SELF-EJECTING DRAWBAR - Optimum MB4

Подписаться 15 тыс.

Просмотров 21 тыс.

50% 1

! Morsetaper can be a pita to remove from the spindle, so i came up with this simple drawbar, which automatically ejects the tool, and you don't need to whack it with a hammer like crazy.
00:00 - The problem
00:12 - the washer
00:38 - the solution in theory
01:20 - washer machining
01:57 - the drawbar
03:19 - the hex head nut
03:56 - the oopsie...
05:48 - installment
the fusion drawing: www.dropbox.com/s/tty1sva1a0g...
if you want to support the channel: ko-fi.com/christophlehner
Thank you very much !! if you want to support the channel, you can buy me a coffe:
ko-fi.com/christophlehner
Thank you very much !!!
*affiliate links:
my camera: amzn.to/3Ef7ObP
my lens: amzn.to/3fG1sYY
my mic: amzn.to/3rtPSTi
or you can also support me through paypal:
Paypal Me: paypal.me/clehn8ok

Наука

Опубликовано:

16 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@markjmaxwell9819 Год назад

Loved the old Bridgeport milling machines they were well built and well designed.

@RustyInventions-wz6ir Месяц назад

Very nice work. Clever idea

@stylianos4570 Год назад

Thank you for your video! I made the same modification inspired by you! Thanks again for the idea!

@arjundas708 Год назад

Excellent sir am facing the same problem, nice solution to make, thanks a lot

@ProfSimonHolland Год назад

excellent work....great idea

@seanwolfe9321 Год назад

Very Nice! I have been considering how to do this with my Precision Matthews pm727m, this looks to be very similar. I can see where the length below in taper area is crucial, thanks for the heads up!

@billfisher7644 Год назад

I am keen to make the same modification to my Cormak ZX7045 and tried to link to the fusion drawing without success. Is there any other way I can gain access to it? Looks like a great mod though.

@anmafab 2 года назад

Nice video Christoph. I haven't seen this done before although saying that most of the RU-vidrs i watch have the r8 system. Any reason why this might not be a good idea? Looking forward to the gear hobbing vid ;)

@ChristophLehner 2 года назад

Thanks for the comment andreas! Since R8 should release the tool, nobody really needs it. Some older german mills with morsetaper spindle had this kind of drawbar straight from the factory. I am afraid, the gear video will take a while, since i want to build a diesel furnace first :)

@anmafab 2 года назад

@@ChristophLehner good info. Doesn't look like a super complex mod. Is this a prerequisite to a power drawbar for an mt spindle? A diesel furnace sounds like a big project!

@ChristophLehner 2 года назад

You got me. The butterfly impact wrench is already on its way :) Yeah it's also quite expensive, but i want to get into castiron

@HM-Projects Год назад

@@ChristophLehner The Chinese Sieg mills have this feature as well but even with that I have to be careful to not over tighten or the MT3 taper tooling is a bit hard to dislodge.

@hansreker675 11 месяцев назад

I made the drawbar , but not all the collets I have are even in length (diameter) so I need to grind them even because they don’t tighten up. this system is 6:51 the only way not to load the bearings

@incubatork Год назад

I have an HBM BF28 milling machine, the tool eject system it uses for the MT3 collets is almost the same but is to my mind very weak. The nut is a small 3/8 size square milled in the shaft made so it can pass through the eject collar from the top and unscrewing them both from the mill. I was looking for a way to beef things up a bit, more for peace of mind than anything else. I use an air powered butterfly wrench to tighten and loosen but at times I need to qive it a knock with a hammer or increase the air pressure to the butterfly wrench to get It to eject. I like your idea but will make a complete new drawbar, slightly longer, its a shame your video goes too fast to follow, though good and have watched it 3 times already to try to pick up finer details etc. thanks for planting the seed for the idea, now lets see how it grows. Does the Hydrocloric acid permanently blacken the steel? Here a small bottle of steel blueing liquid is expensive, 250ml over 20€. the acid is much cheaper if it works.

@ChristophLehner Год назад

No, the acis will slowly eat away the steel, i used it only to get rid of the zinc coating

@vivigarr Год назад

I am heavily considering getting one of these mills. How has working with it been like?

@ChristophLehner Год назад

For what it's worth it's amazing, but plan some budget for a DRO, without it's only half the fun.

@nitropiet Год назад

@@ChristophLehner Check out TouchDRO, it works really well. Thanks for this amazing idea, I am waiting for my 30 taper spindle to address the same issue :)

@vivigarr 3 месяца назад

@@ChristophLehner1 Year later I ended up going with the OEM company that makes the PM-30MV. Mill is great so far even though I haven't gotten it set up. Quality inspections seem like it's a really solid machine and all the machined surfaces are better than I expected! I was disappointed to find the ISO30 taper I thought I was getting is actually an NMTB30 taper so instead of pull studs it's threaded. However I have some threaded holes on the spindle face that are M10 and I think I can sacrifice a few millimeters to make an NMTB30 "shim" seat to BT30 tools. It'll be an interesting project some day. The main reason being I want to share tools between CNC router and manual mill. But it's not that big of a deal right now.