Lost my CD manual and couldn't figure out how to get self level on for nothing and I watched your video and did it ion two seconds. Thank you and I did subscribe.
Thank you very much. I can't get my switches to work for turning on self level, so I'm going to try "stick" leveling instead. Your video was a big help!
Thank you for pointing this out and was getting very frustrated with it and couldn't find it anywhere. Turned it on and now can't wait to slap a camera on it.
Thank you very much. This was a small but important bit of info I needed. I have found a number of your video's very informative. Thanks for taking the time to share .
plz help me two out of 4 motors are spinning very late in my quad i am using Kk v 2.1.5 everything seems fine but my motors are not spinning at same time i have set minimum throttle to 20 Any help plz ?
Happy to help but please watch ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-olIqTiSJHIY.html and come back to me with more detail of what you've tried..
Please see my quadcopter building for beginners series where I cover all of the steps and components that I commonly used to build quadcopters. Hope they help!
good video thanks. can you please also advice here. i am new to quadcopter and i had 2 mojor crashes after which i had to replace parts and it seems that crashes are related to Self level because i crashed after Turned On Self level. (it was default settings i think). and what is even more frustrating is i was just hovering not even flying at the time of crash. i fly more or less stable now and usually turn the self level on when i want to hover in one place but for unknown reason after some time of hoveing - quadcopter just flips over to the side and crashes. Actually when i turn on the selflevel it starts oscilating a bit, when self level is off it behaves more or less normal. well didnt have a crash yet when self level was off. what can be done here. should i reduce setting in Self level menu? is it settings related or some other causes may lead to overflipping?
+Iron Man I've not used the KK2.x board in over a year as I use boards with more features now - the firmware shown in this video was the last one I tried. I would check the forums for similar instances and see if there is a common cause. In the mean time I would check the frame for vibration (motors and props) as this can cause some 'odd' things to happen.Best of luck.
checking the rcgroup right now as to this issue. regarding vibration - well i thought about it. yes that may also be the case. good thing you mentioned about it i will get more attention to it. may be i wil need to put KK on antivibration mount or something. right now it is firmly attached to the plate with double sided stick tape on some with PU foam. but may it is not good enough for vibration dampening. thanks for your answer. keep up with great videos!
Is your model using a KK 2.0 flight controller? I guess you’ve already used the search function to find my video on it? ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-g338Sd-JmB4.html
Happy to help but please watch ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-olIqTiSJHIY.html and come back to me with more detail of what you've tried..
+Huw John - You do it like this --- connect a male to male JR lead between AUX receiver socket to the KK2 Input channel 5 --- now just toggle your ch' 5 switch for on/.off on your TX. (usually the gear switch on most TX's)
You need ot check esch piece of the puzzle in turn to find out what's not happy. Have you tried looking at the monitor on the TX and seeing is you can see the value move? If so, connect a servo to the throttle on the Rx and see if that moves as you move the stick on the TX, if that all works then check the cable from the Rx to the MWC as it may have a bad joint. Hope this helps.
if I put wires in from the rx to any of the inputs they work but the throttle .it says no signal .I have put the esc in the rx and it works .now I have put the esc in to the throttle pins and it powers up.i put the esc to the number 1m and power up that way and still have the same no signal .this was working and I was flying it was good but then this happened ????
