Quadcopter X & HK KK2.0 FW V1.5 Vol.49 Test Flight 

What is your transmitter? I mean what is the stick resolution ? My F450 is drifting to one direction frequently i guess this a problem caused by the transmitter.

Luis Pinho how prop is balanced

Thank you for viewing.I think it to be available by the same setting.Currently, I'm using KK-Mini.

Sorry for my late reply.I appreciate your comments.I am going to make Hexacopter in next week.Thank you

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-GJy2P2zqEGQ.html

I have the same Issues with my 450mm / Quadricopter , this is the same frame showed in this video , mine is pretty heavy ( 1,116Kg : LiPo 5000mAh = 416g ), but With theyre settup my craft should be controlable , bullshit , it allways slide , or turn around it self ( around the yaw axis ) , and the self level is counting the birds when i fly because it control apparently nothing ... I plan to buy an APM 2.6 because I've a lot of shields that I can use it with APM , like GPS or some gyro and magneto in shield design ... but I would like to know why my 450 doesn't fly like this one ... ( allready 50 or more hours to try to set up this board and nothing change ... even after balancing ALL the components , and insolate the board from the frame ...

i've got it flying moderately well now but like you say it has taken me HOURS! I've got a new setup (longer arms, different motors etc - on my channel if you want to see it) but i really want to get a new control board because the KK is just not working out for me!

Well :) Can you share your PI settings and autolevel settings , to compare with mine , I think I have some vibration issues with my quad , so I would like to test the last settings and if there is no changes , I will rebuilt all , with vibration absorbers , new balanced props , and perhaps another flight controler , I would like to test APM 2.6 as I already have FPV system I will have telemetry returns , and many informations too , and I will be able to connect external Acc and Gyro and dataloger with my Arduino embed on the quad to record some information, as I already work around Arduino This will be easier , cause I allready have some shields to do that :)

for kk2 all my settings are: roll/pitch p gain:60, P limit: 100, I gain: 35, I limit 20 Yaw P gain:120, P limit:20, I gain: 40, I limit:10 Stick Scaling roll:55, pitch: 50, Yaw: 65, Throttle: 90 Self level: P gain: 100, P limit:20 This was my last picture of my settings and they seem to work well, not too touchy etc. Seems to be working moderately well :)

Yep :) These are pretty the same : Roll/pitch Pgain:75 ; Plimit 100 ; I gain 32; I limit 20 Yaw : Pgain : 100 : Plimit 20; I gain 40 ; I limit 20 Stick scaling : roll / pitch 30 ; Yaw 50 ; Throttle : 90 Self level : P gain 100 ; P limit 20 But I never Find anybody who can tell me about the value LIMIT in every settings ... What is this ??? Limit of What ? At this time , for me If I put 80 for P gain and limit at 100 what is the value of this limit ? 100 potatoes ? 100 Percent ? and what is the min and the max value we can put in any setting ... Did you see this information anywhere ? Cause I don't undestand what does the limit value do ... perhaps my problem start here , If I understand this value perhaps I'll find where is my problem and solve it ... I juste notice that Higher P gain is , better the craft respond to my stick , but I ( integer ) I don't know ... If I put 30 in I gain does this mean that the reaction against wind or something else would append 30 seconds after ? or 30/100 seconds ? I tried to let the I gain at 0 , then I don't see any changes to the flght ... Last thing , perhaps my board is wrecked ... duno :(

Mine also behaves similar on Auto level, i havent checked if its M1 or not, but it sometimes starts its slow acceleration, and its very twitchy on Autolevel, (maybe bad PID settings?)

Come Aun had u got solution??

check battery

@@iwantitpaintedblack set auto level settings and height dampening settings, they all play big part in stability of your craft

@@bramskahoon4072 Its a 5 Year old comment hahahah, i sold the kk board and bought STM32 based. with Betaflight

Thank you for your comment. Execute "acc calibration".

And what pid setting is should keep the basics only?

Ganesh Ustav have u solved

Bro go to mode settings and select level level and change it to alwals