No video :(

SHARK IF250uk Taken apart, Remove bin, access motor, control board removal, Cordless vacuum cleaner

Подписаться 700

Просмотров 8 тыс.

50% 1

Please DONATE a small amount to help me improve and expand on future videos, at the moment I do not have enough subscribers so am hoping people will be kind in donating especially if it has helped and saved them money.
Either go on my home page to see the PayPal link or copy and paste the following to go to PayPals safe and secure donating page, thank you.
www.paypal.com... I'm no professional so video isn't the best but its just a guide to show the shark IF250uk being taken apart, it will show screw locations etc which you might be struggling to find.
This will be the same on the following models.
IF130ukth, IF200uk, IF200ukt, IF250ukt, IF250ukco, IF260ukth.

Опубликовано:

6 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 21

@adamburton2165 11 месяцев назад

I am always reluctant to advise on tools needed because I’ve taken hundreds if not thousands of shark vacuum cleaners apart and the exact same model can have different size screws, but the basics are you need a torx bit with a hole in the end, common sizes used it T9, T10, T15 and T20, but the 2 screws inside the bin are usually a small cross headed type.

@johannamcghee6063 11 месяцев назад

Thanks bought them

@paulhendrick7640 4 месяца назад

thanks for the video. is it a brushless motor? my one tries to start up but ultimately wont start.

@lagunafishing 3 месяца назад

Did you find out? Mine tries to start too but immediately cuts out.

@johannamcghee6063 11 месяцев назад

What screw driver removes the screws does anyone know

@lagunafishing 3 месяца назад

Mine tries to start but immediately cuts out. Any idea why and can it be fixed?

@tonymarshall4353 2 месяца назад

Check the continuity of the 3 wires that run through the wand. Mine has a break in continuity on one of the wires in the wand. The vacuum starts, speed goes very high and then stops with flashing lights on the vacuum head. I'm currently struggling to dismantle the wand.

@christinemoore2253 Год назад

what screw driver did you use?

@user-xb3mj7wg3x 8 месяцев назад

Hello how many screws should i be getting out of the bin please ?

@salehnasr8356 11 месяцев назад

Excuse me sir, can you help me with my problem please tell me where can I buy a motor for shark vacuum model IF201 because water goes inside the motor and vacuum stop working

@jefflbi Год назад

I found this video very helpful in taking mine apart, but there is no way to clean the motor, and mine sounds like it's about to take off! It's gotten very loud. I'm afraid it's beyond fixing........

@lagunafishing 3 месяца назад

Did you throw it out or find a fix? Mine tries to start too but immediately cuts out.

@jefflbi 3 месяца назад

@@lagunafishing I tossed it. I would gladly buy another one since the batteries are still good, but they've changed the design and no longer use the same batteries.

@lagunafishing 3 месяца назад

@@jefflbi Yeah shame you can't buy these anymore. Wife bought a replacement battery for ours thinking that was the issue. However it must be something else as they are good. So far I've got it stripped down to expose the motor, now I'm wondering if the brushes might be worn or dust contamination deep inside. Thanks for responding anyway.

@adamburton2165 2 года назад

To which part?

@raheltefesetewold4046 Год назад

Is there a reverse video?

@adamburton2165 Год назад

No at the time of making video I wasn’t interested in doing a reverse video, but at each stage you are struggling with if you pause the video it may help, regards

@BeFearless_.1 2 года назад

There's not enough screws!

@D_A_M-091 18 дней назад

Thank you for having the only video on RU-vid of taking this thing apart, but could you maybe save the recording for your 2nd time around on it? It would be helpful to skip all the wasted time of you fumbling around with it, trying to figure it out. My advice, take it apart, put it back together, THEN tape yourself taking it apart the 2nd time. Also, move the camera. Maybe a bird's eye view. The only thing worse than watching you fumble around for 17 minutes was not being able to see anything because your giant diabetes hand was right in front of the camera. If you're gonna be a RU-vidr, put the effort in and do it right. Sorry, I didn't mean to be mean, but I got very frustrated. Thank you for trying.

@adamburton2165 16 дней назад

Thank you, but maybe you should take the time in making the videos yourself, the time it takes, editing, uploading and everything it takes and oh yeah, for nothing, I get paid nothing for trying to help people save their items from landfill, saving them money, not me, what do i save by making these videos???