[SJSE18] Jaguar XF Front & Rear Rotors & Pads 

Great video. No taking, no stupid music, good camera work, everything you need to see, nothing you don't. Excellent work.

The best of all the Jaguar XF rear brake videos. All in detail and a steady, clear vision of all the components. Great work!

Ideal great video thanks for taking the time to share

This video really helped. My jag xf is in Canada 220 000km. Had a shimmy feeling in the breaks ... and lots of life left. Swapped out for cross drilled. I had to so a extra step. I had to sand and file the anchor area of the calipers... where the pads anchor. It had divots from no caliper grease.

THIE GUY IS A PRO OUTER ALL I HAVE SEEN HE IS GOOD I DONE BRAKE KEEP UP

Thank you very much. I just bought a 2009 XF. Your video was excellent. Much appreciated.

Nice and easy tutorial 🤩

You should set up an affiliate account with Amazon and then create links for all the products you use so you can get paid when people purchase those things. I have watched this video SO MUCH in preparation for doing a brake/rotor job on my XF and I would have GLADLY clicked on links and purchased the products from Amazon to support you! THANK YOU for this video!

Dang, earning some serious Saturday afternoon beers too

Spot on, apart from you never torqued the carrier or slider bolts or mentioned what the torques are.

Can you also list the tools you used to do this?

can you elaborate on "Recalibrate parking brake" How do you do that?

Hi Hilton ,would you know the size of the Bangor copper washers on the rear callipers on XF .regards steve

Where can I buy the after market Any pad, rotors, and sensor? Any recommendation?

Useful, thanks. Looks like you've done these many times. I'm curious - what are you spraying from the bottle to clean up the cast iron pieces? Thanks

Excellent video mate. I have a question, should I always change the rotors every time when I replace the pads? All the best mate from John in the UK

Hi, could you please explain how to Recalibrate parking brake?, also how do i release it before starting the job without software?, do i use the emergency release switch? thx

Can I follow the same steps for a 2017 Jaguar XE?

I have a Jaguar 2017 and everytime I push the break it has like q noise how much do I think it will cost to change breaks on this car?

Be interested to know what sort of grease you smeared on the face of the rear piston - looked like the same type you put on the edges of the pads - anti-squeal. Just concerned that it was very close to the piston's rubber boot, and wondering whether there's a risk of it attacking the rubber?

Do you need any specific electronic tools to put epb into maintenance mode before working on the rears? If not, how do you recalibrate once finished? Thanks

Is this a 2019? If so, did you have to use a computer to release the brakes or something?

Do you want to set up your computer first before open rear brake

What size hex key is this ?

Job well done! What flex head ratchet you using on the rears dude?

If the rear pistons are would back (in) more than is required to allow the new pads to fit the disc (rotor) will they automatically come out to the correct position when in use or is 'distance in' important? Do you know do rear pistons for XE also have to be wound in?

I just changed the front pads and now I hear a knocking sound on the driver's side any ideas as to what could be causing it?

What Size Socket Did You Use ? Thanks

What about how to turn off low brake pad light?

Hey, what point did you use the floor jack on? I see you placed a jack stand on the pinch weld, but the floor jack was further towards the middle. My XF has plastic under body panels that shroud the frame, did you jack the car from the frame with the plastic under body panels still in place?

Not one single answer on what size tools to use...

Do I need to replace the sensor wire every time I change my brakes ? Or can I change them without disconnecting it

Where are you located

Hi, Great video. I intend to replace the brake rotors and pads on my XF soon. What kind of lubricant do you use for the guide pins? Silicone or copper lubricant? For the brake caliper bracket and pads corners i'm planning to use copper lubricant. Good idea? Thanks in advance and keep up the good work

Must the brake rotor be changed with the brakes?

My new pads don’t touch the inner part of the disc .why is this ?

How much do u charge for a job like this

are there sensors on both side?

Bad design for break indicator

Wow, no thread lock on the retaining bolts and didn't torque them up! Not a professional job at all.