

Thank you! Very helpful

i think you forget 5:05 washer

You are washing machine super man.

Great video with no commentary. You help people save money. Thanks.

Man this video awesome no bla bla it was like watching a soldier put his gun together nice work

Bravo. Excellent job. Thanks for the video.

Thx for this very video. What's that ring or washer you put on before putting the seal in at 9:43

Thanks for your information 👍 very helpful

Where did you fing the bearings and seal?

Nice Job but what a PITA!

can u tell me what are those connections on the door gasket? and what is that sensor for on the gasket?

Why do repair guy want to replace the drum instead of just doing a bearing like this surgeon

That’s a beautiful machine

Thank you!

I'm working on one too thanks for the video

This is great, but I can't find those bearing part numbers anywhere on ebay! Could you please post a link to the seller?

Good job bro!

3

You made it look TOO Easy. @4:50

Junk should last longer very pricey

May I ask how old this machine is, was it used at all? It looks like new, even inside, how did you manage that? greetings

Great video thanks

You missed a few things that I'm finding the hard way now.

You need narration - uou told nothing

Be cheaper to just buy a new one

!!!IMPORTANT!!!! I have this almost exact model WF50k7500AV/A2, I couldn't figure out why it was grinding after I bought the back half of the plastic tub with the bearing's installed already and a new metal tub with the shaft, the whole thing was brand new from Samsung parts about 800$. if you get the back plastic part of the tub with bearing installed even though it's O.E.M, they must have redid it because my chrome spacer plate under the Stator rubbed bad, it made little grooves on the inside of the Stator cover Knew it had to of been the Spacer plate. I took out the adapter plate and it's like new..... thought it was the new bearing's at first figured it out, it was a pain so ya im pretty sure the tub with the bearings was redesigned to not need the adapter plate. anyways few days of headache's but figured it out just a heads up.... your video was excellent the only difference on your model compared to mine was my dispencer bolted in from the top not the front and I had 2 screws in the bottom underneath that held the front face on... thanks for the awesome video.

ouch that hurts

Lo

Anyone no the part numbers for seal and bearings and we’re can I get them thank you